Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 4 of 4

Thread: E7300 and UD3P settings works here




  1. #1

    Thumbs up E7300 and UD3P settings works here

    Updated:To run with Load Line Disabled
    In the Voltage area figures now for Load Line Disabled in brackets
    There are four voltage changes for this to operate 100% stable(here)
    all other voltage settings remain unchanged.

    Running load Line enabled

    If this helps somebody so be it
    no ide opticals or hds all satas
    what I don't have is turned off
    what bios/cmos doesn't have to deal with helps...I hope

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................:10x
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................:3.55(355x10)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 355Mhz
    PCI Express Frequency (Mhz) .........:Set to 100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................:700
    PCI Express Clock Drive.................:700
    CPU Clock Skew (ps)....................:100
    MCH Clock Skew (ps)...................:200


    DRAM Performance Control
    Performance Enhance...................: [Extreme]
    Extreme Memory Profile (X.M.P.).....:Auto
    (G)MCH Frequency Latch...............: 333
    System Memory Multiplier ..............:2.40b
    Memory Frequency (Mhz) ..............:800-852 actual
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time................5
    tRCD .................................4
    tRP'....................................4
    tRAS..................................12



    Advanced Timing Control
    tRRD...........................................3
    tWTR..........................................3
    tWR............................................6
    tRFC...........................................52
    tRTP...........................................3
    Command Rate (CMD) ....................2 or 1 either settings passes
    2 tested more thoroughly Auto is same.Just left on Auto.

    Driving Strength Profiles
    Driving Strength ............................Auto

    Channel A
    Static tRead Value.........................:7
    tRD Phase0 Adjustment...................:0
    tRD Phase1 Adjustment...................:0
    tRD Phase2 Adjustment ..................:0
    tRD Phase3 Adjustment...................:0
    Trd2rd(Different Rank)....................:6
    Twr2wr(Different Rank)...................:6
    Twr2rd(Different Rank)...................:5
    Trd2wr(Same/Diff Rank)..................:8
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto

    Channel B
    Static tRead Value.........................:7

    tRD Phase0 Adjustment...................:0
    tRD Phase1 Adjustment...................:0
    tRD Phase2 Adjustment ..................:0
    tRD Phase3 Adjustment...................:0
    Trd2rd(Different Rank)....................:6
    Twr2wr(Different Rank)...................:6
    Twr2rd(Different Rank)....................:5
    Trd2wr(Same/Diff Rank)..................:8
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:1.33750v(Load Line disabled:1.36250v) NOTE: runs also 1.33125v Load Line Enabled OCCT 3.0.1 Linpak custom test mode 3 hr\test mode mid(50%free memory)


    Load Line Calibration..................Enabled

    CPU Termination…..... 1.320V(Load Line disabled 1.360v)

    CPU PLL…………………....1.500V

    CPU Reference.…………....0.876v(Load Line Disabled 0.901v)



    MCH/ICH
    MCH Core…………….....1.100V
    MCH Reference….…….0.836v(Load Line Disabled 0.781v)
    MCH/DRAM Ref.…......0.980v
    ICH I/O……………….....1.500V
    ICH Core…………...……1.100V

    DRAM
    DRAM Voltage ……....1.96v
    DRAM Termination .…0.980v
    Channel A Reference 0.980v
    Channel B Reference 0.980v

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Enabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

    Integrated Peripherals
    Legacy USB Storage Detect ..............Enabled

    Other settings

    Lan 1 enabled
    Lan2 disabled
    green lan disabled
    on board serial port 1 disabled
    on board parallel port 1 disabled
    On board sata/ide device disabled
    onboard 1394 enabled
    sata port 0-3 native mode enabled
    sata raid ahci disabled
    All usb 1.0/2.0 controller enabled
    have usb mouse and keyboard all that enabled
    floppy drive1.44 enabled I use one
    floppy 3 mode support disabled
    delay for hdd 0
    hdd smart drv disabled
    initial display first PEG
    first boot device OS hard drive
    I use boot F12 key for anything else I need to call up
    2nd boot device disabled
    3rd boot device disabled
    password check set up not used
    cpu warning tmp 70c/158f
    cpu fan fail warning enabled
    power fan fail warning disabled
    sytem fan fail warning disabled
    cpu smart fan control disabled have arctic freezer pro on want it on from get go.
    pnp/pci all autos


    Bios F7

    memory mem tested 4 passes
    LinX 0.58
    Intel Burn test
    pounded with OCCT3.0.1 on Linpak Maximum (90%free memory) 3 hours. NOTE:See OCCT Linpak test above for 1.33125v on OCCT 50%free memory
    for several hours


    Really Happy with this board so far
    Last edited by Tyreman; 04-17-2009 at 06:21 PM.
    Asus P8Z68-V PRO/GEN3 bios 3202
    2500k@4.7GHZ.
    CM Hyper 212 EVO blademasters push-pull
    8GB's Samsung 30nm tech ram 1.35v
    EVGA GTX 460 superclocked plus (part# 1G-P3-1372-TR)
    Seasonic X660
    Canada

  2. #2
    kick's Avatar
    kick is offline Senior Member
    Join Date
    Feb 2009
    Location
    Europe,the wild wild west.
    Posts
    1,223

    Default Re: E7300 and UD3P settings works here

    Grats tyre,im glad extreme works for you.Its not gonna happen for me :)
    Current Systems:

    Asrock p67 Extreme6.............. Gigabyte EP-45 UD3 ...................... Gigabyte 73 PVM S2
    Intel i5 2500k 4.8ghz................ Intel Q8400 3.8ghz......................... Intel D820 2.8ghz
    Zalman 10x cooler.................... Coolermaster V8............................ HP cooler
    8GB Gskill ripjaw ddr3.............. 4GB Gskill PI ddr2.......................... 4GB samsung ddr2
    60GB ssd/500GB HDD .............. WD 1TB hdd.................................... Seagate 160GB hdd
    GTX 460 1GB x2 SLI ................. Msi 9600GT 512MB(died) ........... Onboard gx
    Win7 64 ,750w psu(ocz)............ Win7 64 ,520w psu,seasonic...... Win XP pro ,400w psu

    HEC 6A34 case . ....................... Jeantec R2 case............................ Packard Bell case

    hoping to upgrade to http://www.thinkgeek.com/stuff/41/habicase.shtml
    http://www.flixya.com/video/140325/Animal-launching

  3. #3

    Default Re: E7300 and UD3P settings works here

    I just got lucky with it Kick
    Thanks for answering some of my questions I appreciate it

    This the best board I have ever used period!
    Last edited by Tyreman; 04-10-2009 at 06:05 AM.
    Asus P8Z68-V PRO/GEN3 bios 3202
    2500k@4.7GHZ.
    CM Hyper 212 EVO blademasters push-pull
    8GB's Samsung 30nm tech ram 1.35v
    EVGA GTX 460 superclocked plus (part# 1G-P3-1372-TR)
    Seasonic X660
    Canada

  4. #4

    Default Re: E7300 and UD3P settings works here

    Update on Settings for Load Line Disabled.
    Asus P8Z68-V PRO/GEN3 bios 3202
    2500k@4.7GHZ.
    CM Hyper 212 EVO blademasters push-pull
    8GB's Samsung 30nm tech ram 1.35v
    EVGA GTX 460 superclocked plus (part# 1G-P3-1372-TR)
    Seasonic X660
    Canada

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •