Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 3 of 6 FirstFirst 12345 ... LastLast
Results 21 to 30 of 55

Thread: EP45-UD3P (F9) - Backup BIOS Recovery Source?




  1. #21
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: EP45-UD3P (F9) - Backup BIOS Recovery Source?

    Yes, next one closest up/down is fine. Some boards just have different available adjustments is why you see that.

    Ya, some of those lower values, voltage or timings, may not fully work together. You would want to tighten down your ram timings first then lower your voltages afterwords. Or if you are going to lowest voltages you may need to do that the other way around, depending on how low you are trying to go.

  2. #22

    Unhappy Re: EP45-UD3P (F9) - Backup BIOS Recovery Source?

    The template below resulted in the error below that, it appeared AFTER the scrolling Microsoft Windows thingy but BEFORE the big Microsoft Orb appears...

    Code:
    *************************************
    *************************************
    Gigabyte GA-EP45-UD3P (Rev. 1.0) - F9
    *************************************
    *************************************
    
    ******************************
    MB Intelligent Tweaker(M.I.T.) 
    ******************************
    Robust Graphics Booster ..............: [Fast] 
    CPU Clock Ratio ......................: [8X] 
    CPU Frequency ........................: 3.20GHz( 401x8)
    
    ********** Clock Chip Control ********
    
    >>>>>  Standard Clock Control 
    CPU Host Clock Control................: [Enabled] 
    x CPU Host Frequency(Mhz).............: 401
    PCI Express Frequency(Mhz)............: [100] 
    C.I.A.2...............................: [Disabled] 
    
    >>>>> Advanced Clock Control..........: [Press Enter] 
    CPU Clock Drive.......................: [800mV]
    PCI Express Clock Drive...............: [900mV]
    CPU Clock Skew........................: [  0ps]
    MCH Clock Skew........................: [  0ps]
    
    ******** DRAM Performance Control ********
    
    Performance Enhance...................: [Standard]
    (G)MCH Frequency Latch................: [Auto]
    System Memory Multiplier (SPD)........: [2.00B]
    Memory Frequency(Mhz).....800.........: 802
    DRAM Timing Selectable (SPD)..........: [Manual]
    
    >>>>> Standard Timing Control
    x CAS Latency Time....................:  5
    x tRCD ...............................:  5
    x tRP.................................:  5
    x tRAS................................: 15 (18 gives same error)
    
    >>>>> Advanced Timing Control.........: [Press Enter] 
    x tRRD................................: [ 4]
    x tWTR................................: [ 6]
    x tWR.................................: [ 6]
    x tRFC................................: [62]
    x tRTP................................: [ 5]
    x Command Rate (CMD) .................: [ 2]
    
    >>>>> Channel A Timing Settings.......: [Press Enter] 
    x Static tRead Value..................: [10]
    x tRD Phase0 Adjustment...............: [ 0] Auto
    x tRD Phase1 Adjustment...............: [ 0] Auto
    x tRD Phase2 Adjustment ..............: [ 1] Auto
    x tRD Phase3 Adjustment...............: [ 1] Auto
    
    x Trd2rd(Different Rank)..............: [ 6] Auto
    x Twr2wr(Different Rank)..............: [ 6] Auto
    x Twr2rd(Different Rank)..............: [ 5] Auto
    x Trd2wr(Same/Diff Rank)..............: [ 8] Auto
    
    x DIMM1 Clock Skew Control (ps).......: [  ] Auto
    x DIMM2 Clock Skew Control (ps).......: [  ] Auto
    x DDR Write Training..................: [  ] Auto
    
    >>>>> Channel A Driving Settings......: [Press Enter] 
    x Driving Strength Profile............: 800
    
    x Data Driving Pull-Up Level..........: Auto
    x Cmd Driving Pull-Up level...........: Auto
    x Ctrl Driving Pull-Up Level..........: Auto
    x Clk Driving Pull-Up Level...........: Auto
    
    x Data Driving Pull-Down Level........: Auto
    x Cmd Driving Pull-Down level.........: Auto
    x Ctrl Driving Pull-Down Level........: Auto
    x Clk Driving Pull-Down Level.........: Auto
    
    >>>>> Channel B Timing Settings.......: [Press Enter] 
    x Static tRead Value..................: [10]
    x tRD Phase0 Adjustment...............: [ 0] Auto
    x tRD Phase1 Adjustment...............: [ 0] Auto
    x tRD Phase2 Adjustment ..............: [ 1] Auto
    x tRD Phase3 Adjustment...............: [ 1] Auto
    
    x Trd2rd(Different Rank)..............: [ 6] Auto
    x Twr2wr(Different Rank)..............: [ 6] Auto
    x Twr2rd(Different Rank)..............: [ 5] Auto
    x Trd2wr(Same/Diff Rank)..............: [ 8] Auto
    
    x DIMM1 Clock Skew Control (ps).......: [  ] Auto
    x DIMM2 Clock Skew Control (ps).......: [  ] Auto
    x DDR Write Training..................: [  ] Auto
    
    >>>>> Channel B Driving Settings......: [Press Enter] 
    x Driving Strength Profile............: 800
    
    x Data Driving Pull-Up Level..........: Auto
    x Cmd Driving Pull-Up level...........: Auto
    x Ctrl Driving Pull-Up Level..........: Auto
    x Clk Driving Pull-Up Level...........: Auto
    
    x Data Driving Pull-Down Level........: Auto
    x Cmd Driving Pull-Down level.........: Auto
    x Ctrl Driving Pull-Down Level........: Auto
    x Clk Driving Pull-Down Level.........: Auto
    
    ****** Motherboard Voltage Control ******
    
    Voltage Types..........Normal...........Current
    -----------------------------------------------
    >>> CPU
    Load-Line Calibration.................: [Disabled]
    CPU Vcore..............1.32500V.......: [1.44375V]
    CPU Termination........1.200V.........: [1.400V]
    CPU PLL................1.500V.........: [1.610V]
    CPU Reference..........0.760V.........: [Auto]
    >>> MCH/ICH
    MCH Core...............1.100V.........: [1.240V]
    MCH Reference..........0.760V.........: [Auto]
    MCH/DRAM Reference.....0.900V.........: [Auto]
    ICH I/O................1.500V.........: [1.570V]
    ICH Core...............1.100V.........: [1.200V]
    >>> DRAM
    DRAM Voltage...........1.800V.........: [2.100V]
    DRAM Termination.......0.900V.........: [Auto]
    Channel A Reference....0.900V.........: [Auto]
    Channel B Reference....0.900V.........: [Auto]
    
    ******** Advanced BIOS Features ********
    Hard Disk Boot Priority...............: [Press Enter]
    First Boot Device.....................: [Floppy]
    Second Boot Device....................: [Hard Disk]
    Third Boot Device.....................: [CDROM]
    Password Check........................: [Setup]
    HDD S.M.A.R.T. Capability.............: [Enabled]
    CPU Multi-Threading...................: [Enabled]
    Limit CPUID Max. to 3.................: [Disabled]
    No-Execute Memory Protect.............: [Enabled]
    CPU Enhanced Halt (C1E)...............: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.....................: [Disabled]
    Virtualization Technology.............: [Disabled]
    Delay For HDD (Secs)..................: [ 0]
    Full Screen LOGO Show.................: [Disabled]
    Init Display First....................: [PCI]
    
    ******** Integrated Peripherals ********
    USB Keyboard Function.................: [Enabled]
    USB Mouse Function....................: [Enabled]
    USB Storage Function..................: [Disabled]
    * CPU: Intel i7-3770K @ Stock * Cooling: Corsair H80i / Noctua NF-F12 x2 * MoBo: Gigabyte GA-Z77X-UD5H (Rev. 1.1 - BIOS F16 Mod16) * RAM: Crucial 1600MHz DDR3 32GB (4x8GB) *
    * GPU: Intel HD 4000 (768MB) * Mon 1: Dell U2410 (A07) * Mon 2: Panasonic TX-P55VT50B * Cam: Logitech C910 HD * BD: Pioneer BDR-208DBK * HD 1: Crucial SSD M4-CT256M4SSD2 256GB *
    * HD 2: Western Digital Caviar Green 3TB * IR: Apple Infrared Board 922-7195 * WiFi & BT: Apple Broadcom BCM94360CD (802.11 a/b/g/n/ac - Bluetooth 4.0 * PSU: Seasonic M12 - 600W *

  3. #23
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: EP45-UD3P (F9) - Backup BIOS Recovery Source?

    Your volt settings are too high, try:

    CPU Vcore..............1.32500V.......: [1.44375V] <-- 1.33250 - 1.33875
    CPU Termination......1.200V..........: [1.400V] <-- 1.20 - 1.22
    CPU PLL.................1.500V..........: [1.610V] <-- 1.50 - 1.57

    MCH Core................1.100V.........: [1.240V] <-- less should help stability (with 2x2GB 800 MHz memory)
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  4. #24

    Default Re: EP45-UD3P (F9) - Backup BIOS Recovery Source?

    Just tried those voltages, after saving the settings in the BIOS the PC reboots twice and on the second boot the CPU is shown as 2.13GHz. Also when I enter the MIT section I get a red warning box telling me it didn't like something I did!

    Code:
    *************************************
    *************************************
    Gigabyte GA-EP45-UD3P (Rev. 1.0) - F9
    *************************************
    *************************************
    
    ******************************
    MB Intelligent Tweaker(M.I.T.) 
    ******************************
    Robust Graphics Booster ..............: [Fast] 
    CPU Clock Ratio ......................: [8X] 
    CPU Frequency ........................: 3.20GHz( 401x8)
    
    ********** Clock Chip Control ********
    
    >>>>>  Standard Clock Control 
    CPU Host Clock Control................: [Enabled] 
    x CPU Host Frequency(Mhz).............: 401
    PCI Express Frequency(Mhz)............: [100] 
    C.I.A.2...............................: [Disabled] 
    
    >>>>> Advanced Clock Control..........: [Press Enter] 
    CPU Clock Drive.......................: [800mV]
    PCI Express Clock Drive...............: [900mV]
    CPU Clock Skew........................: [  0ps]
    MCH Clock Skew........................: [  0ps]
    
    ******** DRAM Performance Control ********
    
    Performance Enhance...................: [Standard]
    (G)MCH Frequency Latch................: [Auto]
    System Memory Multiplier (SPD)........: [2.00B]
    Memory Frequency(Mhz).....800.........: 802
    DRAM Timing Selectable (SPD)..........: [Manual]
    
    >>>>> Standard Timing Control
    x CAS Latency Time....................:  5
    x tRCD ...............................:  5
    x tRP.................................:  5
    x tRAS................................: 15 (18 gives same error)
    
    >>>>> Advanced Timing Control.........: [Press Enter] 
    x tRRD................................: [ 4]
    x tWTR................................: [ 6]
    x tWR.................................: [ 6]
    x tRFC................................: [62]
    x tRTP................................: [ 5]
    x Command Rate (CMD) .................: [ 2]
    
    >>>>> Channel A Timing Settings.......: [Press Enter] 
    x Static tRead Value..................: [10]
    x tRD Phase0 Adjustment...............: [ 0] Auto
    x tRD Phase1 Adjustment...............: [ 0] Auto
    x tRD Phase2 Adjustment ..............: [ 1] Auto
    x tRD Phase3 Adjustment...............: [ 1] Auto
    
    x Trd2rd(Different Rank)..............: [ 6] Auto
    x Twr2wr(Different Rank)..............: [ 6] Auto
    x Twr2rd(Different Rank)..............: [ 5] Auto
    x Trd2wr(Same/Diff Rank)..............: [ 8] Auto
    
    x DIMM1 Clock Skew Control (ps).......: [  ] Auto
    x DIMM2 Clock Skew Control (ps).......: [  ] Auto
    x DDR Write Training..................: [  ] Auto
    
    >>>>> Channel A Driving Settings......: [Press Enter] 
    x Driving Strength Profile............: 800
    
    x Data Driving Pull-Up Level..........: Auto
    x Cmd Driving Pull-Up level...........: Auto
    x Ctrl Driving Pull-Up Level..........: Auto
    x Clk Driving Pull-Up Level...........: Auto
    
    x Data Driving Pull-Down Level........: Auto
    x Cmd Driving Pull-Down level.........: Auto
    x Ctrl Driving Pull-Down Level........: Auto
    x Clk Driving Pull-Down Level.........: Auto
    
    >>>>> Channel B Timing Settings.......: [Press Enter] 
    x Static tRead Value..................: [10]
    x tRD Phase0 Adjustment...............: [ 0] Auto
    x tRD Phase1 Adjustment...............: [ 0] Auto
    x tRD Phase2 Adjustment ..............: [ 1] Auto
    x tRD Phase3 Adjustment...............: [ 1] Auto
    
    x Trd2rd(Different Rank)..............: [ 6] Auto
    x Twr2wr(Different Rank)..............: [ 6] Auto
    x Twr2rd(Different Rank)..............: [ 5] Auto
    x Trd2wr(Same/Diff Rank)..............: [ 8] Auto
    
    x DIMM1 Clock Skew Control (ps).......: [  ] Auto
    x DIMM2 Clock Skew Control (ps).......: [  ] Auto
    x DDR Write Training..................: [  ] Auto
    
    >>>>> Channel B Driving Settings......: [Press Enter] 
    x Driving Strength Profile............: 800
    
    x Data Driving Pull-Up Level..........: Auto
    x Cmd Driving Pull-Up level...........: Auto
    x Ctrl Driving Pull-Up Level..........: Auto
    x Clk Driving Pull-Up Level...........: Auto
    
    x Data Driving Pull-Down Level........: Auto
    x Cmd Driving Pull-Down level.........: Auto
    x Ctrl Driving Pull-Down Level........: Auto
    x Clk Driving Pull-Down Level.........: Auto
    
    ****** Motherboard Voltage Control ******
    
    Voltage Types..........Normal...........Current
    -----------------------------------------------
    >>> CPU
    Load-Line Calibration.................: [Disabled]
    CPU Vcore..............1.32500V.......: [1.33750V]
    CPU Termination........1.200V.........: [1.220V]
    CPU PLL................1.500V.........: [1.570V]
    CPU Reference..........0.760V.........: [Auto]
    >>> MCH/ICH
    MCH Core...............1.100V.........: [1.240V]
    MCH Reference..........0.760V.........: [Auto]
    MCH/DRAM Reference.....0.900V.........: [Auto]
    ICH I/O................1.500V.........: [1.570V]
    ICH Core...............1.100V.........: [1.200V]
    >>> DRAM
    DRAM Voltage...........1.800V.........: [2.100V]
    DRAM Termination.......0.900V.........: [Auto]
    Channel A Reference....0.900V.........: [Auto]
    Channel B Reference....0.900V.........: [Auto]
    
    ******** Advanced BIOS Features ********
    Hard Disk Boot Priority...............: [Press Enter]
    First Boot Device.....................: [Floppy]
    Second Boot Device....................: [Hard Disk]
    Third Boot Device.....................: [CDROM]
    Password Check........................: [Setup]
    HDD S.M.A.R.T. Capability.............: [Enabled]
    CPU Multi-Threading...................: [Enabled]
    Limit CPUID Max. to 3.................: [Disabled]
    No-Execute Memory Protect.............: [Enabled]
    CPU Enhanced Halt (C1E)...............: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.....................: [Disabled]
    Virtualization Technology.............: [Disabled]
    Delay For HDD (Secs)..................: [ 0]
    Full Screen LOGO Show.................: [Disabled]
    Init Display First....................: [PCI]
    
    ******** Integrated Peripherals ********
    USB Keyboard Function.................: [Enabled]
    USB Mouse Function....................: [Enabled]
    USB Storage Function..................: [Disabled]
    Last edited by D-an-W; 04-30-2009 at 07:13 AM. Reason: Added updated template...
    * CPU: Intel i7-3770K @ Stock * Cooling: Corsair H80i / Noctua NF-F12 x2 * MoBo: Gigabyte GA-Z77X-UD5H (Rev. 1.1 - BIOS F16 Mod16) * RAM: Crucial 1600MHz DDR3 32GB (4x8GB) *
    * GPU: Intel HD 4000 (768MB) * Mon 1: Dell U2410 (A07) * Mon 2: Panasonic TX-P55VT50B * Cam: Logitech C910 HD * BD: Pioneer BDR-208DBK * HD 1: Crucial SSD M4-CT256M4SSD2 256GB *
    * HD 2: Western Digital Caviar Green 3TB * IR: Apple Infrared Board 922-7195 * WiFi & BT: Apple Broadcom BCM94360CD (802.11 a/b/g/n/ac - Bluetooth 4.0 * PSU: Seasonic M12 - 600W *

  5. #25
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: EP45-UD3P (F9) - Backup BIOS Recovery Source?

    The 0x00000124 BSOD can be caused by excessive voltages.
    You didn't say which specific suggested settings failed, so let's split the difference.

    CPU Vcore..............1.32500V.......: [1.44375V] <-- 1.36750
    CPU Termination......1.200V..........: [1.400V] <-- 1.30
    CPU PLL.................1.500V..........: [1.610V] <-- 1.57

    MCH Core................1.100V.........: [1.30] <-- some memory only works at 1.05 volts

    Your cpu and mine are closely related. I'm running a 48%+ o/c and the Vcore is 1.36250 (2 clicks more than my VID = 1.35 volts).
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  6. #26

    Default Re: EP45-UD3P (F9) - Backup BIOS Recovery Source?

    It wouldn't boot using those settings either I am afraid to say!

    First I tried...
    Code:
    CPU Vcore..............1.32500V.......: [1.33750V]
    CPU Termination........1.200V.........: [1.220V]
    CPU PLL................1.500V.........: [1.570V]
    CPU Reference..........0.760V.........: [Auto]
    >>> MCH/ICH
    MCH Core...............1.100V.........: [1.240V]
    Then I tried...
    Code:
    CPU Vcore..............1.32500V.......: [1.36875V]
    CPU Termination........1.200V.........: [1.300V]
    CPU PLL................1.500V.........: [1.570V]
    CPU Reference..........0.760V.........: [Auto]
    >>> MCH/ICH
    MCH Core...............1.100V.........: [1.300V]
    These are all in addition to the settings kindly suggested by Lsd as shown in the template two posts up.

    This time however there is no red warning box shown when I enter the MIT section of the BIOS.
    * CPU: Intel i7-3770K @ Stock * Cooling: Corsair H80i / Noctua NF-F12 x2 * MoBo: Gigabyte GA-Z77X-UD5H (Rev. 1.1 - BIOS F16 Mod16) * RAM: Crucial 1600MHz DDR3 32GB (4x8GB) *
    * GPU: Intel HD 4000 (768MB) * Mon 1: Dell U2410 (A07) * Mon 2: Panasonic TX-P55VT50B * Cam: Logitech C910 HD * BD: Pioneer BDR-208DBK * HD 1: Crucial SSD M4-CT256M4SSD2 256GB *
    * HD 2: Western Digital Caviar Green 3TB * IR: Apple Infrared Board 922-7195 * WiFi & BT: Apple Broadcom BCM94360CD (802.11 a/b/g/n/ac - Bluetooth 4.0 * PSU: Seasonic M12 - 600W *

  7. #27
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: EP45-UD3P (F9) - Backup BIOS Recovery Source?

    Have you done stability testing at stock speeds?
    If not:

    Load Optimized settings and make the following changes:

    Performance Enhance ------------------- : [Turbo] <--- set to Standard when overclocking
    Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <--- Leave this Disabled

    Motherboard Voltage Control
    CPU

    CPU Vcore --------------- 1.????? ------ : [Auto] <--- set to the 1.????? value displayed in your bios
    CPU Termination ---------- 1.200V* ----- : [Auto] <--- set to the value to the left (Auto over-volts this too much when overclocking) Auto is OK if not overclocking
    CPU PLL ------------------ 1.500V* ----- : [Auto] <--- set to the value to the left (Auto over-volts this too much when overclocking) Auto is OK if not overclocking

    MCH/ICH
    MCH Core ---------------- 1.100V ------- : [Auto] <--- set to 1.20 for 2x2GB ram (1.24 - 1.26, or 1.05 might be needed)

    ICH I/O ------------------ 1.500V ------- : [Auto] <--- set to the value displayed in your bios
    ICH Core ----------------- 1.100V ------- : [Auto] <--- set to the value displayed in your bios

    DRAM
    DRAM Voltage ------------ 1.800V ------- : [Auto] <--- set to the max rated ram voltage (for most memory)

    Advanced Settings -------- The following settings will improve system stability for overclocked systems.
    Limit CPUID Max. to 3 -------------------- : [Disabled]
    No-Execute Memory Protect -------------- : [Enabled]
    CPU Enhanced Halt (C1E) ----------------- : [Disabled]
    C2/C2E State Support -------------------- : [Disabled]
    x C4/C4E State Support ------------------ : [Disabled]
    CPU Thermal Monitor 2 (TM2) ------------- : [Enabled]
    CPU EIST Function ----------------------- : [Disabled]
    Virtualization Technology ----------------- : [Disabled] <--- Enabled if you use Vmware/Virtual PC

    Integrated Peripherals
    Legacy USB Storage Detect --------------- : [Enabled] <--- set to Disabled when overclocking (this must be enabled to flash or boot from a USB drive)
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  8. #28
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: EP45-UD3P (F9) - Backup BIOS Recovery Source?

    0x00000124 can also mean not enough Vtt (Termination) please try all your settings you was using you listed above post #22, except raise Vtt a notch or two and test again

  9. #29

    Default Re: EP45-UD3P (F9) - Backup BIOS Recovery Source?

    Excellent, thank you both very much. I will go test both and report back shorty...
    * CPU: Intel i7-3770K @ Stock * Cooling: Corsair H80i / Noctua NF-F12 x2 * MoBo: Gigabyte GA-Z77X-UD5H (Rev. 1.1 - BIOS F16 Mod16) * RAM: Crucial 1600MHz DDR3 32GB (4x8GB) *
    * GPU: Intel HD 4000 (768MB) * Mon 1: Dell U2410 (A07) * Mon 2: Panasonic TX-P55VT50B * Cam: Logitech C910 HD * BD: Pioneer BDR-208DBK * HD 1: Crucial SSD M4-CT256M4SSD2 256GB *
    * HD 2: Western Digital Caviar Green 3TB * IR: Apple Infrared Board 922-7195 * WiFi & BT: Apple Broadcom BCM94360CD (802.11 a/b/g/n/ac - Bluetooth 4.0 * PSU: Seasonic M12 - 600W *

  10. #30

    Default Re: EP45-UD3P (F9) - Backup BIOS Recovery Source?

    Quote Originally Posted by profJim View Post
    Have you done stability testing at stock speeds?
    If not:

    Load Optimized settings and make the following changes:

    Performance Enhance ------------------- : [Turbo] <--- set to Standard when overclocking
    Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <--- Leave this Disabled

    Motherboard Voltage Control
    CPU
    CPU Vcore --------------- 1.????? ------ : [Auto] <--- set to the 1.????? value displayed in your bios
    CPU Termination ---------- 1.200V* ----- : [Auto] <--- set to the value to the left (Auto over-volts this too much when overclocking) Auto is OK if not overclocking
    CPU PLL ------------------ 1.500V* ----- : [Auto] <--- set to the value to the left (Auto over-volts this too much when overclocking) Auto is OK if not overclocking

    MCH/ICH
    MCH Core ---------------- 1.100V ------- : [Auto] <--- set to 1.20 for 2x2GB ram (1.24 - 1.26, or 1.05 might be needed)

    ICH I/O ------------------ 1.500V ------- : [Auto] <--- set to the value displayed in your bios
    ICH Core ----------------- 1.100V ------- : [Auto] <--- set to the value displayed in your bios

    DRAM
    DRAM Voltage ------------ 1.800V ------- : [Auto] <--- set to the max rated ram voltage (for most memory)

    Advanced Settings -------- The following settings will improve system stability for overclocked systems.
    Limit CPUID Max. to 3 -------------------- : [Disabled]
    No-Execute Memory Protect -------------- : [Enabled]
    CPU Enhanced Halt (C1E) ----------------- : [Disabled]
    C2/C2E State Support -------------------- : [Disabled]
    x C4/C4E State Support ------------------ : [Disabled]
    CPU Thermal Monitor 2 (TM2) ------------- : [Enabled]
    CPU EIST Function ----------------------- : [Disabled]
    Virtualization Technology ----------------- : [Disabled] <--- Enabled if you use Vmware/Virtual PC

    Integrated Peripherals
    Legacy USB Storage Detect --------------- : [Enabled] <--- set to Disabled when overclocking (this must be enabled to flash or boot from a USB drive)
    Ok, using the following currently with a couple of discrepencies, what should I be stability testing it with?

    Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <---I don't have this option
    C2/C2E State Support -------------------- : [Disabled] <---I don't have this option
    x C4/C4E State Support ------------------ : [Disabled] <--- I don't have this option

    Code:
    Performance Enhance ------------------- : [Standard]
    Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <---Don't have
     
     
    Motherboard Voltage Control
    CPU
    CPU Vcore --------------- 1.32500V ------ : [1.32500V]
    CPU Termination ---------- 1.200V* ----- : [1.200V]
    CPU PLL ------------------ 1.500V* ----- : [1.500V]
     
    MCH/ICH
    MCH Core ---------------- 1.100V ------- : [1.200V]
     
    ICH I/O ------------------ 1.500V ------- : [1.500V]
    ICH Core ----------------- 1.100V ------- : [1.100V]
     
    DRAM
    DRAM Voltage ------------ 1.800V ------- : [1.800V]
     
    Advanced Settings --------
    Limit CPUID Max. to 3 -------------------- : [Disabled]
    No-Execute Memory Protect -------------- : [Enabled]
    CPU Enhanced Halt (C1E) ----------------- : [Disabled]
    C2/C2E State Support -------------------- : [Disabled] <---Don't have
    x C4/C4E State Support ------------------ : [Disabled] <---Don't have
    CPU Thermal Monitor 2 (TM2) ------------- : [Enabled]
    CPU EIST Function ----------------------- : [Disabled]
    Virtualization Technology ----------------- : [Disabled]
     
    Integrated Peripherals
    Legacy USB Storage Detect --------------- : [Disabled]
    Quote Originally Posted by Lsdmeasap View Post
    0x00000124 can also mean not enough Vtt (Termination) please try all your settings you was using you listed above post #22, except raise Vtt a notch or two and test again
    I quickly tested this before loading the above as I have a profile saved with the settings in, upping the Termination Voltage a couple of notches it did seem to go further than before but resulted in the same error before Windows completed booting.
    * CPU: Intel i7-3770K @ Stock * Cooling: Corsair H80i / Noctua NF-F12 x2 * MoBo: Gigabyte GA-Z77X-UD5H (Rev. 1.1 - BIOS F16 Mod16) * RAM: Crucial 1600MHz DDR3 32GB (4x8GB) *
    * GPU: Intel HD 4000 (768MB) * Mon 1: Dell U2410 (A07) * Mon 2: Panasonic TX-P55VT50B * Cam: Logitech C910 HD * BD: Pioneer BDR-208DBK * HD 1: Crucial SSD M4-CT256M4SSD2 256GB *
    * HD 2: Western Digital Caviar Green 3TB * IR: Apple Infrared Board 922-7195 * WiFi & BT: Apple Broadcom BCM94360CD (802.11 a/b/g/n/ac - Bluetooth 4.0 * PSU: Seasonic M12 - 600W *

Page 3 of 6 FirstFirst 12345 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •