Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 4 of 5 FirstFirst ... 2345 LastLast
Results 31 to 40 of 46

Thread: G.Skill memory for EP45-UD3P




  1. #31
    Join Date
    Apr 2009
    Location
    J'Habite En Angleterre
    Posts
    2,431

    Default Re: G.Skill memory for EP45-UD3P

    Vdrop is the difference in voltage set in the BIOS versus the voltage you see in CPU-Z.

    Vdroop is the amount by which processor voltage "droops" when you load the CPU

    It varies by motherboard, but usually the higher the voltages you set, the worse these two factors become, especially Vdroop. Load Line Calibration can virtually eliminate Vdroop, but often does nothing for Vdrop. Vdrop and Vdroop are both expected behaviours and are detailed in Intel spec sheets.

    And 1.424v is absolutely nothing to worry about. If your temperatures are fine then that kind of voltage will not kill your CPU. Depending on cooling, 1.5-1.6v (high end air/water, up to phase change) would be fine.
    Coolermaster CM 690 II advance Case
    Corsair HX750 (CWT, 91%(80+ Gold rated @230V) single 62A 12V rail
    P55A-UD4 v2.0 @ F14
    Core i5 760 @ 20 x 201, 4.02GHz
    TRUE Black with a single Noctua NF-P12 pumping out 55 CFM @ 19db .
    2 x 2GB Mushkin Ridgeback (996902), @ 7-10-8-27, 2010-DDR, 1.66v
    2 x Gigabyte GTX 460 1024MB in SLI (Pre OC'd to 715MHz core and 1800MHz VRAM) @ 850 Core / 4100 Mem.
    Intel X25-M Boot Drive (OS and Programs) 200MB/s Read & 90MB/s Write
    Corsair X32 200MB/s Read & 100MB/s Write
    WD Caviar Blue 640GB C (Steam, Games, Storage, Temp Files & Folders, etc)
    Samsung F3 500GB Backup/Images
    Noctua 1300RPM 19dB case fan (rear extraction)
    3 x 140 MM Coolermaster LED fans (one front intake, one top extraction, one side intake)
    Dell Ultra Sharp 2209WAf E-IPS @ 1680x1050

  2. #32
    Join Date
    Mar 2008
    Location
    Brisbane, Australia
    Posts
    79

    Default Re: G.Skill memory for EP45-UD3P

    My cooling is good (Xigmatec S1283), during IntelBurnTest maximum stress gets both cores to 57 degrees. Needed 1.29375v in the BIOS to get to 3.78Ghz, actual (CPU-Z) is 1.248v and under load 1.232v so I guess vdroop is 0.016v. I've heard LLC is not good for 45nm precessors?, I don't know, I'm no expert. I have it disabled.

    <!-- / message --><!-- sig -->
    (1) Gigabyte 3DAurora chassis - Gigabyte Ex38-DS4 - Xeon 3110 - Zalman CNPS9500 LED - 2x1GB PC2 8500 Crucial Ballistix Tracer 2.0v (BL12864AL106A) - ThermalTake Cyclo RAM cooler - 2xMSI Radeon HD4670 - Corsair HX 620W - WD 36GB Raptor - Seagate 250GB (ST3250310AS) - Asus DRW 2014LIT - XP Pro SP3 (32bit)
    (2) NZXT Apollo chassis - Gigabyte EP45-UD3P - E8400 - Xigmatek S1283 Red Scorpion - 2x2GB PC2 8800 G.Skill 1.9v (F2-8800CL5D-4GBPI) - Gigabyte GeForce 9600GT - Corsair HX 520W - Seagate 250GB (ST3250318AS) - LG DRW GH22NP20 - XP Pro SP3 (32bit)

  3. #33
    kick's Avatar
    kick is offline Senior Member
    Join Date
    Feb 2009
    Location
    Europe,the wild wild west.
    Posts
    1,223

    Default Re: G.Skill memory for EP45-UD3P

    the llc enabled "problem"is supposedly to do with earlier ep45 mbrds giving voltage spikes at lower cpu loadings.
    In practice I go for whatever will hold the cpu closest to what I set it at in bios while cpu is loaded.
    For me thats what I posted above.. I still get vdroop but not as extreme as without llc enabled.
    Some people say you get better results at a few mhz diff with llc enabled or not,but hey if I changed every setting every time i tried a different speed,Id never actually get to use my pc
    edit ive tried intel burn.psycho has too.
    I got near 80C under load,indicated with 10 + passes for the cores but I dont know how much of a system check it is.It really seems to heat up the cpu and sounds scary,but feels more like"hey wanna see how hot your cpu will get and still run ok program"
    nb while im typing this Im 50 min into an OCCT 1hr test
    peak 69 core 0/overall cpu temp peak=57/system=41C/northbridge= 39C/gpu=46C//room temp showing 20 C/70 f.

    yeh too much v is supposed to be the main component killer and then temperature.

    test finished..ill try n save the graph readings.
    Last edited by kick; 05-10-2009 at 08:56 AM.
    Current Systems:

    Asrock p67 Extreme6.............. Gigabyte EP-45 UD3 ...................... Gigabyte 73 PVM S2
    Intel i5 2500k 4.8ghz................ Intel Q8400 3.8ghz......................... Intel D820 2.8ghz
    Zalman 10x cooler.................... Coolermaster V8............................ HP cooler
    8GB Gskill ripjaw ddr3.............. 4GB Gskill PI ddr2.......................... 4GB samsung ddr2
    60GB ssd/500GB HDD .............. WD 1TB hdd.................................... Seagate 160GB hdd
    GTX 460 1GB x2 SLI ................. Msi 9600GT 512MB(died) ........... Onboard gx
    Win7 64 ,750w psu(ocz)............ Win7 64 ,520w psu,seasonic...... Win XP pro ,400w psu

    HEC 6A34 case . ....................... Jeantec R2 case............................ Packard Bell case

    hoping to upgrade to http://www.thinkgeek.com/stuff/41/habicase.shtml
    http://www.flixya.com/video/140325/Animal-launching

  4. #34
    Join Date
    Apr 2009
    Location
    J'Habite En Angleterre
    Posts
    2,431

    Default Re: G.Skill memory for EP45-UD3P

    LLC doesn't really do much harm. As a rule, if you can get a stable CPU without using it, up to 1.4v, don't use it. If you can't get stable at 1.4v, try 1.3500v and upward with it on. It would be really pointless to use if you can get stable without it on 1.3625v or less. Though you do see a fair few with it on, and running something like 1.2xxv.

    As is usual with the internet, people seem to think in black and white. Once something is mentioned once, it can be taken as fact, and is then parroted by everyone on all sorts of forums and articles. things like "vdroop is evil, eliminate it before it assaults your wife and eats your babies", and the new in vogue "Using LLC or more than 1.4v CPU Termination will instantly and magically cause your CPU to degrade rapidly or even blow up".

    As usual, the truth is somewhere in the middle.

    You're much more likely to kill a CPU with high CPU Termination voltage than with LLC, that is true but I really do wonder who plucked the "No more than 1.4v VTT" thing out of their arse though. So anandtech killed a CPU... who cares, they must have been giving it some monster voltages all round for that to happen. If you need it to have the clock speed you want, and temperatures don't exceed 70c then it's all good, as long as you're sensible and don't go too far.
    Coolermaster CM 690 II advance Case
    Corsair HX750 (CWT, 91%(80+ Gold rated @230V) single 62A 12V rail
    P55A-UD4 v2.0 @ F14
    Core i5 760 @ 20 x 201, 4.02GHz
    TRUE Black with a single Noctua NF-P12 pumping out 55 CFM @ 19db .
    2 x 2GB Mushkin Ridgeback (996902), @ 7-10-8-27, 2010-DDR, 1.66v
    2 x Gigabyte GTX 460 1024MB in SLI (Pre OC'd to 715MHz core and 1800MHz VRAM) @ 850 Core / 4100 Mem.
    Intel X25-M Boot Drive (OS and Programs) 200MB/s Read & 90MB/s Write
    Corsair X32 200MB/s Read & 100MB/s Write
    WD Caviar Blue 640GB C (Steam, Games, Storage, Temp Files & Folders, etc)
    Samsung F3 500GB Backup/Images
    Noctua 1300RPM 19dB case fan (rear extraction)
    3 x 140 MM Coolermaster LED fans (one front intake, one top extraction, one side intake)
    Dell Ultra Sharp 2209WAf E-IPS @ 1680x1050

  5. #35

    Default Re: G.Skill memory for EP45-UD3P

    I had a E8400 that started to lose it's overclock with 1.4+. I know one incident isn't a trend, but, I've read others posts who reported the same thing. It is not "out of someone's arse"
    i7 3770K, 47X100= 4.7GHz at 1.33V, ASROCK Z77 Extreme4, 2 X 4GB Patriot Viper Black Maba DDR3 1600, GTX 590, 2 X Corsair Force 3 120GB SSDs in RAID 0, Barracuda SATA 7200.10 500GB, Barracuda SATA 7200.11 1000GB Back Ups, OCZ ZX 1250W, Z-5500s, LG Blu Ray Player/DVD Burner, Koolance CTR-CD12 Fan/Pump Controller, Windows 7 X64 Professional, HAF X. Vision Quest 24" WS LCD, Optoma H66 Projector
    Cooling: Thermochill PA120.2 GT AP15 in push, DDC 3.25/XSPC Res top, Apogee Xt Extreme, XSPC Razor, Coolgate CG-240 Swiftech Helix in push/pull, MCP35X.

  6. #36
    Join Date
    Mar 2008
    Location
    Brisbane, Australia
    Posts
    79

    Default Re: G.Skill memory for EP45-UD3P

    Here are my current settings. All stress testing looks OK; Prime95 small FFTs 13.5 hours stable, Prime95 Blend 12 hours stable, IntelBurnTest 40 passes stable; but I still get memtest86+ errors. Simple answer is dodgy memory but it could be a memory timing or some other issue. As you can see I have all the subtimings on Auto. I have also included the actual values these get set to (see memset pic).

    Code:
    Robust Graphics Booster ...............: [Auto]
    CPU Clock Ratio .......................: [ 8]
    Fine CPU Clock Ratio...................: [+0.5]
    CPU Frequency .........................: 3.78GHz (445x8.5)
     
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control.................: [Enabled] 
    CPU Host Frequency (Mhz) ..............: [445Mhz]
    PCI Express Frequency (Mhz) ...........: [100]
     
    C.I.A.2 ...............................: [Disabled]
     
    Advanced Clock Control [Press Enter]
    CPU Clock Drive........................: [800mV]
    PCI Express Clock Drive................: [900mV]
    CPU Clock Skew (ps)....................:   [0ps]
    MCH Clock Skew (ps)....................:   [0ps]
     
    DRAM Performance Control
    Performance Enhance....................: [STANDARD]
    Extreme Memory Profile (X.M.P.)........: [Disabled]
    (G)MCH Frequency Latch.................: [Auto]
    System Memory Multiplier ..............: [2.40B] 
    Memory Frequency (Mhz) ................: [1068]
    DRAM Timing Selectable ................: [Manual]
     
    Standard Timing Control
    CAS Latency Time.......................:  [5]
    tRCD ..................................:  [5]
    tRP....................................:  [5]
    tRAS...................................:  [15]
     
    Advanced Timing Control
    tRRD...................................:  [Auto]
    tWTR...................................:  [Auto]
    tWR....................................:  [Auto]
    tRFC...................................:  [Auto]
    tRTP...................................:  [Auto]
    Command Rate (CMD) ....................:  [Auto]
     
    Driving Strength Profiles
    Driving Strength ......................: [1066]
     
    Channel A
    Static tRead Value.....................: [Auto]
    tRD Phase0 Adjustment..................: [Auto]
    tRD Phase1 Adjustment..................: [Auto]
    tRD Phase2 Adjustment .................: [Auto]
    tRD Phase3 Adjustment..................: [Auto]
     
    Trd2rd(Different Rank).................: [Auto]
    Twr2wr(Different Rank).................: [Auto]
    Twr2rd(Different Rank).................: [Auto]
    Trd2wr(Same/Diff Rank).................: [Auto]
     
    Dimm1 Clock Skew Control...............: [Auto]
    Dimm2 Clock Skew Control...............: [Auto]
    DDR Write Training.....................: [Auto]
     
    Channel B
    Static tRead Value.....................: [Auto]
    tRD Phase0 Adjustment..................: [Auto]
    tRD Phase1 Adjustment..................: [Auto]
    tRD Phase2 Adjustment .................: [Auto]
    tRD Phase3 Adjustment..................: [Auto]
     
    Trd2rd(Different Rank).................: [Auto]
    Twr2wr(Different Rank).................: [Auto]
    Twr2rd(Different Rank).................: [Auto]
    Trd2wr(Same/Diff Rank).................: [Auto]
     
    Dimm1 Clock Skew Control...............: [Auto]
    Dimm2 Clock Skew Control...............: [Auto]
    DDR Write Training.....................: [Auto]
     
    Motherboard Voltage Control
     
    CPU---------------------Normal-----------Current
     
    Load Line Calibration..................: [Disabled]
    CPU Vcore...............1.30000V.......: [1.29375V]
    CPU Termination.........1.200V.........: [1.220V]
    CPU PLL.................1.500V.........: [1.500V]
    CPU Reference...........0.760V.........: [0.772V]  
     
    MCH/ICH
    MCH Core................1.100V.........: [1.240V]
    MCH Reference...........0.760V.........: [0.772V]
    MCH/DRAM Reference......0.900V.........: [0.900V]
    ICH I/O.................1.500V.........: [1.500V]
    ICH Core................1.100V.........: [1.100V]
     
    DRAM
    DRAM Voltage............1.800V.........: [1.900V ]
    DRAM Termination........0.900V.........: [0.900V]
    Channel A Reference.....0.900V.........: [0.900V]
    Channel B Reference.....0.900V.........: [0.900V]
     
    Advanced Settings
    Limit CPUID Max. to 3..................: [Disabled]
    No-Execute Memory Protect..............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Enabled]
    C2/C2E State Support...................: [Disabled]
    x C4/C4E State Support.................: [Disabled]
    CPU Thermal Monitor 2(TM2) ............: [Enabled]
    CPU EIST Function......................: [Disabled]
    Virtualization Technology..............: [Disabled]
     
    Integrated Peripherals
    USB Storage Fucntion .............: [Disabled]
    Attachment 1063
    (1) Gigabyte 3DAurora chassis - Gigabyte Ex38-DS4 - Xeon 3110 - Zalman CNPS9500 LED - 2x1GB PC2 8500 Crucial Ballistix Tracer 2.0v (BL12864AL106A) - ThermalTake Cyclo RAM cooler - 2xMSI Radeon HD4670 - Corsair HX 620W - WD 36GB Raptor - Seagate 250GB (ST3250310AS) - Asus DRW 2014LIT - XP Pro SP3 (32bit)
    (2) NZXT Apollo chassis - Gigabyte EP45-UD3P - E8400 - Xigmatek S1283 Red Scorpion - 2x2GB PC2 8800 G.Skill 1.9v (F2-8800CL5D-4GBPI) - Gigabyte GeForce 9600GT - Corsair HX 520W - Seagate 250GB (ST3250318AS) - LG DRW GH22NP20 - XP Pro SP3 (32bit)

  7. #37
    Join Date
    Apr 2009
    Location
    J'Habite En Angleterre
    Posts
    2,431

    Default Re: G.Skill memory for EP45-UD3P

    I stand by my statement. It most certainly, in its usual form, which is over hyped and exagerated: "pulled out of their arse". I have personally experienced no CPU degredation.

    there have been cases where after a certain period of time, people have had to give a chip more voltage to maintain a certain core speed. Now is that the CPU? Is it a deterioration of motherboard components? Is it merely that someone set a large overclock in the winter with lower ambient temperatures, and come along with summer came instability.

    These such variables are never mentioned. It's usually pure conjecture and an over excited overclocker shouting "Aaaagh! YOOT-WANID" (It Used To Work And Now It Doesn't). And when someone reasonably suggests that an increase in CPU temperature can cause a lesser overclock, even if that increase means the processor temp is still in the "safe zone", they still insist that the degredation fairy definately did it, because they saw it fleeing the scene.

    The odds of your processor going **** up are worse than someone winning the lottery, and the brittish lottery jackpot odds are 14 million to 1.

    And by the way, I'm talking reasonable voltages here, not someone using a five stage phase change cascade and pumping 1.8v through the thing. If their chip "degrades" then it's their own fault, and I'm sure they fully understand the risks involved anyway.
    Last edited by Psycho101; 05-10-2009 at 11:49 AM.
    Coolermaster CM 690 II advance Case
    Corsair HX750 (CWT, 91%(80+ Gold rated @230V) single 62A 12V rail
    P55A-UD4 v2.0 @ F14
    Core i5 760 @ 20 x 201, 4.02GHz
    TRUE Black with a single Noctua NF-P12 pumping out 55 CFM @ 19db .
    2 x 2GB Mushkin Ridgeback (996902), @ 7-10-8-27, 2010-DDR, 1.66v
    2 x Gigabyte GTX 460 1024MB in SLI (Pre OC'd to 715MHz core and 1800MHz VRAM) @ 850 Core / 4100 Mem.
    Intel X25-M Boot Drive (OS and Programs) 200MB/s Read & 90MB/s Write
    Corsair X32 200MB/s Read & 100MB/s Write
    WD Caviar Blue 640GB C (Steam, Games, Storage, Temp Files & Folders, etc)
    Samsung F3 500GB Backup/Images
    Noctua 1300RPM 19dB case fan (rear extraction)
    3 x 140 MM Coolermaster LED fans (one front intake, one top extraction, one side intake)
    Dell Ultra Sharp 2209WAf E-IPS @ 1680x1050

  8. #38

    Default Re: G.Skill memory for EP45-UD3P

    Quote Originally Posted by dclayw View Post
    Here are my current settings. All stress testing looks OK; Prime95 small FFTs 13.5 hours stable, Prime95 Blend 12 hours stable, IntelBurnTest 40 passes stable; but I still get memtest86+ errors. Simple answer is dodgy memory but it could be a memory timing or some other issue. As you can see I have all the subtimings on Auto. I have also included the actual values these get set to (see memset pic).

    Code:
    Robust Graphics Booster ...............: [Auto]
    CPU Clock Ratio .......................: [ 8]
    Fine CPU Clock Ratio...................: [+0.5]
    CPU Frequency .........................: 3.78GHz (445x8.5)
     
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control.................: [Enabled] 
    CPU Host Frequency (Mhz) ..............: [445Mhz]
    PCI Express Frequency (Mhz) ...........: [100]
     
    C.I.A.2 ...............................: [Disabled]
     
    Advanced Clock Control [Press Enter]
    CPU Clock Drive........................: [800mV]
    PCI Express Clock Drive................: [900mV]
    CPU Clock Skew (ps)....................:   [0ps]
    MCH Clock Skew (ps)....................:   [0ps]
     
    DRAM Performance Control
    Performance Enhance....................: [STANDARD]
    Extreme Memory Profile (X.M.P.)........: [Disabled]
    (G)MCH Frequency Latch.................: [Auto]
    System Memory Multiplier ..............: [2.40B] 
    Memory Frequency (Mhz) ................: [1068]
    DRAM Timing Selectable ................: [Manual]
     
    Standard Timing Control
    CAS Latency Time.......................:  [5]
    tRCD ..................................:  [5]
    tRP....................................:  [5]
    tRAS...................................:  [15]
     
    Advanced Timing Control
    tRRD...................................:  [Auto]
    tWTR...................................:  [Auto]
    tWR....................................:  [Auto]
    tRFC...................................:  [Auto]
    tRTP...................................:  [Auto]
    Command Rate (CMD) ....................:  [Auto]
     
    Driving Strength Profiles
    Driving Strength ......................: [1066]
     
    Channel A
    Static tRead Value.....................: [Auto]
    tRD Phase0 Adjustment..................: [Auto]
    tRD Phase1 Adjustment..................: [Auto]
    tRD Phase2 Adjustment .................: [Auto]
    tRD Phase3 Adjustment..................: [Auto]
     
    Trd2rd(Different Rank).................: [Auto]
    Twr2wr(Different Rank).................: [Auto]
    Twr2rd(Different Rank).................: [Auto]
    Trd2wr(Same/Diff Rank).................: [Auto]
     
    Dimm1 Clock Skew Control...............: [Auto]
    Dimm2 Clock Skew Control...............: [Auto]
    DDR Write Training.....................: [Auto]
     
    Channel B
    Static tRead Value.....................: [Auto]
    tRD Phase0 Adjustment..................: [Auto]
    tRD Phase1 Adjustment..................: [Auto]
    tRD Phase2 Adjustment .................: [Auto]
    tRD Phase3 Adjustment..................: [Auto]
     
    Trd2rd(Different Rank).................: [Auto]
    Twr2wr(Different Rank).................: [Auto]
    Twr2rd(Different Rank).................: [Auto]
    Trd2wr(Same/Diff Rank).................: [Auto]
     
    Dimm1 Clock Skew Control...............: [Auto]
    Dimm2 Clock Skew Control...............: [Auto]
    DDR Write Training.....................: [Auto]
     
    Motherboard Voltage Control
     
    CPU---------------------Normal-----------Current
     
    Load Line Calibration..................: [Disabled]
    CPU Vcore...............1.30000V.......: [1.29375V]
    CPU Termination.........1.200V.........: [1.220V]
    CPU PLL.................1.500V.........: [1.500V]
    CPU Reference...........0.760V.........: [0.772V]  
     
    MCH/ICH
    MCH Core................1.100V.........: [1.240V]
    MCH Reference...........0.760V.........: [0.772V]
    MCH/DRAM Reference......0.900V.........: [0.900V]
    ICH I/O.................1.500V.........: [1.500V]
    ICH Core................1.100V.........: [1.100V]
     
    DRAM
    DRAM Voltage............1.800V.........: [1.900V ]
    DRAM Termination........0.900V.........: [0.900V]
    Channel A Reference.....0.900V.........: [0.900V]
    Channel B Reference.....0.900V.........: [0.900V]
     
    Advanced Settings
    Limit CPUID Max. to 3..................: [Disabled]
    No-Execute Memory Protect..............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Enabled]
    C2/C2E State Support...................: [Disabled]
    x C4/C4E State Support.................: [Disabled]
    CPU Thermal Monitor 2(TM2) ............: [Enabled]
    CPU EIST Function......................: [Disabled]
    Virtualization Technology..............: [Disabled]
     
    Integrated Peripherals
    USB Storage Fucntion .............: [Disabled]
    Attachment 1063
    Try Disabling CPU Enhanced Halt (C1E). After that, bump up CPU voltage another +.01V.
    <<< LGA2011 System Summary >>>
    > Power Supply: CORSAIR AX Series AX860 860W 80 PLUS PLATINUM Haswell Ready Full Modular (NE Link)
    > Chipset : Intel X99
    > Mainboard :Gigabyte GA-X99-Ultra Gaming
    (NE Link)
    > Processor : i7-6850K (NE Link)
    > AIO: Corsair Hydro Series H100i V2 (NE Link)
    > Physical Memory : G.SKILL TridentZ Series 32GB (4 x 8GB) DDR4 3200 Model F4-3200C14Q-32GTZSW (NE Link)
    > Video Card : 2x ASUS ROG STRIX-GTX1070-O8G-GAMING (NE Link)


    <<< LGA1366 System Summary >>>
    > Power Supply:
    >>>Original PSU (2011-01) :
    Corsair 620HX (NE Link)
    >>>Upgrade PSU (2012-01) : CORSAIR AX850 (CMPSU-850AX) 850W (NE Link)
    > Chipset : Intel X58
    > Mainboard : Gigabyte GA-X58A-UD3R (REV.2.0) (FB BIOS)
    (NE Link MPP Link)
    > Processor : i7-950 (Revision D0) 3.0GHz @3.84GHz
    (NE Link MPP Link)
    > HSF:
    Noctua NH-D14 (NE Link MPP Link)
    > Physical Memory :
    >>>Original RAM (2011-01) : G.SKILL 6GB (3 x 2GB) 240-Pin DDR3 1600 (PC3 12800) Model F3-12800CL9T-6GBNQ
    >>>Upgrade RAM (2012-01) : Mushkin Enhanced Blackline 12GB (3 x 4GB) 240-Pin DDR3 2000 (PC3 16000) w/FrostByte Heatsink Model 998990 (NE Link MPP Link OverClockersClub Dot Com Article)
    > Video Card :
    >>>Original Vid Card (2011-01) : BFG Geforce GTX295 (
    NE Link)
    >>>Upgrade Vid Card(2012-01) : (2) EVGA 02G-P3-1568-KR GTX 560 Ti (2GB)-SLI (
    NE Link)
    >>>Upgrade Vid Card(2013-07) : (2) GTX 760-SLI Gigabyte GV-N760OC-4GB (NE Link)
    > DVD-Rom Drive : TSSTcorp CDDVDW SH-S203B ATA Device
    > Monitor :
    ViewSonic Pro Series VP2655wb Black 26" (
    NE Link)
    > Operating System : Windows 7 Ultimate
    > Case : COOLER MASTER HAF X RC-942-KKN1 Black Steel (
    NE Link)

    <<< LGA775 System Summary >>>
    > Power Supply: Corsair 620HX (
    NE Link)
    > Mainboard : Gigabyte P35-S3G (F2 BIOS)
    > Chipset : Intel P35
    > Processor : Core 2 Duo E8400 Wolfdale (Revision C0) 3.0GHz @ 3950 MHz
    > HSF: Arctic Cooling Freezer 7 Pro
    > Physical Memory : CORSAIR DOMINATOR 4GB (2 x 2GB) (
    Link)
    > Video Card : BFG Geforce GTX295
    > DVD-Rom Drive : TSSTcorp CDDVDW SH-S203B ATA Device
    >
    Monitor : ViewSonic Pro Series VP2655wb Black 26"
    > Operating System : Windows 7 Ultimate


  9. #39
    kick's Avatar
    kick is offline Senior Member
    Join Date
    Feb 2009
    Location
    Europe,the wild wild west.
    Posts
    1,223

    Default Re: G.Skill memory for EP45-UD3P

    No real experience of o/c dual cores(aside from my D820 which is more 2 p4's stuck together and no seperate core readings).

    Is 1.30v the processor VID?
    Seems stable enough altho the memory secondary timings do seem very "loose".
    Who cares on that tho if the bandwidth is good. Did you do any bandwidth tests/comparisons with the memory at different settings?
    Current Systems:

    Asrock p67 Extreme6.............. Gigabyte EP-45 UD3 ...................... Gigabyte 73 PVM S2
    Intel i5 2500k 4.8ghz................ Intel Q8400 3.8ghz......................... Intel D820 2.8ghz
    Zalman 10x cooler.................... Coolermaster V8............................ HP cooler
    8GB Gskill ripjaw ddr3.............. 4GB Gskill PI ddr2.......................... 4GB samsung ddr2
    60GB ssd/500GB HDD .............. WD 1TB hdd.................................... Seagate 160GB hdd
    GTX 460 1GB x2 SLI ................. Msi 9600GT 512MB(died) ........... Onboard gx
    Win7 64 ,750w psu(ocz)............ Win7 64 ,520w psu,seasonic...... Win XP pro ,400w psu

    HEC 6A34 case . ....................... Jeantec R2 case............................ Packard Bell case

    hoping to upgrade to http://www.thinkgeek.com/stuff/41/habicase.shtml
    http://www.flixya.com/video/140325/Animal-launching

  10. #40
    Join Date
    Mar 2008
    Location
    Brisbane, Australia
    Posts
    79

    Default Re: G.Skill memory for EP45-UD3P

    Quote Originally Posted by Bee_Dee_3_Dee View Post
    Try Disabling CPU Enhanced Halt (C1E). After that, bump up CPU voltage another +.01V.
    Thanks for the suggestion, I'll give that a go.
    (1) Gigabyte 3DAurora chassis - Gigabyte Ex38-DS4 - Xeon 3110 - Zalman CNPS9500 LED - 2x1GB PC2 8500 Crucial Ballistix Tracer 2.0v (BL12864AL106A) - ThermalTake Cyclo RAM cooler - 2xMSI Radeon HD4670 - Corsair HX 620W - WD 36GB Raptor - Seagate 250GB (ST3250310AS) - Asus DRW 2014LIT - XP Pro SP3 (32bit)
    (2) NZXT Apollo chassis - Gigabyte EP45-UD3P - E8400 - Xigmatek S1283 Red Scorpion - 2x2GB PC2 8800 G.Skill 1.9v (F2-8800CL5D-4GBPI) - Gigabyte GeForce 9600GT - Corsair HX 520W - Seagate 250GB (ST3250318AS) - LG DRW GH22NP20 - XP Pro SP3 (32bit)

Page 4 of 5 FirstFirst ... 2345 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •