Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 6 of 7 FirstFirst ... 4567 LastLast
Results 51 to 60 of 64

Thread: GA-EP45-UD3P + 4GB/8GB Corsair Dominator DDR2 1066 Intermittent Problems




  1. #51
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: GA-EP45-UD3P + 4GB/8GB Corsair Dominator DDR2 1066 Intermittent Problems

    Quote Originally Posted by Chike View Post
    9.5 lol
    Thats what I mean, a 9 instead of an 8... lol for 9.5 instead of 8.5 I might need to look at mine again...

  2. #52
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: GA-EP45-UD3P + 4GB/8GB Corsair Dominator DDR2 1066 Intermittent Problems

    My bad I tought it was the Q9950 instead of the E8500. I'd put the Q9550 in the UD3P...

  3. #53
    Join Date
    Nov 2008
    Location
    Hu3zil
    Posts
    64

    Default Re: GA-EP45-UD3P + 4GB/8GB Corsair Dominator DDR2 1066 Intermittent Problems

    Try these settings below. I have 4 dimms installed, Corsair Dominator too.

    Please see if your sticks is all the same revision, if mixed, bad things happen, like your PC cannot post, happened with me, spent a lot of money because of this.

    Code:
     
    > MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 9x
    Fine CPU Clock Ratio.....................:.+0.5
    CPU Frequency ...........................: 3.16GHz( 333x9.5)
     
     
    >> Clock Chip Control
    >>>>> Standard Clock Control
    CPU Host Clock Control.................: [ENABLED]
    CPU Host Frequency (Mhz) ..............: 333 Mhz
    PCI Express Frequency (Mhz) ...........: 100
     
    C.I.A.2 ...............................:[Disabled]
     
    >>>>> Advanced Clock Control
    > Advanced Clock Control [Press Enter]
    CPU Clock Drive........................: 800mV
    PCI Express Clock Drive................: 900mV
    CPU Clock Skew (ps)....................: 0ps
    MCH Clock Skew (ps)....................: 0ps
     
     
    >> DRAM Performance Control
    Performance Enhance....................: [STANDARD]
    Extreme Memory Profile (X.M.P.)........: [PROFILE 2] Or whatever is there
    (G)MCH Frequency Latch.................: [333Mhz]
    System Memory Multiplier ..............: [3.20B]
    Memory Frequency (Mhz) ................: 1066
    DRAM Timing Selectable ................: [Manual]
     
    >>>>> Standard Timing Control
    CAS Latency Time.......................: 5 [ 5]
    tRCD ..................................: 7 [ 5]
    tRP'...................................: 7 [ 5]
    tRAS...................................: 24 [ 15]
     
    Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go
     
    >>>>> Advanced Timing Control
    > Advanced Timing Control [Press Enter]
    tRRD...................................: 4 [ AUTO]
    tWTR...................................: 4 [ AUTO]
    tWR....................................: 8 [ AUTO]
    tRFC...................................: 68 [ AUTO]
    tRTP...................................: 4 [ AUTO]
    Command Rate (CMD) ....................: 0 [0]
     
    Channel A
    Driving Strength ......................: [1066MHz]
     
    Static tRead Value.....................: 8 [ AUTO]
    tRD Phase0 Adjustment..................: 0 [Auto] <<< Leave for all below as well
    tRD Phase1 Adjustment..................: 0 [Auto]
    tRD Phase2 Adjustment ................: 0 [Auto]
    tRD Phase3 Adjustment.................: 0 [Auto]
    Trd2rd(Different Rank).................: 8 [Auto]
    Twr2wr(Different Rank).................: 8 [Auto]
    Twr2rd(Different Rank).................: 7 [Auto]
    Trd2wr(Same/Diff Rank).................: 9 [Auto]
    Dimm1 Clock Skew Control...............: [Auto]
    Dimm2 Clock Skew Control...............: [Auto]
     
    Channel B
    Driving Strength ......................: [1066MHz]
     
    Static tRead Value.....................: 8 [ AUTO]
    tRD Phase0 Adjustment..................: 0 [Auto] <<< Leave for all below as well
    tRD Phase1 Adjustment..................: 0 [Auto]
    tRD Phase2 Adjustment ................: 0 [Auto]
    tRD Phase3 Adjustment.................: 0 [Auto]
    Trd2rd(Different Rank).................: 8 [Auto]
    Twr2wr(Different Rank).................: 8 [Auto]
    Twr2rd(Different Rank).................: 7 [Auto]
    Trd2wr(Same/Diff Rank).................: 9 [Auto]
    Dimm1 Clock Skew Control...............: [Auto]
    Dimm2 Clock Skew Control...............: [Auto]
     
    > Motherboard Voltage Control
    >>> CPU
    Load-Line Calibration..................: [ENABLED]
    CPU Vcore..............................: 1.18750V [NORMAL]
    CPU Termination........................: 1.200V [NORMAL] << If overclocking Please set to stock, Auto overvolts this way to much. Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore. Auto is fine if not overclocking
    CPU PLL................................: 1.500V [NORMAL] << If overclocking Please set to stock, Auto overvolts this way to much. Optimal range for overclock would be 1.5-1.65. Auto is fine if not overclocking
     
    CPU Reference..........................: 0.760V [AUTO] << .64% Of Vtt (Termination above) Auto Will set this correctly
    >>> MCH/ICH
    MCH Core...............................: 1.100V [1.260V]
    MCH Reference..........................: 0.760V [AUTO]
    MCH/DRAM Ref...........................: 0.900V [AUTO]
    ICH I/O................................: 1.500V [AUTO]
    ICH Core...............................: 1.100V [AUTO]
     
    >>> DRAM
    DRAM Voltage...........................: 1.800V [2.100V]
    DRAM Termination.......................: 0.900V [AUTO] << Leave
    Channel A Reference 0.900V.............: 0.900V [AUTO] << Leave
    Channel B Reference 0.900V.............: 0.900V [AUTO] << Leave
     
    > Advanced BIOS Features
    Limit CPUID Max. to 3..................: [Disabled]
    No-Execute Memory Protect..............: [Enabled]
    CPU Enhanced Halt (C1E)................: [ENABLED]
    C2/C2E State Support...................: [Disabled]
    x C4/C4E State Support.................: [Disabled]
    CPU Thermal Monitor 2(TM2) ............: [Enabled]
    CPU EIST Function......................: [Disabled]
    Virtualization Technology..............: [Disabled] << Enabled if you use Vmware/Virtual PC
     
    > Integrated Peripherals
    Legacy USB Storage Detect .............: [Disabled] << *Note* Must be enabled to flash from USB

  4. #54
    Join Date
    May 2009
    Posts
    28

    Default Re: GA-EP45-UD3P + 4GB/8GB Corsair Dominator DDR2 1066 Intermittent Problems

    Quote Originally Posted by AHPD View Post
    Try these settings below. I have 4 dimms installed, Corsair Dominator too.

    Please see if your sticks is all the same revision, if mixed, bad things happen, like your PC cannot post, happened with me, spent a lot of money because of this.

    Code:
     
    > MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 9x
    Fine CPU Clock Ratio.....................:.+0.5
    CPU Frequency ...........................: 3.16GHz( 333x9.5)
     
     
    >> Clock Chip Control
    >>>>> Standard Clock Control
    CPU Host Clock Control.................: [ENABLED]
    CPU Host Frequency (Mhz) ..............: 333 Mhz
    PCI Express Frequency (Mhz) ...........: 100
     
    C.I.A.2 ...............................:[Disabled]
     
    >>>>> Advanced Clock Control
    > Advanced Clock Control [Press Enter]
    CPU Clock Drive........................: 800mV
    PCI Express Clock Drive................: 900mV
    CPU Clock Skew (ps)....................: 0ps
    MCH Clock Skew (ps)....................: 0ps
     
     
    >> DRAM Performance Control
    Performance Enhance....................: [STANDARD]
    Extreme Memory Profile (X.M.P.)........: [PROFILE 2] Or whatever is there
    (G)MCH Frequency Latch.................: [333Mhz]
    System Memory Multiplier ..............: [3.20B]
    Memory Frequency (Mhz) ................: 1066
    DRAM Timing Selectable ................: [Manual]
     
    >>>>> Standard Timing Control
    CAS Latency Time.......................: 5 [ 5]
    tRCD ..................................: 7 [ 5]
    tRP'...................................: 7 [ 5]
    tRAS...................................: 24 [ 15]
     
    Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go
     
    >>>>> Advanced Timing Control
    > Advanced Timing Control [Press Enter]
    tRRD...................................: 4 [ AUTO]
    tWTR...................................: 4 [ AUTO]
    tWR....................................: 8 [ AUTO]
    tRFC...................................: 68 [ AUTO]
    tRTP...................................: 4 [ AUTO]
    Command Rate (CMD) ....................: 0 [0]
     
    Channel A
    Driving Strength ......................: [1066MHz]
     
    Static tRead Value.....................: 8 [ AUTO]
    tRD Phase0 Adjustment..................: 0 [Auto] <<< Leave for all below as well
    tRD Phase1 Adjustment..................: 0 [Auto]
    tRD Phase2 Adjustment ................: 0 [Auto]
    tRD Phase3 Adjustment.................: 0 [Auto]
    Trd2rd(Different Rank).................: 8 [Auto]
    Twr2wr(Different Rank).................: 8 [Auto]
    Twr2rd(Different Rank).................: 7 [Auto]
    Trd2wr(Same/Diff Rank).................: 9 [Auto]
    Dimm1 Clock Skew Control...............: [Auto]
    Dimm2 Clock Skew Control...............: [Auto]
     
    Channel B
    Driving Strength ......................: [1066MHz]
     
    Static tRead Value.....................: 8 [ AUTO]
    tRD Phase0 Adjustment..................: 0 [Auto] <<< Leave for all below as well
    tRD Phase1 Adjustment..................: 0 [Auto]
    tRD Phase2 Adjustment ................: 0 [Auto]
    tRD Phase3 Adjustment.................: 0 [Auto]
    Trd2rd(Different Rank).................: 8 [Auto]
    Twr2wr(Different Rank).................: 8 [Auto]
    Twr2rd(Different Rank).................: 7 [Auto]
    Trd2wr(Same/Diff Rank).................: 9 [Auto]
    Dimm1 Clock Skew Control...............: [Auto]
    Dimm2 Clock Skew Control...............: [Auto]
     
    > Motherboard Voltage Control
    >>> CPU
    Load-Line Calibration..................: [ENABLED]
    CPU Vcore..............................: 1.18750V [NORMAL]
    CPU Termination........................: 1.200V [NORMAL] << If overclocking Please set to stock, Auto overvolts this way to much. Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore. Auto is fine if not overclocking
    CPU PLL................................: 1.500V [NORMAL] << If overclocking Please set to stock, Auto overvolts this way to much. Optimal range for overclock would be 1.5-1.65. Auto is fine if not overclocking
     
    CPU Reference..........................: 0.760V [AUTO] << .64% Of Vtt (Termination above) Auto Will set this correctly
    >>> MCH/ICH
    MCH Core...............................: 1.100V [1.260V]
    MCH Reference..........................: 0.760V [AUTO]
    MCH/DRAM Ref...........................: 0.900V [AUTO]
    ICH I/O................................: 1.500V [AUTO]
    ICH Core...............................: 1.100V [AUTO]
     
    >>> DRAM
    DRAM Voltage...........................: 1.800V [2.100V]
    DRAM Termination.......................: 0.900V [AUTO] << Leave
    Channel A Reference 0.900V.............: 0.900V [AUTO] << Leave
    Channel B Reference 0.900V.............: 0.900V [AUTO] << Leave
     
    > Advanced BIOS Features
    Limit CPUID Max. to 3..................: [Disabled]
    No-Execute Memory Protect..............: [Enabled]
    CPU Enhanced Halt (C1E)................: [ENABLED]
    C2/C2E State Support...................: [Disabled]
    x C4/C4E State Support.................: [Disabled]
    CPU Thermal Monitor 2(TM2) ............: [Enabled]
    CPU EIST Function......................: [Disabled]
    Virtualization Technology..............: [Disabled] << Enabled if you use Vmware/Virtual PC
     
    > Integrated Peripherals
    Legacy USB Storage Detect .............: [Disabled] << *Note* Must be enabled to flash from USB
    I tried those settings and still get the errors =/

    Going to order some new ram. What 2x2GB set do you guys recommend?
    System 1: GA-EP45-UD3R 1.1 / Intel Q9550 (E0) 2.83GHz / XIGMATEK Dark Knight-S1283V / 2x2GB Samsung DDR2-800 / MSI N260GTX-T2D896-OCv2 GeForce GTX 260 896MB / Samsung SyncMaster 2233SW+

    System 2: GA-EP45-UD3P 1.1 / Intel E8500 (E0) 3.16GHz / Corsair PC2-6400 TWIN2X4096-8500C5D (2x2GB DDR2-1066 5-5-5-15-2)

  5. #55
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: GA-EP45-UD3P + 4GB/8GB Corsair Dominator DDR2 1066 Intermittent Problems

    If I were your Plexor and don't know if you tried these settings but here you go.

    Performance Enhance....................: [STANDARD]
    Extreme Memory Profile (X.M.P.)........: [PROFILE 2] <--Disable
    (G)MCH Frequency Latch.................: [333Mhz] <-- Auto
    System Memory Multiplier ..............: [3.20B]
    Memory Frequency (Mhz) ................: 1066

    >>>>> Advanced Timing Control
    > Advanced Timing Control [Press Enter]
    tRRD...................................: 4 [ AUTO] <--4
    tWTR...................................: 4 [ AUTO] <--4
    tWR....................................: 8 [ AUTO] <--6
    tRFC...................................: 68 [ AUTO] <-- 58
    tRTP...................................: 4 [ AUTO] <-- 4
    Command Rate (CMD) ....................: 0 [0] <--2

    Channel A
    Driving Strength ......................: [1066MHz]

    Static tRead Value.....................: 8 [ AUTO] <--8

    Channel B
    Driving Strength ......................: [1066MHz]

    Static tRead Value.....................: 8 [ AUTO] <--8

    > Motherboard Voltage Control
    >>> CPU
    Load-Line Calibration..................: [ENABLED]
    CPU Vcore..............................: 1.18750V [NORMAL] <--1.8750 or what ever default is or maybe up a notch or 2
    CPU Termination........................: 1.200V [NORMAL] <--1.200
    CPU PLL................................: 1.500V [NORMAL] <--1.500
    CPU Reference..........................: 0.760V [AUTO]

    >>> MCH/ICH
    MCH Core...............................: 1.100V [1.260V]
    MCH Reference..........................: 0.760V [AUTO]
    MCH/DRAM Ref...........................: 0.900V [AUTO]
    ICH I/O................................: 1.500V [AUTO]
    ICH Core...............................: 1.100V [AUTO]

    >>> DRAM
    DRAM Voltage...........................: 1.800V [2.100V]
    DRAM Termination.......................: 0.900V [AUTO] << Leave

  6. #56
    Join Date
    Oct 2009
    Posts
    3

    Default Re: GA-EP45-UD3P + 4GB/8GB Corsair Dominator DDR2 1066 Intermittent Problems

    My new set is doing well so far... I have my MCH at 1.24.

    Plexor, I think you need to RMA that ram. That's what my last set was doing.

    I've heard of some people having better luck with using memory slots 2 & 4 instead of 1 & 3, so you may want to try that.

  7. #57
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: GA-EP45-UD3P + 4GB/8GB Corsair Dominator DDR2 1066 Intermittent Problems

    Setting lower values than those that are in the SPD profile are not gong to fix any errors, if anythig will is loosening them. I'd stick to XMP profile1/2 with all timings on auto, and concentrate on DRAM Voltage and MCH Core, in the ranges 1.2-1.26v / 1.05-0.95v, whichever works.

  8. #58
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: GA-EP45-UD3P + 4GB/8GB Corsair Dominator DDR2 1066 Intermittent Problems

    Quote Originally Posted by Chike View Post
    Setting lower values than those that are in the SPD profile are not gong to fix any errors, if anythig will is loosening them. I'd stick to XMP profile1/2 with all timings on auto, and concentrate on DRAM Voltage and MCH Core, in the ranges 1.2-1.26v / 1.05-0.95v, whichever works.
    PHOOEY on XMP profiles Chike..you know better than suggest those...

  9. #59
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: GA-EP45-UD3P + 4GB/8GB Corsair Dominator DDR2 1066 Intermittent Problems

    Quote Originally Posted by Conners View Post
    PHOOEY on XMP profiles Chike..you know better than suggest those...
    I am all for XMP profiles, allways suggest them, they are made for a reason and have been tested. If you want tighter timings than ovveride them, but XMP profiles should be safe.

  10. #60
    Join Date
    Nov 2008
    Location
    Hu3zil
    Posts
    64

    Default Re: GA-EP45-UD3P + 4GB/8GB Corsair Dominator DDR2 1066 Intermittent Problems

    XMP Profiles IS SAFE, i always use them, but since i'm overclocking my dimms to 1133Mhz, leaving on Auto looses my timings, so i override them.

    Test your dimms 2x2GB at time, then test another kit, and you must see your kits are all the same revision or not, if not you'll run into problems. I faced that, mixed rev. 4.1 and 5.1 and caboom! No post!

Page 6 of 7 FirstFirst ... 4567 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •