Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 7 of 7

Thread: Help OC E5200 & EP45UD3R




  1. #1
    Join Date
    May 2009
    Posts
    5

    Default Help OC E5200 & EP45UD3R

    Hi all..
    this my current stable setting
    just trying to run 344/345x10.5/11 for 1150 mem freq
    i'm able to login to windows but got freeze after that
    need some help to get a stable
    core 0 stuck on 41c 'i.ve already reaseted hsf but nothing change..is it okay?

    Thank you in advance for any help

    E5200 RO Stepping vid 1.2750

    EP45-UD3R Rev 1.1 F9

    OCZ Reaper HPC Edition 4GB (2x2048) PC9200
    OCZ Technology | Products | Memory | OCZ DDR2 PC2-9200 Reaper HPC 4GB Edition

    Patriot Viper 2GB (2x1024) PC8500
    Patriot Memory - Products

    Code:
    Robust Graphics Booster ...............: [Fast]
    CPU Clock Ratio .......................: [   12]
    Fine CPU Clock Ratio...................:  +0.0
    CPU Frequency .........................: 4.06Hz
    
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control.................: [Enabled] 
    CPU Host Frequency (Mhz) ..............:  399Mhz
    PCI Express Frequency (Mhz) ...........:  100
    
    C.I.A.2 ...............................: [Disabled]
    
    Advanced Clock Control [Press Enter]
    CPU Clock Drive........................: 800mV
    PCI Express Clock Drive................: 900mV
    CPU Clock Skew (ps)....................:   0ps
    MCH Clock Skew (ps)....................:   0ps
    
    DRAM Performance Control
    Performance Enhance....................: [STANDARD]
    Extreme Memory Profile (X.M.P.)........: [Disabled]
    (G)MCH Frequency Latch.................:  Auto
    System Memory Multiplier ..............:  3.33D 
    Memory Frequency (Mhz) ................:  1130
    DRAM Timing Selectable ................: [Manual]
    
    Standard Timing Control
    CAS Latency Time.......................: 5
    tRCD ..................................: 5
    tRP'...................................: 5
    tRAS...................................: 15
    
    Advanced Timing Control
    tRRD...................................: 3
    tWTR...................................: 3
    tWR....................................: 4
    tRFC...................................: 52
    tRTP...................................: 3
    Command Rate (CMD) ....................: 2
    
    Driving Strength Profiles
    Driving Strength ......................: Auto
    
    Channel A
    Static tRead Value.....................:     6
    tRD Phase0 Adjustment..................: [Auto]
    tRD Phase1 Adjustment..................: [Auto]
    tRD Phase2 Adjustment .................: [Auto]
    tRD Phase3 Adjustment..................: [Auto]
    
    Trd2rd(Different Rank).................: [Auto]
    Twr2wr(Different Rank).................: [Auto]
    Twr2rd(Different Rank).................: [Auto]
    Trd2wr(Same/Diff Rank).................: [Auto]
    
    Dimm1 Clock Skew Control...............: [Auto]
    Dimm2 Clock Skew Control...............: [Auto]
    DDR Write Training.....................: [Auto]
    
    Channel B
    Static tRead Value.....................:     6
    tRD Phase0 Adjustment..................: [Auto]
    tRD Phase1 Adjustment..................: [Auto]
    tRD Phase2 Adjustment .................: [Auto]
    tRD Phase3 Adjustment..................: [Auto]
    
    Trd2rd(Different Rank).................: [Auto]
    Twr2wr(Different Rank).................: [Auto]
    Twr2rd(Different Rank).................: [Auto]
    Trd2wr(Same/Diff Rank).................: [Auto]
    
    Dimm1 Clock Skew Control...............: [Auto]
    Dimm2 Clock Skew Control...............: [Auto]
    DDR Write Training.....................: [Auto]
    
    Motherboard Voltage Control
    Voltage Type...........................: [Manual]
    
    CPU---------------------Normal-----------Current
    
    Load Line Calibration..................: [Disabled]
    CPU Vcore...............1.25000V.......: 1.43750V -> iddle: 1.408 load: 1.392/1.376
    CPU Termination.........1.200V.........: 1.200V
    CPU PLL.................1.500V.........: 1.500V
    CPU Reference...........0.760V.........: [Auto]  
    
    MCH/ICH
    MCH Core................1.100V.........: 1.100V
    MCH Reference...........0.760V.........: 0.760V
    MCH/DRAM Reference......0.900V.........: 0.900V
    ICH I/O.................1.500V.........: 1.500V
    ICH Core................1.100V.........: 1.100V
    
    DRAM
    DRAM Voltage............1.800V.........: 2.060V 
    DRAM Termination........0.900V.........: [Auto]
    Channel A Reference.....0.900V.........: [Auto]
    Channel B Reference.....0.900V.........: [Auto]
    
    Advanced Settings
    Limit CPUID Max. to 3..................: [Disabled]
    No-Execute Memory Protect..............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support...................: [Disabled]
    x C4/C4E State Support.................: [Disabled]
    CPU Thermal Monitor 2(TM2) ............: [Enabled]
    CPU EIST Function......................: [Disabled]
    Virtualization Technology..............: [Disabled]
    
    Integrated Peripherals
    Legacy USB Storage Detect .............: [Disabled]

  2. #2
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Help OC E5200 & EP45UD3R

    So you are using 6GB of mixed ram? If so that is likely the whole issue, you should not mix ram especially from different brands and models/speeds

    I do see several things wrong with your settings though, so you may be ok once you make some changes.

    For one you likely need at least 1.20-1.24V MCH Voltage, maybe more. And I would go ahead and set your ram voltage to 2.1V-2.2V to be sure this is not an issue.

    Then set 1.225-1.35 Vtt (Cpu Termination).

    Also raise your tRFC to 68 for now to be sure this is not an issue, and raise your tRD (Static tRead Value) to 9 for now as well

  3. #3
    Join Date
    May 2009
    Posts
    5

    Default Re: Help OC E5200 & EP45UD3R

    thanks for reply Lsdmeasap
    as your advice, here's the result
    just using 342x12 (1140 mem freq)
    vtt 1.220v
    if mch more than 1.20v it wont post
    if ram voltage more than 2.1v it wont post
    btw how bout my vcore ..is it safe for daily usage?
    thank in advance
    sorry for bad english

  4. #4
    Join Date
    Apr 2009
    Location
    J'Habite En Angleterre
    Posts
    2,431

    Default Re: Help OC E5200 & EP45UD3R

    Nothing really wrong with your Vcore IMO, I'm running slightly higher with no issues (1.45V just over in the BIOS).

    Your Core 0 temperature sensor is just stuck, so your heatsink is seated fine. Both my DTS sensors are stuck at low temps, one at 34c and the other at 39c, but they're fine at load and are I assume relatively accurate.

    You do seem to be running a very high over clock for an E5xxx series. This leads me to believe that either you have been blessed with an amazing chip, or your overclock isn't stable. Have you done any stability testing? I recommend Prime95 for 12 Hours on blend as a minimum. If you want to do a quick check first, download Intel Burn Test. Run 5 itterations at maximum stress, and it'll tell you if your system is relatively stable or not. Note that a pass in IBT doesn't guarantee stability, and prime95 may still fail.

    Watch temperatures carefully. More than 65c loaded in Prime may be cause for concern, and 70c+ means you dfinately need to back off a bit. IBT temps may also go through the roof, as nothing heats up the CPU better than IBT.My 60-63c load temps turn into 72c+ with IBT on a hot day (27c ambient, no air con in the UK).

    By the way, your English is good, nothing to worry about there!
    Coolermaster CM 690 II advance Case
    Corsair HX750 (CWT, 91%(80+ Gold rated @230V) single 62A 12V rail
    P55A-UD4 v2.0 @ F14
    Core i5 760 @ 20 x 201, 4.02GHz
    TRUE Black with a single Noctua NF-P12 pumping out 55 CFM @ 19db .
    2 x 2GB Mushkin Ridgeback (996902), @ 7-10-8-27, 2010-DDR, 1.66v
    2 x Gigabyte GTX 460 1024MB in SLI (Pre OC'd to 715MHz core and 1800MHz VRAM) @ 850 Core / 4100 Mem.
    Intel X25-M Boot Drive (OS and Programs) 200MB/s Read & 90MB/s Write
    Corsair X32 200MB/s Read & 100MB/s Write
    WD Caviar Blue 640GB C (Steam, Games, Storage, Temp Files & Folders, etc)
    Samsung F3 500GB Backup/Images
    Noctua 1300RPM 19dB case fan (rear extraction)
    3 x 140 MM Coolermaster LED fans (one front intake, one top extraction, one side intake)
    Dell Ultra Sharp 2209WAf E-IPS @ 1680x1050

  5. #5
    Join Date
    May 2009
    Posts
    5

    Default Re: Help OC E5200 & EP45UD3R

    thanks for your reply Psycho101
    just run blend orthos for 2 hours (345x11 to reach mem 1150)
    after pass 2 hours, according HWMonitor, max cpu temp is 68c and max core temp is 63c..is it still okay?
    thanks in advance
    http://img5.imageshack.us/img5/8139/40472576.jpg

  6. #6
    Join Date
    Apr 2009
    Location
    J'Habite En Angleterre
    Posts
    2,431

    Default Re: Help OC E5200 & EP45UD3R

    Hmm... From your screenshot there I see you're running 345*11. That's a good overclock. However in your BIOS template you filled out 399 FSB * 12 for 4.06GHz. This adds up to over 4.7GHz. I assume it was a mistake when filling out the template.

    Your temperatures seem good. Any thing under 65c is definitely fine. I'd recommend you run Orthos for at least 8 hours though, 12 would be perfect. I and many others have had Prime/Orthos fail after 3-6 hours, and some at the last couple of hours before the end of a 24 hour run.
    Coolermaster CM 690 II advance Case
    Corsair HX750 (CWT, 91%(80+ Gold rated @230V) single 62A 12V rail
    P55A-UD4 v2.0 @ F14
    Core i5 760 @ 20 x 201, 4.02GHz
    TRUE Black with a single Noctua NF-P12 pumping out 55 CFM @ 19db .
    2 x 2GB Mushkin Ridgeback (996902), @ 7-10-8-27, 2010-DDR, 1.66v
    2 x Gigabyte GTX 460 1024MB in SLI (Pre OC'd to 715MHz core and 1800MHz VRAM) @ 850 Core / 4100 Mem.
    Intel X25-M Boot Drive (OS and Programs) 200MB/s Read & 90MB/s Write
    Corsair X32 200MB/s Read & 100MB/s Write
    WD Caviar Blue 640GB C (Steam, Games, Storage, Temp Files & Folders, etc)
    Samsung F3 500GB Backup/Images
    Noctua 1300RPM 19dB case fan (rear extraction)
    3 x 140 MM Coolermaster LED fans (one front intake, one top extraction, one side intake)
    Dell Ultra Sharp 2209WAf E-IPS @ 1680x1050

  7. #7
    Join Date
    May 2009
    Posts
    5

    Default Re: Help OC E5200 & EP45UD3R

    opps sorry
    it should be 339x12
    tried to run 345x12 but got freeze after 2 min in blend orthos

    5 hours pased..7 hours to go :)

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •