Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: Need help setting up bios




  1. #1
    Join Date
    Jun 2009
    Location
    Harrisburg, PA
    Posts
    38

    Default Need help setting up bios

    I was getting random bsod so I did a clean reinstall of Vista Ultimate. Still no joy. This is my system:

    GA-P45T-DS3R Rev 1.0 - Bios F3
    Intel Core2Quad 9400 2.66 MHz
    Zalman cnps9700
    XFX geforce 9800gt
    2 x 2GB Crucial Ballistix ddr3 1333 (6-6-6-20 listed on sticks )
    Antec True Power Trio 550 W
    WD esata 1T

    I have been reading various posts to try to set up my bios simply for stability at present, not even trying to oc

    I am at the point of getting only one failure in memtest, but for some strange reason, I am trying for no errors.

    Here in brief is my bios

    M I T
    Robust - Auto
    CPU clock ratio - 7.0
    Fine CPU clock - 0
    CPU Frequency - 2.33 GHz ( 7 x 333 )

    Clock Chip Control
    No change from default

    Advanced Clock Control
    CPU Clock Drive 800 mV
    PCI Express 900 mV
    CPU Clock Skew 0ps
    MCH Clock Skew 0ps

    DRAM Performance

    Performance - Standard
    (G)MCH Freq Latch - 333 MHz
    Syst Mem Mult - 4.00B
    Mem Freq - 1333 [1333]
    DRAM Timing - Manual

    Std Timing Control

    CAS Latch - 9 [9]
    tRCD - 9 [9]
    tRP - 9 [9]
    tRAS - 9 [9]

    Adv Timing Control

    tRDD - 4 [Auto]
    tWTR - 5 [Auto]
    tWR - 10 [Auto]
    tRFC - 74 [Auto]
    tRTP - 5 [Auto]
    Cmd - 0 [Auto]

    everything else is at default or I can get specific info if needed.

    So before I even try to oc I need to get this puppy to run stable and close to spec

    Are there any suggestions on what my next step should be?

    Thanks,

    Dan

  2. #2
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: Need help setting up bios

    I would suggest you reset the comos then load optimized defaults. After loading optimized defaults you should save and exit, then enter the BIOS again. Then set your drives to either IDE, ACHI or Raid and any other changes you want to make. Reboot into Vista. One error in memtest is probably nothing to worry about at this point. But thats jut my opin.
    Last edited by Conners; 06-29-2009 at 11:44 AM.

  3. #3
    Join Date
    Jun 2009
    Location
    Harrisburg, PA
    Posts
    38

    Default Re: Need help setting up bios

    Thanks for the suggestion.

    I actually reloaded the fail safe bios. When I did that the DRAM Performance Enhance defaulted to Turbo and when I ran memtest the screen turned red with continuous errors, failing in test 5.

    I then went back into the bios and the only changes I made were to lower the CPU ratio from 8x to 7x, lowered Performance enhance from turbo to standard, kept (G)MCH at 333 MHz with the system memory multiplier at 4.00B, (giving the memory frequency 1333 MHz), DRAM timing to manual and left Cas 9 [Auto], tRCD 9 [Auto], tRP 9 [Auto], tRAS 9 [Auto], and left all the voltages at the defaults from fail safe. Now when I run memtest I get no errors ( with only one pass so far ) BUT with the 7 x multiplier I'm only getting 2.33 GHz from my 2.66 GHz CPU ( Q9400 )

    I would sure like to at least get the "advertised" speed of 2.66 GHZ.

    Any ideas on what I should do next??

    D
    GA-P45T-DS3R Rev 1.0 - Bios F3
    Intel Core2Quad 9400 2.66 MHz
    Zalman cnps9700
    XFX geforce 9800gt 512
    2 x 2GB Crucial Ballistix ddr3 1333 http://www.crucial.com/store/partspe...KIT25664BA1336
    Antec True Power Trio 550 W
    WD esata 1T
    Seagate Pro External USB 600 GB

  4. #4
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: Need help setting up bios

    Can you post your current bios settings? There is a template somewhere on here just search for your motherboard specs and template...

  5. #5
    Join Date
    Jun 2009
    Location
    Harrisburg, PA
    Posts
    38

    Default Re: Need help setting up bios

    I couldn't find the template, so I took pictures I'll attach the first then try to upload the next later
    GA-P45T-DS3R Rev 1.0 - Bios F3
    Intel Core2Quad 9400 2.66 MHz
    Zalman cnps9700
    XFX geforce 9800gt 512
    2 x 2GB Crucial Ballistix ddr3 1333 http://www.crucial.com/store/partspe...KIT25664BA1336
    Antec True Power Trio 550 W
    WD esata 1T
    Seagate Pro External USB 600 GB

  6. #6
    Join Date
    Jun 2009
    Location
    Harrisburg, PA
    Posts
    38

    Default Re: Need help setting up bios

    Here are the next set
    GA-P45T-DS3R Rev 1.0 - Bios F3
    Intel Core2Quad 9400 2.66 MHz
    Zalman cnps9700
    XFX geforce 9800gt 512
    2 x 2GB Crucial Ballistix ddr3 1333 http://www.crucial.com/store/partspe...KIT25664BA1336
    Antec True Power Trio 550 W
    WD esata 1T
    Seagate Pro External USB 600 GB

  7. #7
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: Need help setting up bios

    I don't know much about the Q9400 stock settings so please fill out this template with optimized defaults loaded. Also If your running sata drives and want to run them in AHCI you would have had to select AHCI in the bios when installing the OS. Not that running in IDE mode is bad.

    Also include more detailed information on your memory such as stock timings and voltage.

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto or Fast  <-- Fast
    CPU Clock Ratio ..........................: 8
    Fine CPU Clock Ratio.....................:  0
    CPU Frequency ...........................: 2.66 MHz
     
     
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled] 
    CPU Host Frequency (Mhz) ............: 333 Mhz
    PCI Express Frequency (Mhz) .........:Set to 100
     
    C.I.A.2 .................................:[Disabled]
     
     
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 
    MCH Clock Skew (ps)...................: <<< 
     
     
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 
    Memory Frequency (Mhz) ..............: 
    DRAM Timing Selectable ................: [Manual]
     
    Standard Timing Control
    CAS Latency Time........................
    tRCD .........................................
    tRP'...........................................
    tRAS..........................................
     
    Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
     
    Advanced Timing Control
    tRRD...........................................
    tWTR..........................................
    tWR............................................
    tRFC...........................................
    tRTP...........................................
    Command Rate (CMD) ....................:2
     
    Driving Strength Profiles
    Driving Strength ............................
     
    Channel A
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
     
    Channel B
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
     
    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages
     
    CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore.  Auto is fine if not overclocking
     
    CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.5-1.65.  Auto is fine if not overclocking
     
    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 
     
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 
     
    MCH/ICH
    MCH Core…………….....1.100V...........: << 
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.500V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave
     
    DRAM
    DRAM Voltage ……....1.800V............: 
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave
     
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
     
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
    Last edited by Conners; 07-01-2009 at 02:40 AM.

  8. #8
    Join Date
    Jun 2009
    Location
    Harrisburg, PA
    Posts
    38

    Default Re: Need help setting up bios

    I will show the differences in my Optimized Settings in Red

    The Crucial Ballistix DDR3 are a 4 GB Kit each 2 GB DDR3 PC3-10600 CL6, 1.8V and each is marked 6-6-6-20 1.8V

    The only cmos settings so far that is stable is the one I show in the photos I took of the cmos. That is, I've been running two days ( LOL ) without a bsod


    Quote Originally Posted by Conners View Post
    I don't know much about the Q9400 stock settings so please fill out this template with optimized defaults loaded. Also If your running sata drives and want to run them in AHCI you woulds have had to select AHCI when installing the OS. Not that running in IDE mode is bad.

    Also include more detailed information on your memory such as stock timings and voltage.

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 8
    Fine CPU Clock Ratio.....................:  0
    CPU Frequency ...........................: 2.66 MHz
     
     
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: Disabled
    CPU Host Frequency (Mhz) ............: 333 Mhz
    PCI Express Frequency (Mhz) .........:Auto
     
    C.I.A.2 .................................:[Disabled]
     
     
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: 0 ps
    MCH Clock Skew (ps)...................: 0 ps
     
     
    DRAM Performance Control
    Performance Enhance...................: Turbo
    Extreme Memory Profile (X.M.P.).....: Not Applicable
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: SPD Auto
    Memory Frequency (Mhz) ..............: 1333  1333
    DRAM Timing Selectable ................:SPD  Auto
    
    Standard Timing Control
    CAS Latency Time........................ 9 Auto
    tRCD ......................................... 9 Auto
    tRP'........................................... 9 Auto
    tRAS.......................................... 24 Auto
     
    Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
     
    Advanced Timing Control
    tRRD........................................... 4 Auto
    tWTR.......................................... 5 Auto
    tWR............................................ 10 Auto
    tRFC........................................... 74 Auto
    tRTP........................................... 5 Auto
    Command Rate (CMD) ....................: 0
     
    Driving Strength Profiles
    Driving Strength ............................ Not Applicable 
      Channel A and Channel b are "grayed out" 
    Channel A
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
     
    Channel B
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
     
    Motherboard Voltage Control
    Voltage Type.………... Normal
    CPU
    CPU Vcore….……….........................: 1.21250 Auto
     
    CPU Termination…..... 1.200V*.......: 1.2000 Auto
     
    CPU PLL…………………....1.500V*.......: 1.5000 Auto
     
    CPU Referen.…………....0.755V*.......: 0.760 Auto
     
    CPU Reference2………,,0.800V*.......:Not Applicable
     
    MCH/ICH
    MCH Core…………….....1.100V...........: 1.100 Auto
    MCH Reference….…….0.800V...........; 0.760 Auto
    MCH/DRAM Ref.…......0.900V...........: 0.750 Auto
    ICH I/O……………….....1.500V............: 1.500 Auto
    ICH Core…………...……1.100V............: Not Applicable
     
    DRAM
    DRAM Voltage ……....1.800V............: 1.500 Auto
    DRAM Termination .…0.900V............: 0.750 Auto
    Channel A Reference 0.900V............: 0.750 Auto
    Channel B Reference 0.900V............: 0.750 Auto
     
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: Enabled
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: Enabled
    Virtualization Technology................:  Enabled if you use Vmware/Virtual PC
     
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
    GA-P45T-DS3R Rev 1.0 - Bios F3
    Intel Core2Quad 9400 2.66 MHz
    Zalman cnps9700
    XFX geforce 9800gt 512
    2 x 2GB Crucial Ballistix ddr3 1333 http://www.crucial.com/store/partspe...KIT25664BA1336
    Antec True Power Trio 550 W
    WD esata 1T
    Seagate Pro External USB 600 GB

  9. #9
    Join Date
    Apr 2009
    Location
    J'Habite En Angleterre
    Posts
    2,431

    Default Re: Need help setting up bios

    From my brief viewing of your template I see there are alot of settings on auto. Also, note that your RAM needs 1.8V to be able to perform at 1333 with 6-6-6-20, you have it on auto which will default to 1.5V. Below I've included an amended template for you to try. Don't worry just yet if it fails, it can be tweaked.

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 8
    Fine CPU Clock Ratio.....................:  0
    CPU Frequency ...........................: 2.66 MHz
     
     
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: Disabled
    CPU Host Frequency (Mhz) ............: 333 Mhz
    PCI Express Frequency (Mhz) .........:100
     
    C.I.A.2 .................................:[Disabled]
     
     
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: 0 ps
    MCH Clock Skew (ps)...................: 0 ps
     
     
    DRAM Performance Control
    Performance Enhance...................: STANDARD!
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: Try all the 4.00 multipliers. 4.00B first, then 4.00D
    Memory Frequency (Mhz) ..............: 1333  1333
    DRAM Timing Selectable ................:  MANUAL!
    
    Standard Timing Control
    CAS Latency Time........................ 9 <--6
    tRCD ......................................... 9 <--6
    tRP'........................................... 9 <--6
    tRAS.......................................... 24 <--20
     
    Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
     
    Advanced Timing Control
    tRRD........................................... 4 <-5
    tWTR.......................................... 5 <-5
    tWR............................................ 10 <-11
    tRFC........................................... 74 <-74
    tRTP........................................... 5 <-6
    Command Rate (CMD) ....................: 2
     
    Driving Strength Profiles
    Driving Strength ............................ 1333, or try auto. greyed out because you had RAM SPD on auto. 
     
    Channel A
    Static tRead Value.........................:8
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
     
    Channel B
    Static tRead Value.........................:8
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
     
    Motherboard Voltage Control
    Voltage Type.………... Normal
    CPU
    CPU Vcore….……….........................: 1.21250 Auto
     
    CPU Termination…..... 1.200V*.......: 1.2000 
     
    CPU PLL…………………....1.500V*.......: 1.5000 
     
    CPU Referen.…………....0.755V*.......: 0.760 Auto
     
    
    MCH/ICH
    MCH Core…………….....1.100V...........: 1.240V
    MCH Reference….…….0.800V...........; 0.760 Auto
    MCH/DRAM Ref.…......0.900V...........: 0.750 Auto
    ICH I/O……………….....1.500V............: 1.500 Auto
    ICH Core…………...……1.100V............: Not Applicable
     
    DRAM
    DRAM Voltage ……....1.500V............: 1.800V <-- set to manufacturer spec, yours is 1.8V
    DRAM Termination .…0.900V............:  Auto
    Channel A Reference 0.900V............:  Auto
    Channel B Reference 0.900V............:  Auto
     
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled] C1 is fine to use, C2/C2E abd C4/C4E below may cause issues. Leave those disabled.
    C2/C2E State Support....................: Disabled
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: Enabled
    Virtualization Technology................:  Enabled if you use Vmware/Virtual PC
     
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
    I've used your RAM's VDIMM requirement. Also note MCH core is increased. 1.10V MCH is seldom enough. Your Vcore is fine on auto if not over clocking, but setting CPU term and PLL to manual defaults is good practice.

    Also note they you need to set RAM timings yourself. The primary timings are to your RAM's specs, but I've suggested looser sub-timings and a tRead of 8 for now as I guarantee they're a stable selection.
    Coolermaster CM 690 II advance Case
    Corsair HX750 (CWT, 91%(80+ Gold rated @230V) single 62A 12V rail
    P55A-UD4 v2.0 @ F14
    Core i5 760 @ 20 x 201, 4.02GHz
    TRUE Black with a single Noctua NF-P12 pumping out 55 CFM @ 19db .
    2 x 2GB Mushkin Ridgeback (996902), @ 7-10-8-27, 2010-DDR, 1.66v
    2 x Gigabyte GTX 460 1024MB in SLI (Pre OC'd to 715MHz core and 1800MHz VRAM) @ 850 Core / 4100 Mem.
    Intel X25-M Boot Drive (OS and Programs) 200MB/s Read & 90MB/s Write
    Corsair X32 200MB/s Read & 100MB/s Write
    WD Caviar Blue 640GB C (Steam, Games, Storage, Temp Files & Folders, etc)
    Samsung F3 500GB Backup/Images
    Noctua 1300RPM 19dB case fan (rear extraction)
    3 x 140 MM Coolermaster LED fans (one front intake, one top extraction, one side intake)
    Dell Ultra Sharp 2209WAf E-IPS @ 1680x1050

  10. #10
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: Need help setting up bios

    Mine is pretty much like psycho101 suggestions. One thing I did notice is that your ram (if I guessed right on the model) is not supported by your motherboard. In fact it doesn't list any Crucial ram. Does that matter? Not sure.

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto <-- Fast
    CPU Clock Ratio ..........................: 8
    Fine CPU Clock Ratio.....................:  0
    CPU Frequency ...........................: 2.66 MHz
     
     
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: Disabled
    CPU Host Frequency (Mhz) ............: 333 Mhz
    PCI Express Frequency (Mhz) .........:Auto <-- 100
     
    C.I.A.2 .................................:[Disabled]
     
     
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: 0 ps
    MCH Clock Skew (ps)...................: 0 ps
     
     
    DRAM Performance Control
    Performance Enhance...................: Turbo  << - Standard
    Extreme Memory Profile (X.M.P.).....: Not Applicable
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: SPD Auto  <-- Auto
    Memory Frequency (Mhz) ..............: 1333  1333
    DRAM Timing Selectable ................:SPD  Auto  <-- Manual 
    
    Standard Timing Control
    CAS Latency Time........................ 9 Auto <-- 6
    tRCD ......................................... 9 Auto  <-- 6
    tRP'........................................... 9 Auto <-- 6
    tRAS.......................................... 24 Auto <-- 20
     
    Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
     
    Advanced Timing Control
    tRRD........................................... 4 Auto <-- 4
    tWTR.......................................... 5 Auto  <-- 5
    tWR............................................ 10 Auto <-- 10
    tRFC........................................... 74 Auto <-- 74
    tRTP........................................... 5 Auto <-- 5
    Command Rate (CMD) ....................: 0 <-- 2
     
    Driving Strength Profiles
    Driving Strength ............................ Not Applicable  <--1333
      Channel A and Channel b are "grayed out" 
    Channel A
    Static tRead Value.........................: <--9
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
     
    Channel B
    Static tRead Value.........................: <-- 9
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
     
    Motherboard Voltage Control
    Voltage Type.………... Normal
    CPU
    CPU Vcore….……….........................: 1.21250 Auto 
     
    CPU Termination…..... 1.200V*.......: 1.2000 Auto
     
    CPU PLL…………………....1.500V*.......: 1.5000 Auto
     
    CPU Referen.…………....0.755V*.......: 0.760 Auto
     
    CPU Reference2………,,0.800V*.......:Not Applicable
     
    MCH/ICH
    MCH Core…………….....1.100V...........: 1.100 Auto
    MCH Reference….…….0.800V...........; 0.760 Auto
    MCH/DRAM Ref.…......0.900V...........: 0.750 Auto
    ICH I/O……………….....1.500V............: 1.500 Auto
    ICH Core…………...……1.100V............: Not Applicable
     
    DRAM
    DRAM Voltage ……....1.800V............: 1.500 Auto <-- 1.800V
    DRAM Termination .…0.900V............: 0.750 Auto
    Channel A Reference 0.900V............: 0.750 Auto
    Channel B Reference 0.900V............: 0.750 Auto
     
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: Enabled <-- Disable
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: Enabled <-- if overclocking disable
    Virtualization Technology................:  Enabled if you use Vmware/Virtual PC
     
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
    good luck and let us know if this helps

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •