Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 1 of 5 123 ... LastLast
Results 1 to 10 of 44

Thread: ep45-ud3p rev 1.6 Still Not on gigabyte website !!!




  1. #1
    Join Date
    Jun 2009
    Posts
    17

    Default ep45-ud3p rev 1.6 Still Not on gigabyte website !!!

    ep45-ud3p rev 1.6

    Ive had this board for 3 weeks now and this revision is still not on thier website. I am waiting for a new/better bios..
    I can boot 560fsb but anything over 500 isnt stable..a new bios might help.

    come on gigabyte ...waiting.

  2. #2
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: ep45-ud3p rev 1.6 Still Not on gigabyte website !!!

    I will ask about this now, and see if there is any new BIOS they have for you.

  3. #3
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: ep45-ud3p rev 1.6 Still Not on gigabyte website !!!

    Where are you from? I see you are using a Texas IP Address, so are you from the US or just using an American IP address? Where did you purchase the board?

    I ask because the pages are only updated in the region that board is sold in, so apparently it should not be in the US since neither of the US sites have updated.

  4. #4
    Join Date
    Jun 2009
    Posts
    17

    Default Re: ep45-ud3p rev 1.6 Still Not on gigabyte website !!!

    live in ca, antioch
    got it at frys in concord ,ca

    thanks

  5. #5

    Default Re: ep45-ud3p rev 1.6 Still Not on gigabyte website !!!

    I can boot 560fsb but anything over 500 isnt stable..a new bios might help.
    Are you sure you have the MCH reference tweaked correctly for 500+ fsb?


    Core2Duo E8500 E0 @4.25GHz (500x8.5)
    | Windows 7 RC Build 7100 | Visiontek HD4850 OC 685/1100
    Gigabyte
    GA-EP45T-DS3R | 4Gb (2x2Gb) 1333MHz Patriot DDR3 | 1.14TB (640+500gb) WDC Green
    Antec Earthwatts 500w |
    Antec Nine Hundred
    Screenshots:
    [1][2][3][4][5][6]

  6. #6
    Join Date
    Apr 2009
    Location
    J'Habite En Angleterre
    Posts
    2,431

    Default Re: ep45-ud3p rev 1.6 Still Not on gigabyte website !!!

    Seconded ^^ .

    Read the guide in Lsdmeasap's signature. In simple terms, setting CPU termination temporarily to 1.2V, then reducing MCH ref to 0.740, 0.720, 0.70 and in some cases 0.680 and lower, then increasing CPU termination back up can have huge effects on stability. For example, prime95 bombs out instantly when started. Setting 0.740V MCH ref at 1.2VTT gave me 4 hours stable, and going to 0.720V gave full 24 hour in blend and 12 hour Large FFT.
    Coolermaster CM 690 II advance Case
    Corsair HX750 (CWT, 91%(80+ Gold rated @230V) single 62A 12V rail
    P55A-UD4 v2.0 @ F14
    Core i5 760 @ 20 x 201, 4.02GHz
    TRUE Black with a single Noctua NF-P12 pumping out 55 CFM @ 19db .
    2 x 2GB Mushkin Ridgeback (996902), @ 7-10-8-27, 2010-DDR, 1.66v
    2 x Gigabyte GTX 460 1024MB in SLI (Pre OC'd to 715MHz core and 1800MHz VRAM) @ 850 Core / 4100 Mem.
    Intel X25-M Boot Drive (OS and Programs) 200MB/s Read & 90MB/s Write
    Corsair X32 200MB/s Read & 100MB/s Write
    WD Caviar Blue 640GB C (Steam, Games, Storage, Temp Files & Folders, etc)
    Samsung F3 500GB Backup/Images
    Noctua 1300RPM 19dB case fan (rear extraction)
    3 x 140 MM Coolermaster LED fans (one front intake, one top extraction, one side intake)
    Dell Ultra Sharp 2209WAf E-IPS @ 1680x1050

  7. #7
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: ep45-ud3p rev 1.6 Still Not on gigabyte website !!!

    Hmm I am not so sure that board should have been sold in the US, I have seen this issue with Fry's/Outpost before.

    I will ask my contact about this for you, and see if he can tell me where they are supposed to be sold so I can get you a link to the correct page

  8. #8
    Join Date
    Jun 2009
    Posts
    17

    Default Re: ep45-ud3p rev 1.6 Still Not on gigabyte website !!!

    am testing may diff configurations anf settings of term and reff 's . Am getting tired of trying. hell 475 and 500 fsb was easy..over 500 ...dam so tired of trying.

  9. #9
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: ep45-ud3p rev 1.6 Still Not on gigabyte website !!!

    Please post for me your full specs and settings and I will see if I can help you get things going smoother. I am sending in a email now to ask again for you about a BIOS or Gigabyte webpage for this model because I can't find one either

    This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

    CPU = Model #
    Motherboard = Model, Revision #
    BIOS Version =
    Ram = Brand, Model#, Part#, And or Link

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto or Fast
    CPU Clock Ratio ..........................: 
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 
    
    
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled] 
    CPU Host Frequency (Mhz) ............: Mhz
    PCI Express Frequency (Mhz) .........:Set to 100
    
    C.I.A.2 .................................:[Disabled]
    
    
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 
    MCH Clock Skew (ps)...................: <<< 
    
    
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 
    Memory Frequency (Mhz) ..............: 
    DRAM Timing Selectable ................: [Manual]
    
    Standard Timing Control
    CAS Latency Time........................
    tRCD .........................................
    tRP'...........................................
    tRAS..........................................
    
    Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
    
    Advanced Timing Control
    tRRD...........................................
    tWTR..........................................
    tWR............................................
    tRFC...........................................
    tRTP...........................................
    Command Rate (CMD) ....................:2
    
    Driving Strength Profiles
    Driving Strength ............................
    
    Channel A
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Channel B
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Motherboard Voltage Control
    
    CPU
    CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages
    
    CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore.  Auto is fine if not overclocking
    
    CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.5-1.65.  Auto is fine if not overclocking
    
    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 
    
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 
    
    MCH/ICH
    MCH Core…………….....1.100V...........: << 
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.500V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave
    
    DRAM
    DRAM Voltage ……....1.800V............: 
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave
    
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

  10. #10
    Join Date
    Jun 2009
    Posts
    17

    Default Re: ep45-ud3p rev 1.6 Still Not on gigabyte website !!!

    um i think i just found somthn.. i set cpu ref. .80
    and mch ref to .70
    vtt 1.26
    mch core 1.4 might try to lower later.
    mem 1:1/ 1070 perf level 9 1.86v need to lower...
    535 fsb x7.5 i think. anyways 4.28ghz 1.4v [1.36/1.38 ]
    loadline enable
    i think i didnt have cpu ref / mch ref set correctly together. one was always off i guess.
    hit 2 hours prime large fft. and rebooted set bios reflecting easytune settings.. primming again. Ive never made it past 1 hour.. i think i am on to somthn..

Page 1 of 5 123 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •