Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 1 of 3 123 LastLast
Results 1 to 10 of 21

Thread: Normal Settings for EP45-UD3P & E8400




  1. #1
    Join Date
    Aug 2009
    Posts
    17

    Default Normal Settings for EP45-UD3P & E8400

    hi all and thanks in advance for any help

    i've searched a bit and have found countless information for overclocking this configuration, but what i am looking for is how to set the bios so my hardware (ram & CPU) just run to spec... when i look at my cpu in cpuid, it shows the core speed jump from 1999.6 to 2666.4 and the multiplier goes from x 6.0 to x8.0. the bus speed stays @ 333.3 MHz and rated FSB @ 1333.2. ont he memory tab in cpuid DRAM Freq shows 400 MHz FSB DRAM shows 5:6. what i am looking for is for my memory to run @ the rated 1066 PC2-6400 5-6-6-18 and the cpu to run @ 3.00 GHz

    Here is snapshot of CPUID:

    cpu-


    Mainboard-


    Memory-


    SPD-


    My Bios looks (as far as i can tell) identical to these for the GA-P45 BIOS Example
    http://forums.tweaktown.com/f69/memo...vs-bios-27283/

    thanks again for the help

  2. #2
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Normal Settings for EP45-UD3P & E8400

    Follow all of the suggestions in this post to get a stable stock setup.
    Follow steps 1 to 4 for additional help.
    Then set:
    CPU Clock Ratio ---------------------- : [9]
    Fine CPU Clock Ratio ----------------- : [0.0] < ignore if not available
    CPU Frequency ---------------------: ####

    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control --------------- : [Enabled]
    CPU Host Frequency (Mhz) ------------: [333]

    Static tRead Value --------------------: [6] for channels A & B

    Your fluctuating cpu multiplier and cpu speed are due to having the following enabled:

    CPU Enhanced Halt (C1E) -------------- : [Disabled]
    CPU EIST Function -------------------- : [Disabled]

    Setting both of these to Disabled will give you full rated speed at all times, at the minor expense of higher power consumption at lower system loads.

    Your memory performance at 800MHz with tight memory timings will be virtually the same as running at 1066MHz with looser timings.
    You can reach 1066 memory speeds (at 3.0GHz) by using:
    Cpu Host Frequency = 400MHz
    Cpu multiplier = 7.5
    System Memory Multiplier = 2.66D
    And you will need to run looser timings for Static tRead Value and Standard Timing Control.

    Even at stock settings, you should still perform extended stability testing using:
    Prime95, OCCT, or Orthos; 3 separate tests using small FFTs, large FFTs, and Blend tests. Each test should be run for 8 to 24 hours.
    Note: Most errors will occur within a 6 hour time frame. An error in any of these tests indicates that your system is not stable.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  3. #3
    Join Date
    Aug 2009
    Posts
    17

    Default Re: Normal Settings for EP45-UD3P & E8400

    thanks for your reply!

    i think ihad figured out some of the settings myself, was running 7.5 x 400 and got the memory to read @ 1066, however i noticed my cpu idle temop had gone up a few degrees, normally about 35-36c and after it was 39-40c, i tried your recomendation and have the cpu running @ 333 x 9 and the memory tighter @ 800MHz, my temp is back to the normal range, i alos found the second "helper" that was varying my cpu readings, it wasn't in the mib tweaker so i had missed it, went looking and found the bugger, now its off, a question i have is, is it easier on the cpu to increase the multiplier rather than the fsb if you can.. going with 333x9 rather than 7.5x400?

  4. #4
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Normal Settings for EP45-UD3P & E8400

    Glad to hear that you're making progress.

    There are some minor performance advantages to running at 333MHz instead of 400MHz if you don't want your system speed higher than 3.0GHz. You shouldn't have a 3 degree (C) increase in temperatures at 400MHz when your bios is properly set up. What is the ambient room temperature in the room?
    Keep in mind that you can probably run your memory at 1066 speeds using 9x333MHz and the 3.20B System Memory Multiplier. You can also run your memory at 800MHz using 400x7.5 and the 2.00B memory multiplier. Some of the bios settings will need to be changed at different cpu FSB speeds and running your memory at 1066 vs 800MHz.

    It will be MUCH easier for us to help you get an optimal setup if you'll post your hardware setup in your forum signature, including the following info:
    mobo model and version number
    bios version number
    cpu model and revision number
    memory brand/model number, size (e.g. 2x2GB) and a link to the memory's specs
    heatsink model (stock? aftermarket?)
    power supply unit brand/model
    etc.

    Providing your bios settings from the generic bios template (available in the post #2 link) will make it quicker and easier for us to provide additional suggestions to optimize your system, prevent possible errors, and it will help other forum members in the future.
    Providing the requested screen-shots from the link in post #2 will help us more quickly determine if some bios settings are not correct.

    Keep in mind that running at 3.60GHz is easily done with your hardware and won't require high voltage settings, either now or in the future.

    I don't want to sound overly harsh, but if you won't provide the requested information, many forum members won't waste their time trying to guess at what any problems or issues might be. Many of us are helping several members at the same time.

    There's a method to our madness, please co-operate with these simple requests. If you have any questions as to how to provide this information, just ask.
    Last edited by profJim; 08-08-2009 at 06:17 PM.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  5. #5
    Join Date
    Aug 2009
    Posts
    17

    Default Re: Normal Settings for EP45-UD3P & E8400

    thanks again for your input, and i'll be happy to get the info posted. definitely appreciate the help. for the ram settings/timmings, do you just need the man info, or an actual link to that info from the website?

  6. #6
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Normal Settings for EP45-UD3P & E8400

    Take a look at GA-EP45-UD3P - Won't boot with 450FSB for an example of how info is posted and shared in a productive way. You don't need to read all 13 pages of posts, but there's a lot of good info there.

    Often times others will post in the same thread with similar setups and related questions. This is why it's best to include your hardware setup in your forum signature. An external link to your memory's specs makes it quick an easy for us to double check info that relates to tweaking and overclocking. Sometimes posters will include links to external websites where related photos can be easily viewed.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  7. #7
    Join Date
    Aug 2009
    Posts
    17

    Default Re: Normal Settings for EP45-UD3P & E8400

    OK- here is the baseline info, i set bios to optimized defaults and made the changes in my bios to reflect changing "auto" to the actual number

    The links to my components should now be in my sig.
    Here is the bios template:
    Code:
    Gigabyte GA-EP45-UD3P (Rev. 1.6) - F8
    *************************************
    MB Intelligent Tweaker(M.I.T.) 
    ******************************
    Robust Graphics Booster ..............: [Fast]
    CPU Clock Ratio ......................: [9X]
    x Fine CPU Clock Ratio................: +0.0
    CPU Frequency ........................: 3.00GHz( 333x9)
    ********** Clock Chip Control ********
    >>>>>  Standard Clock Control
    CPU Host Clock Control................: [Enabled]
    x CPU Host Frequency(Mhz).............: [333]
    PCI Express Frequency(Mhz)............: [100]
    C.I.A.2...............................: [Disabled]
    >>>>> Advanced Clock Control..........: [Press Enter] 
    CPU Clock Drive.......................: [800mV]
    PCI Express Clock Drive...............: [900mV]
    CPU Clock Skew........................: [  0ps]
    MCH Clock Skew........................: [  0ps]
    ******** DRAM Performance Control ********
    Performance Enhance...................: [Standard]
    Extreme Memory Profile(X.M.P.)........: [Disabled]
    (G)MCH Frequency Latch................: [Auto]
    System Memory Multiplier (SPD)........: [Auto]
    Memory Frequency(Mhz).....800.........: [Auto]
    DRAM Timing Selectable (SPD)..........: [Auto]
    >>>>> Standard Timing Control
    x CAS Latency Time................5...: [ 5]
    x tRCD ...........................6...: [5]
    x tRP.............................6...: [5]
    x tRAS...........................18...: [18]
    >>>>> Advanced Timing Control.........: [Press Enter] 
    x tRRD............................3...: [Auto]
    x tWTR............................3...: [Auto]
    x tWR.............................6...: [Auto]
    x tRFC...........................54...: [Auto]
    x tRTP............................3...: [Auto]
    x Command Rate (CMD) .............0...: [0]
    >>>>> Channel A Timing Settings.......: [Press Enter] 
    x Static tRead Value.............10...: [Auto]
    x tRD Phase0 Adjustment...........0...: Auto
    x tRD Phase1 Adjustment...........0...: Auto
    x tRD Phase2 Adjustment ..........0...: Auto
    x tRD Phase3 Adjustment...........0...: Auto
    x Trd2rd(Different Rank)..........6...: Auto
    x Twr2wr(Different Rank)..........6...: Auto
    x Twr2rd(Different Rank)..........5...: Auto
    x Trd2wr(Same/Diff Rank)..........8...: Auto
    x DIMM1 Clock Skew Control (ps).......: Auto
    x DIMM2 Clock Skew Control (ps).......: Auto
    x DDR Write Training..................: Auto
    >>>>> Channel A Driving Settings......: [Press Enter] 
    x Driving Strength Profile............: []
    x Data Driving Pull-Up Level..........: Auto
    x Cmd Driving Pull-Up level...........: Auto
    x Ctrl Driving Pull-Up Level..........: Auto
    x Clk Driving Pull-Up Level...........: Auto
    x Data Driving Pull-Down Level........: Auto
    x Cmd Driving Pull-Down level.........: Auto
    x Ctrl Driving Pull-Down Level........: Auto
    x Clk Driving Pull-Down Level.........: Auto
    >>>>> Channel B Timing Settings.......: [Press Enter] 
    x Static tRead Value.............10...: [Auto]
    x tRD Phase0 Adjustment...........0...: Auto
    x tRD Phase1 Adjustment...........0...: Auto
    x tRD Phase2 Adjustment ..........0...: Auto
    x tRD Phase3 Adjustment...........0...: Auto
    x Trd2rd(Different Rank)..........6...: Auto
    x Twr2wr(Different Rank)..........6...: Auto
    x Twr2rd(Different Rank)..........5...: Auto
    x Trd2wr(Same/Diff Rank)..........8...: Auto
    x DIMM1 Clock Skew Control (ps).......: Auto
    x DIMM2 Clock Skew Control (ps).......: Auto
    x DDR Write Training..................: Auto
    >>>>> Channel B Driving Settings......: [Press Enter] 
    x Driving Strength Profile............: []
    x Data Driving Pull-Up Level..........: Auto
    x Cmd Driving Pull-Up level...........: Auto
    x Ctrl Driving Pull-Up Level..........: Auto
    x Clk Driving Pull-Up Level...........: Auto
    x Data Driving Pull-Down Level........: Auto
    x Cmd Driving Pull-Down level.........: Auto
    x Ctrl Driving Pull-Down Level........: Auto
    x Clk Driving Pull-Down Level.........: Auto
    ****** Motherboard Voltage Control ******
    Voltage Types..........Normal...........Current
    -----------------------------------------------
    >>> CPU
    Load-Line Calibration.................: [Enabled]
    CPU Vcore..............1.30000V.......: [1.30000V]
    CPU Termination........1.200V.........: [1.200V]
    CPU PLL................1.500V.........: [1.500V]
    CPU Reference..........0.760V.........: [Auto]
    >>> MCH/ICH
    MCH Core...............1.100V.........: [1.200V]
    MCH Reference..........0.760V.........: [Auto]
    MCH/DRAM Reference.....0.900V.........: [Auto]
    ICH I/O................1.500V.........: [1.500V]
    ICH Core...............1.100V.........: [1.100V]
    >>> DRAM
    DRAM Voltage...........1.800V.........: [1.800V]
    DRAM Termination.......0.900V.........: [Auto]
    Channel A Reference....0.900V.........: [Auto]
    Channel B Reference....0.900V.........: [Auto]
    ******** Advanced BIOS Features ********
    Hard Disk Boot Priority...............: [Press Enter]
    First Boot Device.....................: [USB-HDD]
    Second Boot Device....................: [Hard Disk]
    Third Boot Device.....................: [CDROM]
    Password Check........................: [Setup]
    HDD S.M.A.R.T. Capability.............: [Enabled]
    Limit CPUID Max. to 3.................: [Disabled]
    No-Execute Memory Protect.............: [Enabled]
    CPU Enhanced Halt (C1E)...............: [Disabled]
    C2/C2E State Support..................: [Disabled]
    x C4/C4E State Support................: Disabled
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.....................: [Disabled]
    Virtualization Technology.............: [Disabled]
    Delay For HDD (Secs)..................: [ 0]
    Full Screen LOGO Show.................: [Disabled]
    Init Display First....................: [PEG]
    ******** Integrated Peripherals ********
    USB Keyboard Function.................: [Enabled]
    USB Mouse Function....................: [Enabled]
    USB Storage Function..................: [Disabled]
    Screenshot w/ requested info


    sorry for the double posting and seeming like this was difficult... many thanks for the tip about the "# (code) to get the template info in...
    Last edited by ColdSteele; 08-09-2009 at 12:26 PM. Reason: Additional text
    My Rig:
    CPU: Intel E8400 Wolfdale
    Mobo: Gigabyte EP45-UD3P Rev. A3
    Bios: F8
    Power: OCZ 600 Stealth ExtremeRAM: OCZ DDR2 PC-8500 2x2Gig
    Gfx: Xfx 9800 GTX+
    Heatsink:
    Tuniq Tower 120

  8. #8
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: Normal Settings for EP45-UD3P & E8400

    To have your ram at 1066 you need to manually set System Memory Multiplier 3.20B and DRAM Voltage to 2.1v, check the BIOS HWMonitor after reboot to see what voltage actually applied to the ram, if it is over/under volted adjust DRAM voltage so HWMonitor show the closest value to 2.1v possible.
    Start with spec timings 5-6-6-18, after you make sure the system is stable you may try and lower them as well as Static tRead Valur (performance Level in MemSet)
    You already set MCH Core to 1.2v so it may be sufficient. If not you may try to raise it a bit to 1.24-1.26v.

  9. #9
    Join Date
    Aug 2009
    Posts
    17

    Default Re: Normal Settings for EP45-UD3P & E8400

    yeah, some of the info i got from the ocz forums reflected that the memory on a clean cmos or first boot, the ram would run @ pc-6400 speeds @1.800v, so i will prolly have to change the dram voltage to 2.1 to get what i'm looking for. i did notice that when i look thru the voltage settings right @2.1 (or maybe 2.0 the number goes "pink", i assume to imply possible dammage? but since that setting is where the ram is spec'd to run it's prolly ok...right?

    one other question concerning voltage... in one the the stickies, it reccomends to up the voltage in several places by 0.1 to increase stability...

    Voltage Types..........Normal...........Current
    -----------------------------------------------
    >>> CPU
    Load-Line Calibration.................: [Enabled]
    CPU Vcore..............1.30000V.......: [1.30000V] <-- change to 1.4?
    CPU Termination........1.200V.........: [1.200V] <-- change to 1.3
    CPU PLL................1.500V.........: [1.500V] <-- change to 1.6?
    CPU Reference..........0.760V.........: [Auto]
    >>> MCH/ICH
    MCH Core...............1.100V.........: [1.200V]
    MCH Reference..........0.760V.........: [Auto]
    MCH/DRAM Reference.....0.900V.........: [Auto]
    ICH I/O................1.500V.........: [1.500V] <-- change to 1.6?
    ICH Core...............1.100V.........: [1.100V] <-- change to 1.2?
    >>> DRAM
    DRAM Voltage...........1.800V.........: [1.800V]<-- and when looking at the higher voltage settings here (2.1) it also auto changes those bottom 3 to something like 1.03
    DRAM Termination.......0.900V.........: [Auto]
    Channel A Reference....0.900V.........: [Auto]
    Channel B Reference....0.900V.........: [Auto]

    thanks again for the help
    My Rig:
    CPU: Intel E8400 Wolfdale
    Mobo: Gigabyte EP45-UD3P Rev. A3
    Bios: F8
    Power: OCZ 600 Stealth ExtremeRAM: OCZ DDR2 PC-8500 2x2Gig
    Gfx: Xfx 9800 GTX+
    Heatsink:
    Tuniq Tower 120

  10. #10
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Normal Settings for EP45-UD3P & E8400

    Don't worry about the the 2.10 volt bios setting turning red, it's Gigabytes way of saying "are you sure you know what you're doing?". Your memory can safely run at 2.15 volts if needed.

    Ignore the 0.10 volt recommend increases, this doesn't apply to your mobo, especially when running at stock speeds. You want to run with the lowest voltage settings that are fully stable. You need to perform the extended stability tests mentioned at the end of post #2. When you make bios performance changes such as memory tweaks, you'll need to repeat your stability tests to ensure that there aren't any problems.

    At your current 333MHz cpu setting, lowering Static tRead Value (aka tRD) to 6 for both memory channels (A & B) should be stable and will give you about a 3% improvement in memory performance. At 800MHz, you might be able to further improve memory performance by running your memory with tighter primary memory timings, such as 4-5-5-12 and possibly 4-4-4-12 with a 2.12 memory volt setting.

    As Chike said, you can run your memory at 1066 speeds (with looser memory timings), but you probably won't see and real world performance gains. Before you make any further bios changes, save your current bios settings as a bios profile. Page 38 in your mobo user guide describes how to save multiple bios profiles and this post has some additional information.

    Are you sure that your standard Cpu VID is 1.30 volts? As I recall, most e8400 standard cpu settings are 1.25 volts. This isn't a big deal, but there's no reason to over-volt your cpu at stock settings.

    Nice job on your screen-shots and bios posting.

    **edit** Setting Performance Enhance = Turbo should give you a slight performance gain.
    Last edited by profJim; 08-09-2009 at 04:39 PM. Reason: [more info]
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


Page 1 of 3 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •