Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 2 of 2

Thread: EX58-UD3R problems with three sticks of ram




  1. #1
    Join Date
    Apr 2008
    Posts
    20

    Default EX58-UD3R problems with three sticks of ram

    I have an issue with my new board. Running the EX58-UD3R (vers. 1.0) with i7 920 (D0), and 6GB Mushkin HP3 DDR3 1600 ram (HP3-12800 DDR3 - Mushkin Enhanced), with an Enermax Revolution+ 1050W psu. Two GTX 285s installed.

    Assembled it, and had a difficult time getting Windows installed (would get bsod message 'page Fault in non paged area'), but eventually got it running after sending 1.54v to the vdimm. Thought problem was solved. Then, after a few hours, would not boot windows again. Tried vdimm 1.6v (ram is rated for this), and no improvement. Now it won't even post with all three sticks installed, so the issue progressed. All settings at stock, and the dimms are in the proper slots. Did the following:

    1. Thought it might be a short, so I removed from the case and tried on the bench. With just one video card. No improvement. Checked the board for damage, etc.
    2. Tried 1 stick of ram. Booted fine. Rebooted a few times, and fine.
    3. Tried two sticks, booted fine. Rebooted a few times with same result.
    4. Tried 3 sticks, won't post.
    5. Tried each stick of ram on its own, and all boot to Windows no problem. Only will not post when all three are used together.

    Board is using the latest bios. You guys think the board is bad? Something I am overlooking?

    Thanks!
    EP35 DS3P (F4 bios), Q6600 @3.0GHZ, Zalman 9700, 4GB Mushkin 6400 EP, Corsair 620HX, Antec Nine Hundred (2 intake front, rear and top exhaust), Sapphire HD4870 512MB, 2X Raptor 150GB RAID 0, Xonar DX, 2X DVD Drives, Dual Boot XP Home and Vista Ultimate 64-bit

  2. #2
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: EX58-UD3R problems with three sticks of ram

    What BIOS are you using, I see you say latest but just wanted to check because that means different things to different users.

    Can you please give me your full settings, Sounds like Auto is not working for you so I need to advise you some things to manually set. Which I would advise anyway because you need to be sure you find and set your own stable QPI Voltages and this is likely the issue.

    So please fill this out and I will try to help you get going.

    This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

    0X00000050 << Incorrect Memory Timing/Freq or Uncore Multi
    0X00000124 << Incorrect QPI/Vtt Voltage (To Much/Not Enough)
    0X00000101 << Not enough Vcore Voltage

    CPU = Model #
    Motherboard = Model, Revision #
    BIOS Version =
    Ram = Brand, Model#, Part#, And or Link

    Code:
    Advanced CPU Features:
    CPU Clock Ratio ................................ [20x]
    Intel(R) Turbo Boost Tech .................. [Enabled]
    CPU Cores Enabled ............................ [All]
    CPU Multi Threading .......................... [Enabled]
    CPU Enhanced Halt (C1E) ................... [Disabled]
    C3/C6/C7 State Support .................... [Disabled]
    CPU Thermal Monitor ......................... [Enabled]
    CPU EIST Function ............................ [Disabled]
    Virtualization Technology ................... [Enabled] << Disabled if you do not use Vmware or Virtual PC Programs
    Bi-Directional PROCHOT ..................... [Enabled]
    
    
    Uncore & QPI Features:
    QPI Link Speed .............................. x36
    Uncore Frequency ..........................  (Always 2x memory Multi or 2x +1)
    Isonchronous Frequency ..................[Enabled]
    
    
    Standard Clock Control:
    Base Clock (BCLK) Control ................ [Enabled]
    BCLK Frequency (MHz) .....................
    PCI Express Frequency (MHz) ........... [100]
    
    C.I.A.2 [Disabled]
    
    Advanced Clock Control:
    CPU Clock Drive ..............................[800mV]
    PCI Express Clock Drive ................... [900mV]
    CPU Clock Skew ............................. [0ps]
    IOH Clock Skew ............................. [0ps]
    
    
    Advanced DRAM Features:
    Performance Enhance ...................... [Standard]
    Extreme Memory Profile (X.M.P) ......... [Disabled]
    System Memory Multiplier (SPD) ........ [AUTO]
    DRAM Timing Selectable (SPD) .......... [Manual]
    
    Channel A + B + C
    
    Channel A Timing Settings:
    ##Channel A Standard Timing Control##
    CAS Latency Time ......................
    tRCD .......................................
    tRP .........................................
    tRAS .......................................
    
    ##Channel A Advanced Timing Control##
    tRC ........................................  (Should be = tRAS + tRP or above for stability)
    tRRD .......................................
    tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
    tWR ........................................
    tWTP .......................................
    tWL ........................................   (tWTP Must = tWR + tWL + 4)(tWL Must be CAS Latency -1)
    tRFC .......................................
    tRTP .......................................
    tFAW ......................................
    Command Rate (CMD) ................
    
    ##Channel A Misc Timing Control##
    Round Trip Latency ...................
    
    
    
    Advanced Voltage Control:
    
    CPU
    Load Line Calibration ................. [Disabled]
    CPU Vcore ...............................
    QPI/VTT Voltage 1.150v ............
    CPU PLL 1.800v .......................
    
    MCH/ICH
    PCIE 1.500v ...........................
    QPI PLL 1.100v .......................
    IOH Core 1.100v .....................
    ICH I/O 1.500v .......................
    ICH Core 1.1v ........................
    
    DRAM
    DRAM Voltage 1.500v ..............
    DRAM Termination 0.750v [AUTO]
    Ch-A Data VRef. 0.750v [AUTO]
    Ch-B Data VRef. 0.750v [AUTO]
    Ch-C Data VRef. 0.750v [AUTO]
    Ch-A Address VRef. 0.750v [AUTO]
    Ch-B Address VRef. 0.750v [AUTO]
    Ch-C Address VRef. 0.750v [AUTO]

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •