Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 5 of 5 FirstFirst ... 345
Results 41 to 47 of 47

Thread: Overclock on GA-X48-DQ6 problem




  1. #41
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Overclock on GA-X48-DQ6 problem

    Yes, please ask if that CPU has been fully tested on this board or not. They may have just added the support and not tested it too much.
    GIGABYTE - Support&Download - Technical Service Zone

    Can you borrow, or do you have an older 775 CPU to test with?

    It also could still just be your settings. Will it boot at the speed you are trying, but all ram settings on auto and all voltages on Auto? Don't use that 24/7, I just asked to see if it would or not as Auto will give higher than need be voltages and if it does boot you will know it's just your settings is all

  2. #42
    Join Date
    Aug 2009
    Posts
    25

    Default Re: Overclock on GA-X48-DQ6 problem

    ok i will try with auto settings with 400x7.5

  3. #43
    Join Date
    Aug 2009
    Posts
    25

    Default Re: Overclock on GA-X48-DQ6 problem

    i have tried.. all auto and just enabling the FSB.. i have tried 333x7.5 and 400x7.5 both does not work at all..

  4. #44
    Join Date
    Aug 2009
    Posts
    25

    Default Re: Overclock on GA-X48-DQ6 problem

    They replied and said Q9300 is supported by X48-DQ6

  5. #45
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Overclock on GA-X48-DQ6 problem

    Ya, i know it is supported. But did you ask them if it has been fully tested?

    Do you have an older 775 CPU to test with to see if maybe the board itself is faulty? Just wondering because if so we could rule that out.

    Otherwise please post me your full settings again that is the best you can boot with

  6. #46
    Join Date
    Aug 2009
    Posts
    25

    Default Re: Overclock on GA-X48-DQ6 problem

    i do not have a old CPU.... i can only run with the default settings... whenever i change this settings it will not work

    CPU = Intel Quad 9300
    Motherboard = GA-X48-DQ6, Revision 0.1
    BIOS Version = F7
    Ram = Corsair, 2X2GB Dominator 1066Mhz , CMX2048-8500C5D,


    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [7]
    Fine Clock Ratio ____________[0.5]
    CPU Host Clock Control_ [Disable]
    CPU Host Frequency (MHz)__________ [Disable]
    PCI Express Frequency (Mhz)_______ [Auto]
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [Auto]
    DRAM Timing Selectable_______ SPD __ [Auto]

    Performance Enhance = [Standard]

    CAS Latency Time________________ 5
    Dram RAS# to CAS# Delay_________ 7
    Dram RAS# Precharge Delay_______7
    Precharge Delay (tRAS)__________24

    ACT to ACT Delay (tRRD)_________ 4
    Rank Write to READ Delay________ 4
    Write to Precharge Delay_________ 8
    Refresh to ACT Delay______________ 68
    Read to Precharge Delay__________ 4
    Static tRead Value_______________ 6
    Static tRead Phase Adjust________ [Auto]

    CPU/PCIEX Clock Driving Control [800mV]
    CPU Clock Skew Control [normal]
    GMCH Clock Skew Control [Normal]

    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [Normal]
    PCI-E OverVoltage Control_ [Normal]
    FSB OverVoltage Control___ [Normal]
    (G)MCH OverVoltage Control [Normal]
    CPU Voltage Control_______ [Normal]

  7. #47
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Overclock on GA-X48-DQ6 problem

    This does not work below?

    Do you have any other ram to test with to be sure the ram is not the issue? Have you tried clearing the CMOS Fully and then loading optimized and trying again?

    Try With F8e
    http://forum.gigabyte.de/forumdownlo...603/x48dq6.zip

    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [7]
    Fine Clock Ratio ____________[0.5]
    CPU Host Clock Control_ [Disable] << Enabled
    CPU Host Frequency (MHz)__________ [Disable] << 333
    PCI Express Frequency (Mhz)_______ [Auto] << 100
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [Auto] << 2.40 or 3.20 for 800/1066
    DRAM Timing Selectable_______ SPD __ [Auto] << Manual

    Performance Enhance = [Standard]

    CAS Latency Time________________ 5
    Dram RAS# to CAS# Delay_________ 5
    Dram RAS# Precharge Delay_______5
    Precharge Delay (tRAS)__________ 15/18

    ACT to ACT Delay (tRRD)_________ 4
    Rank Write to READ Delay________ 4
    Write to Precharge Delay_________ 8
    Refresh to ACT Delay______________ 68
    Read to Precharge Delay__________ 4
    Static tRead Value_______________ 6 << Set 7 or 8 for now
    Static tRead Phase Adjust________ [Auto]

    CPU/PCIEX Clock Driving Control [800mV]
    CPU Clock Skew Control [normal] << AUTO
    GMCH Clock Skew Control [Normal] << AUTO

    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [Normal] +0.3
    PCI-E OverVoltage Control_ [Normal] +0.1
    FSB OverVoltage Control___ [Normal] +0.1
    (G)MCH OverVoltage Control [Normal] +0.2-0.3
    CPU Voltage Control_______ [Normal] << AUTO

Page 5 of 5 FirstFirst ... 345

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •