Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 15 of 17 FirstFirst ... 51314151617 LastLast
Results 141 to 150 of 161

Thread: UD3P and Q9550 Overclock Problems




  1. #141
    Ken429 is offline Senior Member
    Join Date
    Aug 2009
    Location
    Valapariso, Indiana
    Posts
    516

    Default Re: UD3P and Q9550 Overclock Problems

    Ok, you guys finally broke me, I'm off the 2.40 memory multiplier and on to the 2.00 world. We'll see what kind of problems I can stumble into for further discussion!

  2. #142
    Ken429 is offline Senior Member
    Join Date
    Aug 2009
    Location
    Valapariso, Indiana
    Posts
    516

    Default Re: UD3P and Q9550 Overclock Problems

    I'm a slow learner. I have set the memory multiplier to 200D and Disabled LLC. I have 5-5-5-15 set for the memory with everything else set to auto except the 9 in tRD. The Vcore is set to 1.325 and the CPU Termination is set to 1.22v. At 450 FSB the system runs OCCT to completion.

    At 471 all kinds of bad things happen. I upped the Vcore to 1.35625v and the CPU Termination to 1.24v. First, I get blue screens when the CPU Termination is set to 1.24v. I watched the voltage on OCCT drop to 1.22v and then the blue screen. With the CPU Termination set to 1.20v OCCT will run for about 20 minutes and then the system hangs. OCCT is reporting a voltage of 1.26-1.30v before the system crashes. Is this a normal vdroop? Should I set the Vcore at 1.38 or 1.4v?

    As soon as I Enable LLC and set the Vcore to 1.35 and CPU Termination 1.24v OCCT seems happy running at 1.31v for 60 minutes.

    One last gasp, ProfJim can I set the Advanced Timing Control settings back to the 3-3-5-52-3-Auto using the 200D strap? Allow me one more last gasp, what is the difference between 200B and 200D?

  3. #143
    Join Date
    Jan 2009
    Location
    Sofia, Bulgaria
    Posts
    16

    Default Re: UD3P and Q9550 Overclock Problems

    Ken429, I'd tweak the Refference voltages (0.8 cpu or around that at default VTT should work well with Quads, also you should try tweaking the mch one). Hanging most of the time means not enough VTT or/and PLL voltages.
    ***
    Kick, I'm hapilly running at 500 (2000) fsb with only 1.2 on the mch DDR2 is not that expensive (but prices are going up), you can find OCZ Blade for ~130EU in Europe and mine pair can go up to 1350 mhz stable (seen others go as high as 1280-1300 with no problem).
    P45-UD3P 1.0 F10i E8400@550x8 max stable OCZ Blade LV 2x2gb 1150@1350 2v max stable

  4. #144
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: UD3P and Q9550 Overclock Problems

    When testing with 2.00D vs 2.00B, some minor tweaks might be needed.
    Your advanced memory timings look good, but they might not be compatible with the 2.00D memory strap.
    You might have better results setting these to AUTO for now, they can be tightened up later, after your system has passed stability testing.

    With different memory straps (A,B,C, or D), the bios makes "internal" changes that are appropriate for the selected memory strap.

    To avoid confusion, it's best if you post your full bios settings along with a description of the problems encountered. If you tried additional settings, it's OK to list only the changed settings and the results in the same post. It will help if you include a screen-shot with:

    1. cpu-z (CPU and Mainboard screens)
    2. Memset (including the "SPD" and ">>" tabs
    3. EasyTune6 (TUNER tab --> ADVANCE tab --> VOLTAGE)
    4. so that we can confirm some of the posted bios settings.

    I've found that the following bios settings worked best with my 996599 Mushkin memory in the mid to upper 400MHz range:
    2.00B & tRD = 8 up to 465MHz, 2.00B with tRD = 9 or 10 with higher cpu speeds
    2.00D & tRD = 9 at 480MHz up to about 500+MHz
    at mid to upper 400MHz cpu speeds:

    • MCH Core = 1.26 or 1.28
    • Cpu Termination = 1.26 or 1.28 volts
    • Cpu PLL = 1.57
    • ICH \I/O = 1.57
    • ICH Core = 1.20
    • HDD S.M.A.R.T. Capability = Disabled (Note SMART functionality will still work with other software programs)


    I suggest going back to your stable 450MHz setup and see if your system is stable using the 2.00B system memory multiplier, leaving LLC enabled.
    If it is stable, try 460MHz and higher. If necessary, set MCH Core and Cpu PLL to 1.28 volts and retest. The last 3 voltages might help with stability.

    Once you've reached your "final" stable setting, you can then see if your system is stable by disabling LLC and increasing CPU Vcore as necessary.
    Note: different memory might require different settings.

    Your vdroop seems about right with LLC disabled.
    On my system with LLC disabled:
    CPU Vcore setting: 1.3750
    PC Health seeting: 1.346 (after I've saved bios settings and exited)
    CPU @idle: ------- 1.328
    CPU @100% load:- 1.312

    Increasing MCH Reference volts 1 or 2 clicks might help with stability, as Eek suggested.

    The following information is from Lsdme's http://forums.tweaktown.com/gigabyte...-easytune.html guide.

    ===========================================
    CPU Termination (Vtt) Automatically changes the following if manually set:

    CPU Reference Voltage (63% of Default Vtt/1.20) 0.760 ET
    CPU Reference2 Voltage (67% of Default Vtt/1.20) 0.800 ET
    MCH Reference Voltage (63% of Default Vtt/1.20) 0.760 ET

    ===========================================
    DRAM Voltage Automatically changes the following if manually set:

    MCH/DRAM Reference Voltage (50% of Default Dram Voltage)
    DRAM Termination Voltage (50% of Default Dram Voltage)
    Channel A Reference Voltage (50% of Default Dram Voltage)
    Channel B Reference Voltage (50% of Default Dram Voltage)

    ===========================================
    For example if you want to try 1.28 Vtt with 0.780 MCH Ref you must:

    1) set Vtt to 1.20 first,
    2) then go set MCH Ref to 0.780
    3) Then go raise Vtt back to 1.28 and the displayed bios value for MCH Ref will self adjust.
    ================================================== ===========
    When you post your bios template and you've modified any reference volt settings, it will be best if you use the following format:

    MCH Reference..........0.760V.........: [0.808V] (0.720V with CPU Termination @ 1.200V)

    This tells us that you first set CPU termination = 1.20 (the default setting).
    Then you changed MCH Reference to 0.720 volts.
    Then you manually set CPU termination back to the desired setting.
    In this example, the bios now shows MCH Reference as 0.808.
    (Thanks to D-an-W for implementing this convention in his bios settings)
    Last edited by profJim; 09-19-2014 at 10:36 PM. Reason: fixed broken link for GTL Ref Voltages link
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  5. #145
    Ken429 is offline Senior Member
    Join Date
    Aug 2009
    Location
    Valapariso, Indiana
    Posts
    516

    Default Re: UD3P and Q9550 Overclock Problems

    ProfJim,
    I had a head start on your instructions and have run many stability tests to try and find where exactly the problems starts. Attached is the last good BIOS settings, a screen shot and a log of where I have been and where I tried to go. I took your advice and turned off LLC and upped the Vcore to compensate. I also turned off SMART. However, I hit the wall at about the same FSB as before with LLC and SMART turned on.
    Code:
    Motherboard: Model: GA-EP45-UD3P(rev 1.6) Bios Version:  FD
    Cpu: Q9550 E0
    Ram: 2X2GB Brand:  Mushkin 996559 991599 - 2GB DDR2 PC2-8500 5-5-5-15 Blackline (Module)
    Power Supply Unit: Corsair 620HX
    
    MB Intelligent Tweaker (M.I.T.)
    Robust Graphics Booster ---------------- : [Auto] 
    CPU Clock Ratio ------------------------ : [ 8 X]
    Fine CPU Clock Ratio ------------------- : [+0.5] 
    CPU Frequency -----------------------: 3.99GHz( 470X8.5)
    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control ----------------- : [Enabled]
    CPU Host Frequency (Mhz) --------------- : [ 470]    <====
    PCI Express Frequency (Mhz) ------------ : [ 100]
    C.I.A.2 -------------------------------- : [Disabled]
    Advanced Clock Control     [Press Enter]
    CPU Clock Drive ------------------------ : [ 800mV]
    PCI Express Clock Drive ---------------- : [ 900mV]
    CPU Clock Skew (ps) -------------------- : [   0ps]
    MCH Clock Skew (ps) -------------------- : [   0ps]
    DRAM Performance Control
    Performance Enhance -------------------- : [Standard]
    Extreme Memory Profile --- (X.M.P.) ---- : [Disabled]
    (G)MCH Frequency Latch ----------------- : [Auto]
    System Memory Multiplier --------------- : [2.00D]
    Memory Frequency (Mhz) -----------------: 1066 940
    DRAM Timing Selectable -(SPD)----------- : [Manual]
    Standard Timing Control
    CAS Latency Time -------- 5 ------------ : [5]  
    tRCD -------------------- 7 ------------ : [   5] 
    tRP --------------------- 7 ------------ : [   5] 
    tRAS ------------------- 24 ------------ : [  15] 
    Advanced Timing Control    [Press Enter]
    tRRD -------------------- 4 ------------ : [ 3]  
    tWTR -------------------- 4 ------------ : [ 3]  
    tWR --------------------- 8 -------------: [ 5]  
    tRFC --------------------68 ------------ : [52]  
    tRTP -------------------- 4 ------------ : [ 3]  
    Command Rate (CMD) ------ 0 -------------: [Auto]
    Channel A
    Channel A Timing Settings  [Press Enter]
    Static tRead Value ------ 8 ------------ : [ 9]  
    tRD Phase0 Adjustment --- 0 ------------ : [Auto]
    tRD Phase1 Adjustment --- 0 ------------ : [Auto]
    tRD Phase2 Adjustment --- 0 ------------ : [Auto]
    tRD Phase3 Adjustment --- 0 ------------ : [Auto]
    Trd2rd(Different Rank) -- 8 ------------ : [Auto]
    Twr2wr(Different Rank) -- 8 ------------ : [Auto]
    Twr2rd(Different Rank) -- 7 ------------ : [Auto]
    Trd2wr(Same/Diff Rank) -- 9 ------------ : [Auto]
    Dimm1 Clock Skew Control --------------- : [Auto]
    Dimm2 Clock Skew Control --------------- : [Auto]
    DDR Write Training --------------------- : [Auto]
    Channel B
    Channel B Timing Settings  [Press Enter]
    Static tRead Value ------ 8 ------------ : [ 9]  
    tRD Phase0 Adjustment --- 0 ------------ : [Auto]
    tRD Phase1 Adjustment --- 0 ------------ : [Auto]
    tRD Phase2 Adjustment --- 0 ------------ : [Auto]
    tRD Phase3 Adjustment --- 0 ------------ : [Auto]
    Trd2rd(Different Rank) -- 8 ------------ : [Auto]
    Twr2wr(Different Rank) -- 8 ------------ : [Auto]
    Twr2rd(Different Rank) -- 7 ------------ : [Auto]
    Trd2wr(Same/Diff Rank) -- 9 ------------ : [Auto]
    Dimm1 Clock Skew Control --------------- : [Auto]
    Dimm2 Clock Skew Control --------------- : [Auto]
    DDR Write Training --------------------- : [Auto]
    Channel A Driving Settings [Press Enter]
    Driving Strength Profile --------------- : [Auto]
    Data Driving Pull-Up Level ------------- : [Auto]
    Cmd  Driving Pull-Up Level ------------- : [Auto]
    Ctrl Driving Pull-Up Level ------------- : [Auto]
    Clk  Driving Pull-Up Level ------------- : [Auto]
    Data Driving Pull-Down Level ----------- : [Auto]
    Cmd  Driving Pull-Down Level ----------- : [Auto]
    Ctrl Driving Pull-Down Level ----------- : [Auto]
    Clk  Driving Pull-Down Level ----------- : [Auto]
    Channel B Driving Settings [Press Enter]
    Driving Strength Profile --------------- : [Auto]
    Data Driving Pull-Up Level ------------- : [Auto]
    Cmd  Driving Pull-Up Level ------------- : [Auto]
    Ctrl Driving Pull-Up Level ------------- : [Auto]
    Clk  Driving Pull-Up Level ------------- : [Auto]
    Data Driving Pull-Down Level ----------- : [Auto]
    Cmd  Driving Pull-Down Level ----------- : [Auto]
    Ctrl Driving Pull-Down Level ----------- : [Auto]
    Clk  Driving Pull-Down Level ----------- : [Auto]
    Motherboard Voltage Control
    CPU
    Voltage Types ----------- Normal ---------- Current
    Load-Line Calibration ------------------ : [Disabled]  <====
    CPU Vcore --------------- 1.28750V ----- : [1.38125V]  <==== 
    CPU Termination --------- 1.200V* ------ : [1.260V]    <==== 
    CPU PLL ----------------- 1.500V* ------ : [1.570V]    <====
    CPU Reference ----------- 0.760V* ------ : [0.838V]    <====
    MCH/ICH
    MCH Core ---------------- 1.100V ------- : [1.28V]     <====
    MCH Reference ----------- 0.760V ------- : [0.838V]    <====    
    MCH/DRAM Ref ------------ 0.900V ------- : [1.020V]
    ICH I/O ----------------- 1.500V ------- : [1.570V] 
    ICH Core ---------------- 1.100V ------- : [1.200V] 
    DRAM
    DRAM Voltage ------------ 1.800V ------- : [2.04V] 
    DRAM Termination -------- 0.900V ------- : [1.020V]
    Channel A Reference ----- 0.900V ------- : [Auto]
    Channel B Reference ----- 0.900V ------- : [Auto]
    Standard CMOS Features
    Floppy A ------------------------------- : [None]
    Floppy 3 Mode Support ------------------ : [Disabled]
    Advanced Settings
    Hard Disk Boot Priority ---------------- : [Press Enter]
    Quick Boot ----------------------------- : [Disabled]
    First Boot Device ---------------------- : [CDROM]
    Second Boot Device --------------------- : [Hard Disk]
    Third Boot Device ---------------------- : [Disabled]
    Boot Up Floppy Seek -------------------- : [Disabled]
    Boot up Num-Lock ----------------------- : [On]
    Password Check ------------------------- : [Setup]
    HDD S.M.A.R.T. Capability -------------- : [Disabled]   <====
    Limit CPUID Max. to 3 ------------------ : [Disabled]
    No-Execute Memory Protect -------------- : [Disabled]
    CPU Enhanced Halt (C1E) ---------------- : [Disabled]
    C2/C2E State Support ------------------- : [Disabled]
    x C4/C4E State Support ----------------- : [Disabled]
    CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
    CPU EIST Function ---------------------- : [Disabled]
    Virtualization Technology -------------- : [Disabled] 
    Display For HDD (Secs) ----------------- : [ 0]
    Full Screen LOGO Show ------------------ : [Disabled]
    Backup BIOS Image to HDD --------------- : [Disabled]
    Init Display First --------------------- : [PCI]
    Integrated Peripherals
    SATA RAID/AHCI Mode -------------------- : [Disabled]
    SATA Port0-3 Native Mode --------------- : [Disabled]
    Azalia Codec --------------------------- : [Auto]
    Onboard H/W 1394 ----------------------- : [Disabled]
    Onboard H/W LAN1 ----------------------- : [Enabled]
    Onboard H/W LAN2 ----------------------- : [Enabled]
    Green Lan ------------------------------ : [Disabled]
    Smart LAN1 ----------------------------- : [Press Enter]
    Smart LAN2 ----------------------------- : [Press Enter]
    Onboard LAN1 Boot ROM ------------------ : [Disabled]
    Onboard LAN2 Boot ROM ------------------ : [Disabled]
    Onboard SATA/IDE Device ---------------- : [Enabled]
    Onboard SATA/IDE Ctrl Mode ------------- : [IDE]
    Onboard Serial Port 1 ------------------ : [Disabled]
    Onboard Parallel Port ------------------ : [Disabled]
    X Parallel Port Mode ------------------- :  SPP
    X ECP Mode Use DMA --------------------- :  3
    USB 1.0 Controlller -------------------- : [Enabled]
    USB 2.0 Controlller -------------------- : [Enabled]
    USB Keyboard Function ------------------ : [Enabled]
    USB Mouse Function --------------------- : [Enabled]
    USB Storage Function ------------------- : [Disabled]
    PC Health Status
    Reset Case Open Status ----------------- : [Disabled]
    CPU Warning Temperature ---------------- : [70 C/150 F]
    CPU Fan Warning ------------------------ : [Disabled]
    System Fan2 Fail Warning --------------- : [Disabled]
    Power Fan Warning ---------------------- : [Disabled]
    System Fan1 Fail Warning --------------- : [Disabled]
    CPU Smart Fan Control ------------------ : [Enabled]
    CPU Samrt Fan Mode --------------------- : [PWM]
    Ran Prime95 for 6+ hours
    __________________
    I will send the spreadsheet log in the next reply.
    Last edited by Ken429; 01-18-2010 at 08:02 PM.

  6. #146
    Ken429 is offline Senior Member
    Join Date
    Aug 2009
    Location
    Valapariso, Indiana
    Posts
    516

    Default Re: UD3P and Q9550 Overclock Problems

    If you are interested.

  7. #147
    Join Date
    Jan 2009
    Location
    Sofia, Bulgaria
    Posts
    16

    Default Re: UD3P and Q9550 Overclock Problems

    I'd go up one notch on PLL and just in case set PL to 10 (might need some high vMCH for lower PL).
    ***
    profJim can you confirm if these affect stability in any way?

    • ICH Core = 1.20
    • HDD S.M.A.R.T. Capability = Disabled
    P45-UD3P 1.0 F10i E8400@550x8 max stable OCZ Blade LV 2x2gb 1150@1350 2v max stable

  8. #148
    kick's Avatar
    kick is offline Senior Member
    Join Date
    Feb 2009
    Location
    Europe,the wild wild west.
    Posts
    1,223

    Default Re: UD3P and Q9550 Overclock Problems

    Dont expect dual core fsb using a quad.
    Dont try and exceed 9-10gb/s on memory bandwith
    For me best I can get is 9 gb/s read 10 gb/s copy and write.
    that is about all the chipset will do it seems.
    What I mean is if you are around those figures and you want to run the cpu faster you may have to slacken off memory performance.
    Current Systems:

    Asrock p67 Extreme6.............. Gigabyte EP-45 UD3 ...................... Gigabyte 73 PVM S2
    Intel i5 2500k 4.8ghz................ Intel Q8400 3.8ghz......................... Intel D820 2.8ghz
    Zalman 10x cooler.................... Coolermaster V8............................ HP cooler
    8GB Gskill ripjaw ddr3.............. 4GB Gskill PI ddr2.......................... 4GB samsung ddr2
    60GB ssd/500GB HDD .............. WD 1TB hdd.................................... Seagate 160GB hdd
    GTX 460 1GB x2 SLI ................. Msi 9600GT 512MB(died) ........... Onboard gx
    Win7 64 ,750w psu(ocz)............ Win7 64 ,520w psu,seasonic...... Win XP pro ,400w psu

    HEC 6A34 case . ....................... Jeantec R2 case............................ Packard Bell case

    hoping to upgrade to http://www.thinkgeek.com/stuff/41/habicase.shtml
    http://www.flixya.com/video/140325/Animal-launching

  9. #149
    Acebmxer's Avatar
    Acebmxer is offline Gigabyte Elite
    Join Date
    May 2009
    Location
    New Jersey, United States
    Posts
    2,817

    Default Re: UD3P and Q9550 Overclock Problems

    @Ken here are my current settings for 9x475 on my q9650.

    Thats what I need to get stable with out llc on. I havent tried upping cpu term to see if i could lower vcore some. But this setting is rock solid for 24/7 use for me. Using 2.00D strap with PL 9. But going from 450 to 475 required a big jump in vcore for me.
    Main Rig
    Gigabyte z87x-OC
    Haswell i7 4770k - 4.7Ghz @ 1.330v LLC Extreme (L310B492)
    G.Skill F3-1700CL9D-8GBXM DDR3-2133mhz 9-11-10-28 1.65v @ 2800mhz 12-14-14-35 1.7v
    Samsung Green 8GB 2x4GB MV-3V4G3D/US DDR3 1.3v 30nn @ 2200Mhz 11-11-11-32 1.60v
    Sapphire ATI HD 7970 3GB clocked 1200MHz @ 1.181v.
    HiS ATI HD 6950
    Samsung 840 Pro 256GB SSD (boot Drive) on Intel sata3 controller port0
    Corsair Force GT 120 GB Sata3 SSD on Intel sata3 controller port1
    Samsung 320GB HD322GJ 7200 RPM 16M cache on Intel sata3 controller port2
    Sony Optiarc DVD-RW AD-7240S on Intel sata3 controller port5
    CORSAIR CMPSU-850TX PSU
    Swiftech MCP655-B Pump
    EK Supremacy Cpu Block
    Swiftech Mcres Micro Rev 2 Reservoir
    Black Ice GTX Xtreme 360 Radiator





  10. #150
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: UD3P and Q9550 Overclock Problems

    Excellent spreadsheet!!
    To eliminate memory settings as a possible cause at 475MHz, use the settings in column AD and change:
    CPU Host Frequency = 475Mhz.
    Set primary memory timings to AUTO, this will probably result in 5-7-7-24 settings.
    Set advanced memory timings to AUTO.
    Set tRD = 10 for memory channels A & B.
    Set Driving Strength = 1066 for memory channels A & B.

    After testing with these settings, if there are errors, set DRAM voltage to 2.00 or 2.02 volts and test again.

    You might need to increase CPU Termination (VTT).
    The general recommendation is that this should be at least 0.05 - 0.10 volts lower than CPU Vcore.
    You might need to lower the MCH Reference setting slightly with higher VTT settings.

    Many members have stated that with high overclocks, LLC = enabled is required to gain stability. I've seen a few cases where systems passed extended stability testing, but sometimes failed when their systems were at idle.

    @Eek
    ICH Core = 1.20 is what I use at 492MHz. This should help with stability at high overclocks, but Acebmxer's 1.10 setting is stable on his system.

    HDD S.M.A.R.T. Capability = Disabled
    Some have claimed that disabling SMART helps with stability. I have it disabled on my systems and my applications have no problem accessing SMART information.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


Page 15 of 17 FirstFirst ... 51314151617 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •