Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 29

Thread: Another EP45T-UD3LR with Ram Problems...




  1. #11
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Another EP45T-UD3LR with Ram Problems...

    Try this for 3.6 with ram at 1600


    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto or Fast
    CPU Clock Ratio ..........................: 9
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 3.6
    
    
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled] 
    CPU Host Frequency (Mhz) ............: 401Mhz
    PCI Express Frequency (Mhz) .........:Set to 100
    
    C.I.A.2 .................................:[Disabled]
    
    
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 
    MCH Clock Skew (ps)...................: <<< 
    
    
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 4.00D
    Memory Frequency (Mhz) ..............: 1600
    DRAM Timing Selectable ................: [Manual]
    
    Standard Timing Control
    CAS Latency Time........................7
    tRCD .........................................7
    tRP'...........................................7
    tRAS..........................................20
    
    Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
    
    Advanced Timing Control
    tRRD...........................................3-5
    tWTR.......................................... 4-8
    tWR............................................ 8-10
    tRFC........................................... 68-78
    tRTP........................................... 3-5
    Command Rate (CMD) ....................:2 << Try one last, it wont show up as working in programs that read this value, but if it boots then it works and you can compare 1-2 with benchmarks
    
    Driving Strength Profiles
    Driving Strength ............................ Highest option possible, sorry not sure if DDR3 boards offer this or not?
    
    Channel A
    Static tRead Value.........................:8-9
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Channel B
    Static tRead Value.........................:8-9
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Motherboard Voltage Control
    
    CPU
    CPU Vcore….……….........................:All up to your CPU, maybe stock but I doubt it.  Try 1.28-1.34
    
    CPU Termination…..... 1.200V*.......: << 1.225-1.34
    
    CPU PLL…………………....1.500V*.......: << 1.5-1.6
    
    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 
    
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 
    
    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.2-1.3
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.500V............: <<< 1.5
    ICH Core…………...……1.100V............: <<< 1.14
    
    DRAM
    DRAM Voltage ……....1.800V............: 1.9
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave
    
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

  2. #12
    Join Date
    Aug 2009
    Posts
    37

    Default Re: Another EP45T-UD3LR with Ram Problems...

    This is how I've actually have set my BIOS
    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 9x
    Fine CPU Clock Ratio.....................:.+.0.0
    CPU Frequency ...........................: 3.00ghz (333x9)
    
    
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled] 
    CPU Host Frequency (Mhz) ............: 400Mhz
    PCI Express Frequency (Mhz) .........:AUTO
    
    C.I.A.2 .................................:[Disabled]
    
    
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800mv
    PCI Express Clock Drive.................: 800mv
    CPU Clock Skew (ps)....................: 0ps
    MCH Clock Skew (ps)...................: 0ps
    
    
    DRAM Performance Control
    Performance Enhance...................: [Turbo]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [333]
    System Memory Multiplier ..............: 4.00b
    Memory Frequency (Mhz) ..............: 1066 1333
    DRAM Timing Selectable ................: [AUTO]
    
    Standard Timing Control
    CAS Latency Time........................7
    tRCD .........................................7
    tRP'...........................................7
    tRAS..........................................20
    
    
    
    Motherboard Voltage Control
    
    CPU
    CPU Vcore….……….........................: 1.25000V (AUTO)
    
    CPU Termination…..... 1.200V (AUTO)
    
    CPU PLL…………………....1.550V (AUTO)
    CPU Referen.…………....0.805(AUTO)
    
    
    
    MCH/ICH
    MCH Core…………….....1.100V 
    MCH Reference….…….0.760V
    ICH I/O……………….....1.550V
    ICH Core…………...……1.100V
    
    DRAM
    DRAM Voltage ……....1.500V(1840)
    DRAM Termination .…0.750V(AUTO)
    
    
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [ENABLED]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [ENABLED]
    Virtualization Technology................: [ENABLED]
    Has Passed Correctly the IntelBurn Test(standart test+10rep)
    Hope you help me to tune in correctly..
    -Intel E8400 Wolfdale + Corsair H50 + Corsair Vengeance 8gb@1600mhz + XFX HD-5770 + GIGABYTE EP45T-UD3LR/F5 BIOS rev 1.0 + Barracuda 1TB = Cooler Master CM-690II advanced


  3. #13
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

  4. #14
    Join Date
    Aug 2009
    Posts
    37

    Default Re: Another EP45T-UD3LR with Ram Problems...

    Quote Originally Posted by Lsdmeasap View Post
    So you want to leave at 3Ghz then and not 3.6 as I posted above?
    I've didnt try it yet with those paremeters...
    -Intel E8400 Wolfdale + Corsair H50 + Corsair Vengeance 8gb@1600mhz + XFX HD-5770 + GIGABYTE EP45T-UD3LR/F5 BIOS rev 1.0 + Barracuda 1TB = Cooler Master CM-690II advanced


  5. #15
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Another EP45T-UD3LR with Ram Problems...

    Ahh, ok. Please set PCIE Freq to 100, sorry I missed that in your above post.

    If you want my advice on your settings for 333 FSB, please post the settings again in full so I can advise back

  6. #16
    Join Date
    Aug 2009
    Posts
    37

    Default Re: Another EP45T-UD3LR with Ram Problems...

    Didnt work your settings for 3.6.. Put exactly as you say it, but cpu z still says cpu at 3.00ghz and ram at only 533x2
    -Intel E8400 Wolfdale + Corsair H50 + Corsair Vengeance 8gb@1600mhz + XFX HD-5770 + GIGABYTE EP45T-UD3LR/F5 BIOS rev 1.0 + Barracuda 1TB = Cooler Master CM-690II advanced


  7. #17
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Another EP45T-UD3LR with Ram Problems...

    Did it triple reboot, then you see a red warning in the MIT Section when you enter? If so that means the settings failed to load, and would not be used.

    If you only saw a double reboot then the settings worked, and maybe you left C1E and EIST Enabled?

    If things failed as mentioned first, please give me the exact settings you entered and I will advise back. Please do not say exactly as I suggested you used, because I suggested ranges for several things, please just post back what you tried

  8. #18
    Join Date
    Aug 2009
    Posts
    37

    Default Re: Another EP45T-UD3LR with Ram Problems...

    Yeah Triple Reboot and A warning in the BIOS..
    I've tried Easy Tune's quick boost Settings and Got 3.6ghz and 400mhz FSB with no errors(yet) but mem Isnt yet at 1600mhz
    -Intel E8400 Wolfdale + Corsair H50 + Corsair Vengeance 8gb@1600mhz + XFX HD-5770 + GIGABYTE EP45T-UD3LR/F5 BIOS rev 1.0 + Barracuda 1TB = Cooler Master CM-690II advanced


  9. #19
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Another EP45T-UD3LR with Ram Problems...

    OK, please post the exact setting you tried that gave you the red warning and I will advise back

  10. #20
    Join Date
    Aug 2009
    Posts
    37

    Default Re: Another EP45T-UD3LR with Ram Problems...

    Is there any way to Copy-Paste Bios Parameters in order to agilize this ??
    Cos' copying manualy into paper, the coping into PC, posting heree, etc
    to many time...

    Pc's doing fine with Easy Tune's Quick Boost at 3.6 and 3.8... But when I try to edit the ram parameters to FSB 400, 4.00D leaving timings in AUTO, and advanced parameters in AUTO, I got Triple Reboot and a Alarm Warning...
    -Intel E8400 Wolfdale + Corsair H50 + Corsair Vengeance 8gb@1600mhz + XFX HD-5770 + GIGABYTE EP45T-UD3LR/F5 BIOS rev 1.0 + Barracuda 1TB = Cooler Master CM-690II advanced


Page 2 of 3 FirstFirst 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •