Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 12 FirstFirst 1234 ... LastLast
Results 11 to 20 of 118

Thread: OCing a Q9550 on a GA-EP45-DS3R




  1. #11
    Join Date
    Sep 2009
    Location
    ohio, usa
    Posts
    94

    Default Re: OCing a Q9550 on a GA-EP45-DS3R

    ok guys here is my bios settings.
    as of now i cant pass IBT only 1 out of 5



    Code:
    Motherboard: GA-EP45-DS3R, REV 1.0, F10 BIOS
    Cpu: Q9550
    Ram: CORSAIR DDR2 1066 (PC8500)
    Power Supply Unit: CORSAIR TX650
     
     
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster -------------- : [Auto] 
    CPU Clock Ratio ---------------------- : [8]
    Fine CPU Clock Ratio ----------------- : [0.5] 
    CPU Frequency ---------------------: 425X8.5
     
    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control --------------- : [Enabled]
    CPU Host Frequency (Mhz) --------------: [425]
    PCI Express Frequency (Mhz) ---------- : [100] 
    C.I.A.2 ------------------------------ : [Disabled]
     
    Advanced Clock Control ------- [Press Enter]
    CPU Clock Drive ---------------------- : [700MV]
    PCI Express Clock Drive -------------- : [700MV]
    CPU Clock Skew (ps) ------------------ : [0PS]
    MCH Clock Skew (ps) ------------------ : [0PS]
     
    DRAM Performance Control
    Performance Enhance ------------------- : [Standard] 
    Extreme Memory Profile --- (X.M.P.) --- : [Disabled] 
    (G)MCH Frequency Latch ---------------- : [Auto]
    System Memory Multiplier -------------- : [2.00D] 
    Memory Frequency (Mhz) ---------------- : [850]
    DRAM Timing Selectable ---------------- : [Man] 
     
    Standard Timing Control
    CAS Latency Time -------- 5 --------- : [Auto]
    tRCD ------------------- 5 ---------- : [Auto]
    tRP --------------------- 5 ---------- : [Auto]
    tRAS ------------------- 15 ---------- : [Auto]
     
    Advanced Timing Control
    tRRD ------------------- 4 ---------- : [Auto]
    tWTR ------------------- 4 ---------- : [Auto]
    tWR --------------------- 8 ---------- : [Auto]
    tRFC ------------------- 68 ---------- : [Auto]
    tRTP ------------------- 4 ---------- : [Auto]
    Command Rate (CMD) -------------------- : [Auto] 
    Channel A
    Static tRead Value --------------------- : [Auto]
    tRD Phase0 Adjustment ------------------ : [Auto] 
    tRD Phase1 Adjustment ------------------ : [Auto]
    tRD Phase2 Adjustment ------------------ : [Auto]
    tRD Phase3 Adjustment ------------------ : [Auto]
    Trd2rd(Different Rank) ----------------- : [Auto]
    Twr2wr(Different Rank) ----------------- : [Auto]
    Twr2rd(Different Rank) ----------------- : [Auto]
    Trd2wr(Same/Diff Rank) ----------------- : [Auto]
    Dimm1 Clock Skew Control --------------- : [Auto] ps
    Dimm2 Clock Skew Control --------------- : [Auto] ps
     
    Channel B
    Static tRead Value --------------------- : [Auto]
    tRD Phase0 Adjustment ------------------ : [Auto]
    tRD Phase1 Adjustment ------------------ : [Auto]
    tRD Phase2 Adjustment ------------------ : [Auto]
    tRD Phase3 Adjustment ------------------ : [Auto]
    Trd2rd(Different Rank) ----------------- : [Auto]
    Twr2wr(Different Rank) ----------------- : [Auto]
    Twr2rd(Different Rank) ----------------- : [Auto]
    Trd2wr(Same/Diff Rank) ----------------- : [Auto]
    Dimm1 Clock Skew Control --------------- : [Auto] ps
    Dimm2 Clock Skew Control --------------- : [Auto] ps
     
    Motherboard Voltage Control
    CPU
    Voltage Types------------ Normal -------- Current -----
    Load-Line Calibration ----donít have this option:---- [Disabled]
    CPU Vcore --------------- 1.300v 
     
    CPU Termination --------- 1.22v 
    CPU PLL ----------------- 1.57v 
     
    CPU Reference ----------- .760v
    MCH/ICH
    MCH Core ---------------- 1.24V ------- 
    MCH Reference ----------- .760V ------- 
    MCH/DRAM Ref ------------ .900V ------ 
    ICH I/O ----------------- 1.50V ------- 
    ICH Core ---------------- ?.???V ------- : [Auto] 
    DRAM
    DRAM Voltage ------------ 2.10V ------- 
    DRAM Termination -------- .900V ------- 
    Channel A Reference ----- .900V -------
    Channel B Reference ----- .900V ------- 
     
    Advanced Settings
    Limit CPUID Max. to 3 ------------------ : [Disabled]
    No-Execute Memory Protect -------------- : [Enabled]
    CPU Enhanced Halt (C1E) ---------------- : [Disabled]
    C2/C2E State Support ------------------- : [Disabled]
    x C4/C4E State Support ----------------- : [Disabled]
    CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
    CPU EIST Function --------------------- : [Disabled]
    Virtualization Technology -------------- : [Disabled] 
     
    Integrated Peripherals
    Legacy USB Storage Detect ------------- : [Disabled] this was enabled.
    i think i need to bump my vcore some??
    GA-EP45-UD3P 1.6rev
    Q9550 @ 451x8.5 3.83ghz SLB8V 1.296 vcore in bios
    Batch #L846B715
    G-Skill ddr2 1066 2x1gb running at 1082mhz??
    OCZ Vendetta 2 with 120mm fan
    Corsair HX650w PSU with a 120mm fan
    Nvidia GeForce 8800 GTS
    WD2500AAKS
    WD3200AAKS
    WD500GB GP
    WD1001FALS
    All housed in the Big Red Hemi
    CM HAF 922 1X200MM,2X200MM RED LED & 1x140mm rear fan
    Burners=
    Sony Optaric Nec AD7220S
    Sony Optaric Nec AD7240S
    Lite-on IHAS324-9-A x2

  2. #12
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: OCing a Q9550 on a GA-EP45-DS3R

    I don't know anything about your particular board but try these settings on for size. Also what is it you want to accomplish?

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...................: Fast
    CPU Clock Ratio ...........................: 8
    Fine CPU Clock Ratio.......................: 0.5
    CPU Frequency .............................: 3613 MHz (425*8.5)
     
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control.....................: [Enabled] 
    CPU Host Frequency (Mhz) ..................: 425 MHz
    PCI Express Frequency (Mhz) ...............: 100
    C.I.A.2 ...................................: [Disabled]
    Advanced Clock Control [Press Enter]
    CPU Clock Drive............................: <<< 800
    PCI Express Clock Drive....................: <<< 900
    CPU Clock Skew (ps)........................: <<< 0ps
    MCH Clock Skew (ps)........................: <<< 0ps
    DRAM Performance Control
    Performance Enhance........................: [STANDARD]
    Extreme Memory Profile (X.M.P.)............: [Disabled]
    (G)MCH Frequency Latch.....................: [Auto]
    System Memory Multiplier ..................: [2.40B]
    Memory Frequency (Mhz) ....................: 1020
    DRAM Timing Selectable ....................: [Manual]
    Standard Timing Control
    CAS Latency Time...........................: 5
    tRCD ......................................: 5
    tRP'.......................................: 5
    tRAS.......................................: 15
    Advanced Timing Control
    tRRD.......................................: 4
    tWTR.......................................: 4
    tWR........................................: 6
    tRFC.......................................: 52
    tRTP.......................................: 4
    Command Rate (CMD) ........................: 2
    Driving Strength Profiles
    Driving Strength ..........................: 1066
    Channel A
    Static tRead Value.........................: 8
    tRD Phase0 Adjustment......................: Auto
    tRD Phase1 Adjustment......................: Auto
    tRD Phase2 Adjustment .....................: Auto
    tRD Phase3 Adjustment......................: Auto
    Trd2rd(Different Rank).....................: Auto 
    Twr2wr(Different Rank).....................: Auto 
    Twr2rd(Different Rank).....................: Auto 
    Trd2wr(Same/Diff Rank).....................: Auto 
    Dimm1 Clock Skew Control...................: Auto  ps
    Dimm2 Clock Skew Control...................: Auto  ps
    Channel B
    Static tRead Value.........................: 8
    tRD Phase0 Adjustment......................: Auto 
    tRD Phase1 Adjustment......................: Auto
    tRD Phase2 Adjustment .....................: Auto
    tRD Phase3 Adjustment......................: Auto
    Trd2rd(Different Rank).....................: Auto 
    Twr2wr(Different Rank).....................: Auto 
    Twr2rd(Different Rank).....................: Auto 
    Trd2wr(Same/Diff Rank).....................: Auto 
    Dimm1 Clock Skew Control...................: Auto  ps
    Dimm2 Clock Skew Control...................: Auto  ps
    Motherboard Voltage Control
    CPU
    Load-Line Calibration......................: [Enabled]
    CPU Vcore............1.25000V..............: 1.25000V
    CPU Termination......1.200V*...............: 1.200V
    CPU PLL..............1.500V*...............: 1.500V
    CPU Referen..........0.760V*...............: Auto
    MCH/ICH
    MCH Core.............1.100V................: 1.100V  
    MCH Reference........0.760V................: Auto
    MCH/DRAM Ref.........0.900V................: Auto
    ICH I/O..............1.500V................: 1.500V
    ICH Core.............1.100V................: 1.100v
    DRAM
    DRAM Voltage ........2.000V................: 2.100V
    DRAM Termination.....0.900V................: Auto
    Channel A Reference..0.900V................: Auto
    Channel B Reference..0.900V................: Auto
    Advanced Settings
    Limit CPUID Max. to 3......................: [Disabled]
    No-Execute Memory Protect..................: [Enabled]
    CPU Enhanced Halt (C1E)....................: [Disabled]
    C2/C2E State Support.......................: [Disabled]
    x C4/C4E State Support.....................: [Disabled]
    CPU Thermal Monitor 2(TM2) ................: [Enabled]
    CPU EIST Function..........................: [Enabled]
    Virtualization Technology..................: [Disabled] Enabled if you use Vmware/Virtual PC
    Integrated Peripherals
    Legacy USB Storage Detect .................: [Enabled] *Note* Must be enabled to flash from USB

  3. #13
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: OCing a Q9550 on a GA-EP45-DS3R

    It seems you have not began by loading optimized defaults, it is recommended to begin with optimized defaults, not failsafe defaults.
    The settings seems within erason but there's no realy way to tell, what is default vcore? (the number on the left)
    There are newr version of IBT, latest is v2.3 if i am not mistaken, it would be easier seeing it's screen capture.
    Leave the reference voltages on auto for now, unless you are sure the changes are needed of course.
    Have you tried the same FSB with lower CPU Ratio?

  4. #14
    Join Date
    Sep 2009
    Location
    ohio, usa
    Posts
    94

    Default Re: OCing a Q9550 on a GA-EP45-DS3R

    well since posting that i cant get it stable in IBT. ive taken mch up to 1.3v vcore up to 1.3375v dram volts up to 2.3v it will pass 1/2 mem but at 100% mem it will only pass 3of 5

    ill go and set it to optimized defaults. and start over. with the code sheet

    tbh right now all i want to do is get it stable at the 3.6ghz but ultimately want 3.83ghz

    here is ET6 on the last settings i was working with. i havent gone into bios and changed them from MY original settings

    GA-EP45-UD3P 1.6rev
    Q9550 @ 451x8.5 3.83ghz SLB8V 1.296 vcore in bios
    Batch #L846B715
    G-Skill ddr2 1066 2x1gb running at 1082mhz??
    OCZ Vendetta 2 with 120mm fan
    Corsair HX650w PSU with a 120mm fan
    Nvidia GeForce 8800 GTS
    WD2500AAKS
    WD3200AAKS
    WD500GB GP
    WD1001FALS
    All housed in the Big Red Hemi
    CM HAF 922 1X200MM,2X200MM RED LED & 1x140mm rear fan
    Burners=
    Sony Optaric Nec AD7220S
    Sony Optaric Nec AD7240S
    Lite-on IHAS324-9-A x2

  5. #15
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: OCing a Q9550 on a GA-EP45-DS3R

    Always make changes in your bios, ET6 sucks eggs...

  6. #16
    Join Date
    Sep 2009
    Location
    ohio, usa
    Posts
    94

    Default Re: OCing a Q9550 on a GA-EP45-DS3R

    ET6 isnt the best i agree.i was just testing the settings with it then was going to bios and change them.

    well with loading optimised defaults. and i used the settings from the template above that you posted. it isnt stable at 100%mem but is at 1/2 at full mem it did respond better. i think maybe some more dram voltage might help or should i work on mch????? here is a screen of CPUZ IBT and real temp



    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...................: Fast
    CPU Clock Ratio ...........................: 8
    Fine CPU Clock Ratio.......................: 0.5
    CPU Frequency .............................: 3613 MHz (425*8.5)
     
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control.....................: [Enabled] 
    CPU Host Frequency (Mhz) ..................: 425 MHz
    PCI Express Frequency (Mhz) ...............: 100
    C.I.A.2 ...................................: [Disabled]
    Advanced Clock Control [Press Enter]
    CPU Clock Drive............................: <<< 800
    PCI Express Clock Drive....................: <<< 900
    CPU Clock Skew (ps)........................: <<< 0ps
    MCH Clock Skew (ps)........................: <<< 0ps
    DRAM Performance Control
    Performance Enhance........................: [STANDARD]
    Extreme Memory Profile (X.M.P.)............: [Disabled]
    (G)MCH Frequency Latch.....................: [Auto]
    System Memory Multiplier ..................: [2.40B]
    Memory Frequency (Mhz) ....................: 1020
    DRAM Timing Selectable ....................: [Manual]
    Standard Timing Control
    CAS Latency Time...........................: 5
    tRCD ......................................: 5
    tRP'.......................................: 5
    tRAS.......................................: 15
    Advanced Timing Control
    tRRD.......................................: 4
    tWTR.......................................: 4
    tWR........................................: 6
    tRFC.......................................: 52
    tRTP.......................................: 4
    Command Rate (CMD) ........................: 2
    Driving Strength Profiles
    Driving Strength ..........................: 1066
    Channel A
    Static tRead Value.........................: 8
    tRD Phase0 Adjustment......................: Auto
    tRD Phase1 Adjustment......................: Auto
    tRD Phase2 Adjustment .....................: Auto
    tRD Phase3 Adjustment......................: Auto
    Trd2rd(Different Rank).....................: Auto 
    Twr2wr(Different Rank).....................: Auto 
    Twr2rd(Different Rank).....................: Auto 
    Trd2wr(Same/Diff Rank).....................: Auto 
    Dimm1 Clock Skew Control...................: Auto  ps
    Dimm2 Clock Skew Control...................: Auto  ps
    Channel B
    Static tRead Value.........................: 8
    tRD Phase0 Adjustment......................: Auto 
    tRD Phase1 Adjustment......................: Auto
    tRD Phase2 Adjustment .....................: Auto
    tRD Phase3 Adjustment......................: Auto
    Trd2rd(Different Rank).....................: Auto 
    Twr2wr(Different Rank).....................: Auto 
    Twr2rd(Different Rank).....................: Auto 
    Trd2wr(Same/Diff Rank).....................: Auto 
    Dimm1 Clock Skew Control...................: Auto  ps
    Dimm2 Clock Skew Control...................: Auto  ps
    Motherboard Voltage Control
    CPU
    Load-Line Calibration......................: [Enabled] i dont have this option.
    CPU Vcore............1.25000V..............: 1.25000V
    CPU Termination......1.200V*...............: 1.200V
    CPU PLL..............1.500V*...............: 1.500V
    CPU Referen..........0.760V*...............: Auto
    MCH/ICH
    MCH Core.............1.100V................: 1.100V  
    MCH Reference........0.760V................: Auto
    MCH/DRAM Ref.........0.900V................: Auto
    ICH I/O..............1.500V................: 1.500V
    ICH Core.............1.100V................: 1.100v
    DRAM
    DRAM Voltage ........2.000V................: 2.100V
    DRAM Termination.....0.900V................: Auto
    Channel A Reference..0.900V................: Auto
    Channel B Reference..0.900V................: Auto
    Advanced Settings
    Limit CPUID Max. to 3......................: [Disabled]
    No-Execute Memory Protect..................: [Enabled]
    CPU Enhanced Halt (C1E)....................: [Disabled]
    C2/C2E State Support.......................: [Disabled]
    x C4/C4E State Support.....................: [Disabled]
    CPU Thermal Monitor 2(TM2) ................: [Enabled]
    CPU EIST Function..........................: [Enabled]
    Virtualization Technology..................: [Enabled] 
    Integrated Peripherals
    Legacy USB Storage Detect .................: [Enabled]
    GA-EP45-UD3P 1.6rev
    Q9550 @ 451x8.5 3.83ghz SLB8V 1.296 vcore in bios
    Batch #L846B715
    G-Skill ddr2 1066 2x1gb running at 1082mhz??
    OCZ Vendetta 2 with 120mm fan
    Corsair HX650w PSU with a 120mm fan
    Nvidia GeForce 8800 GTS
    WD2500AAKS
    WD3200AAKS
    WD500GB GP
    WD1001FALS
    All housed in the Big Red Hemi
    CM HAF 922 1X200MM,2X200MM RED LED & 1x140mm rear fan
    Burners=
    Sony Optaric Nec AD7220S
    Sony Optaric Nec AD7240S
    Lite-on IHAS324-9-A x2

  7. #17
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: OCing a Q9550 on a GA-EP45-DS3R

    Lower CPU Ratio to isolate the problem.
    Probably more MCH Core and maybe vtt. See what BIOS HWMonitor read for DRAM voltage, perheps you can set less, it is currently slightly underclocked.

  8. #18
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: OCing a Q9550 on a GA-EP45-DS3R

    I'd up v core a notch or 2 1st.

  9. #19
    Join Date
    Sep 2009
    Location
    ohio, usa
    Posts
    94

    Default Re: OCing a Q9550 on a GA-EP45-DS3R

    ill do some more tweaking in a bit. time for a break been looking at bios for 3 hours now..lol thanks for all the help. and keep it coming..lol

    ok took just Vcore up from 1.250v to 1.2625v and it made a difference. IBT stable at full mem stress.


    here is my current settings. going to run occt,orthos, and get the quad ready prime95 and run it.

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...................: Fast
    CPU Clock Ratio ...........................: 8
    Fine CPU Clock Ratio.......................: 0.5
    CPU Frequency .............................: 3613 MHz (425*8.5)
     
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control.....................: [Enabled] 
    CPU Host Frequency (Mhz) ..................: 425 MHz
    PCI Express Frequency (Mhz) ...............: 100
    C.I.A.2 ...................................: [Disabled]
    Advanced Clock Control [Press Enter]
    CPU Clock Drive............................: <<< 800
    PCI Express Clock Drive....................: <<< 900
    CPU Clock Skew (ps)........................: <<< 0ps
    MCH Clock Skew (ps)........................: <<< 0ps
    DRAM Performance Control
    Performance Enhance........................: [STANDARD]
    Extreme Memory Profile (X.M.P.)............: [Disabled]
    (G)MCH Frequency Latch.....................: [Auto]
    System Memory Multiplier ..................: [2.40B]
    Memory Frequency (Mhz) ....................: 1020
    DRAM Timing Selectable ....................: [Manual]
    Standard Timing Control
    CAS Latency Time...........................: 5
    tRCD ......................................: 5
    tRP'.......................................: 5
    tRAS.......................................: 15
    Advanced Timing Control
    tRRD.......................................: 4
    tWTR.......................................: 4
    tWR........................................: 6
    tRFC.......................................: 52
    tRTP.......................................: 4
    Command Rate (CMD) ........................: 2
    Driving Strength Profiles
    Driving Strength ..........................: 1066--not a option on my board.
    Channel A
    Static tRead Value.........................: 8
    tRD Phase0 Adjustment......................: Auto
    tRD Phase1 Adjustment......................: Auto
    tRD Phase2 Adjustment .....................: Auto
    tRD Phase3 Adjustment......................: Auto
    Trd2rd(Different Rank).....................: Auto 
    Twr2wr(Different Rank).....................: Auto 
    Twr2rd(Different Rank).....................: Auto 
    Trd2wr(Same/Diff Rank).....................: Auto 
    Dimm1 Clock Skew Control...................: Auto  ps
    Dimm2 Clock Skew Control...................: Auto  ps
    Channel B
    Static tRead Value.........................: 8
    tRD Phase0 Adjustment......................: Auto 
    tRD Phase1 Adjustment......................: Auto
    tRD Phase2 Adjustment .....................: Auto
    tRD Phase3 Adjustment......................: Auto
    Trd2rd(Different Rank).....................: Auto 
    Twr2wr(Different Rank).....................: Auto 
    Twr2rd(Different Rank).....................: Auto 
    Trd2wr(Same/Diff Rank).....................: Auto 
    Dimm1 Clock Skew Control...................: Auto  ps
    Dimm2 Clock Skew Control...................: Auto  ps
    Motherboard Voltage Control
    CPU
    Load-Line Calibration......................: [Enabled] i dont have this option.
    CPU Vcore............1.25000V..............: 1.2625V
    CPU Termination......1.200V*...............: 1.200V
    CPU PLL..............1.500V*...............: 1.500V
    CPU Referen..........0.760V*...............: Auto
    MCH/ICH
    MCH Core.............1.100V................: 1.100V  
    MCH Reference........0.760V................: Auto
    MCH/DRAM Ref.........0.900V................: Auto
    ICH I/O..............1.500V................: 1.500V
    ICH Core.............1.100V................: 1.100v
    DRAM
    DRAM Voltage ........2.000V................: 2.100V
    DRAM Termination.....0.900V................: Auto
    Channel A Reference..0.900V................: Auto
    Channel B Reference..0.900V................: Auto
    Advanced Settings
    Limit CPUID Max. to 3......................: [Disabled]
    No-Execute Memory Protect..................: [Enabled]
    CPU Enhanced Halt (C1E)....................: [Disabled]
    C2/C2E State Support.......................: [Disabled]
    x C4/C4E State Support.....................: [Disabled]
    CPU Thermal Monitor 2(TM2) ................: [Enabled]
    CPU EIST Function..........................: [Enabled]
    Virtualization Technology..................: [Enabled] 
    Integrated Peripherals
    Legacy USB Storage Detect .................: [Enabled]
    Last edited by cincyrob; 09-28-2009 at 10:58 AM.
    GA-EP45-UD3P 1.6rev
    Q9550 @ 451x8.5 3.83ghz SLB8V 1.296 vcore in bios
    Batch #L846B715
    G-Skill ddr2 1066 2x1gb running at 1082mhz??
    OCZ Vendetta 2 with 120mm fan
    Corsair HX650w PSU with a 120mm fan
    Nvidia GeForce 8800 GTS
    WD2500AAKS
    WD3200AAKS
    WD500GB GP
    WD1001FALS
    All housed in the Big Red Hemi
    CM HAF 922 1X200MM,2X200MM RED LED & 1x140mm rear fan
    Burners=
    Sony Optaric Nec AD7220S
    Sony Optaric Nec AD7240S
    Lite-on IHAS324-9-A x2

  10. #20
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: OCing a Q9550 on a GA-EP45-DS3R

    If you use this Intel Burn Test v2.3 you'll find it much better than the one your using.
    Last edited by Conners; 09-28-2009 at 11:12 AM.

Page 2 of 12 FirstFirst 1234 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •