Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 10 FirstFirst 1234 ... LastLast
Results 11 to 20 of 93

Thread: Wow, you guys are awesome




  1. #11
    Join Date
    Oct 2009
    Location
    Atlanta
    Posts
    78

    Default This looks seriously fatal

    Returning from a few days away, I found my system in a BSOD, waiting for input. I tried the reset button but experienced the same sequence described above - long pause on the splash screen, HD activity light on steady and then a boot disk failure message. I powered it down and cold booted and it came up OK. Then overnight, it BSODed again and now it won't reboot no matter what.

    I inserted a Seagate test CD and forced a boot from the CD. The Seagate utility could not find a hard drive.

    I inserted a Windows 7 recovery CD and again tried to force a boot from the CD but now it won't boot from that CD either.

    I think I have found the problem. I knew from reading here and elsewhere that the first instruction was going to be "check all the power cables and SATA cables". So I opened up the case and checked and checked and did not find any loose connections. So I hit the power button again and saw the following:

    The CPU cooling fan was not starting. It would move a little bit, but not spin up. I gave it a little nudge and it took off. Then I noticed that one of the three cooling fans on the Corsair memory cooling array was turning slowly. I tired "helping" it also but to no avail. It kept turning somewhat slowly and erratically.

    So I removed the memory cooling fans and tried again. This time, the CPU fan still needed some help to get going but I was again able to give it a little nudge and get it running. then the system booted normally.

    So my theory is that the sticky fans are pulling the system voltage down somehow and messing with other subsystems on the board. I will get a new CPU cooler and contact Corsair regarding the memory cooling fans. I'm not sure they are necessary as there are many other fans in the system - two inlet fans to the case, one large exhaust fan from the case and the fans on the power supply and graphics card.

    Comments? Suggestions?
    EP45-UD3LR Rev. 1.0
    Bios version F10 dated 1/27/2010
    Q9550 @ 2.83GHz with the cooling fan supplied w/processor
    PSU Corsair TX750W
    NVIDIA GeForce GTS 250
    Seagate SATA Barracuda 7200.11 1.5TB
    Hitachi SATA Deskstar 7K1000.C 1.0TB
    Samsung SATA 20x DVD/RW
    Corsair DDR2 CM2X2048-8500C5D

  2. #12
    Join Date
    Oct 2009
    Location
    Atlanta
    Posts
    78

    Default Ooops

    After a minutes just idling, not doing anything with it:

    "STOP: c000021a {Fatal System Error}
    The windows subsystem system process terminated unexpectedly with a status of 0xc0000006 (0xfdc031b0 0x00a1f150).
    The system has been shut down"

    EP45-UD3LR Rev. 1.0
    Bios version F10 dated 1/27/2010
    Q9550 @ 2.83GHz with the cooling fan supplied w/processor
    PSU Corsair TX750W
    NVIDIA GeForce GTS 250
    Seagate SATA Barracuda 7200.11 1.5TB
    Hitachi SATA Deskstar 7K1000.C 1.0TB
    Samsung SATA 20x DVD/RW
    Corsair DDR2 CM2X2048-8500C5D

  3. #13
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Wow, you guys are awesome

    So how would you like your crow served?
    raw? medium-rare? well done?
    Don't feel too bad, read the last half of the first line in my forum signature.

    The problem with not doing extended stress testing is that a system that isn't fully stable can result in data or file corruption.

    Follow steps 1 - 4 in this post to provide the information we need.
    If you are running stock memory and cpu speeds, your system will probably be stable using the recommended settings in the post.

    Update the information in your signature to include the bios and motherboard versions and include a link to your memory's specifications.
    Use the generic bios template in this post to provide your current bios settings.

    Let us know if you want some help with running Intel BurnTest, Linx, Prime95 or other stress testing programs.
    Last edited by profJim; 02-12-2010 at 06:57 PM.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  4. #14
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: Wow, you guys are awesome

    Maybe your PSU is dying?
    Check PC Health status voltages.

  5. #15
    Join Date
    Oct 2009
    Location
    Atlanta
    Posts
    78

    Default Re: Wow, you guys are awesome

    The system is running at the moment after being completely shut down for about 24 hours. I'll get to work on the stuff you asked for.

    I found this pretty interesting. When I google the exact error message I got, "The windows subsystem system process terminated unexpectedly with a status of 0xc0000006 (0xfdc031b0 0x00a1f150)", I only get one hit which is my post here. In all of googleland, nobody else has ever posted that message. I don't know whether to be terrified or proud.
    EP45-UD3LR Rev. 1.0
    Bios version F10 dated 1/27/2010
    Q9550 @ 2.83GHz with the cooling fan supplied w/processor
    PSU Corsair TX750W
    NVIDIA GeForce GTS 250
    Seagate SATA Barracuda 7200.11 1.5TB
    Hitachi SATA Deskstar 7K1000.C 1.0TB
    Samsung SATA 20x DVD/RW
    Corsair DDR2 CM2X2048-8500C5D

  6. #16
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Wow, you guys are awesome

    Google search using 0xc000021a has many links to possible solutions.
    Let us know if this helps after you've become an 0xc000021a expert.
    **edit** Be proud and terrified.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  7. #17
    Join Date
    Oct 2009
    Location
    Atlanta
    Posts
    78

    Default Re: Wow, you guys are awesome

    OK, here goes:

    BIOS INFO

    CPU = Q9550
    Motherboard = EP45-UD3LR Rev. 1.0
    BIOS Version = F7
    Ram = Corsair TWIN2X4096-8500C5DF

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 8x
    Fine CPU Clock Ratio.....................: +0.5
    CPU Frequency ...........................: 2.83GHz (333 x 8.5)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: Disabled
    CPU Host Frequency (Mhz) ............: Mhz 333
    PCI Express Frequency (Mhz) .........: Auto

    C.I.A.2 .................................:Disabled


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 800
    CPU Clock Skew (ps)....................: <<< 0 ps
    MCH Clock Skew (ps)...................: <<< 0 ps


    DRAM Performance Control
    Performance Enhance...................: TURBO
    Extreme Memory Profile (X.M.P.).....: Auto
    (G)MCH Frequency Latch...............: Auto
    System Memory Multiplier ..............: Auto
    Memory Frequency (Mhz) ..............: 1066
    DRAM Timing Selectable ................: Auto

    Standard Timing Control
    CAS Latency Time........................5
    tRCD .........................................5
    tRP'...........................................5
    tRAS..........................................15

    Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

    Advanced Timing Control
    tRRD...........................................4
    tWTR..........................................4
    tWR............................................8
    tRFC...........................................68
    tRTP...........................................4
    Command Rate (CMD) ....................:0

    Driving Strength Profiles
    Driving Strength ............................

    Channel A
    Static tRead Value........................Auto 6
    tRD Phase0 Adjustment...................:Auto 0
    tRD Phase1 Adjustment...................:Auto 0
    tRD Phase2 Adjustment .................:Auto 0
    tRD Phase3 Adjustment..................:Auto 0
    Trd2rd(Different Rank)....................:Auto 8
    Twr2wr(Different Rank)...................:Auto 8
    Twr2rd(Different Rank)...................:Auto 7
    Trd2wr(Same/Diff Rank)..................:Auto 9
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto
    DPR Write training.....................:Auto

    Channel B
    Static tRead Value.........................:Auto 6
    tRD Phase0 Adjustment...................:Auto 0
    tRD Phase1 Adjustment...................:Auto 0
    tRD Phase2 Adjustment .................:Auto 0
    tRD Phase3 Adjustment..................:Auto 0
    Trd2rd(Different Rank)....................:Auto 8
    Twr2wr(Different Rank)...................:Auto 8
    Twr2rd(Different Rank)...................:Auto 7
    Trd2wr(Same/Diff Rank)..................:Auto 9
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto
    DPR Write training.....................:Auto

    Motherboard Voltage Control

    CPU
    CPU Vcore….……….........................:Auto 1.15

    CPU Termination…..... 1.200V*.......: Auto 1.2

    CPU PLL…………………....1.500V*.......: Auto 1.55

    CPU Referen.…………....0.755V*.......: Auto 0.805

    CPU Reference2………,,0.800V*.......: NOT PRESENT

    MCH/ICH
    MCH Core…………….....1.100V...........: Auto 1.1
    MCH Reference….…….0.760V...........: Auto 0.76
    MCH/DRAM Ref.…......0.900V...........: NOT PRESENT
    ICH I/O……………….....1.500V............: Auto 1.55
    ICH Core…………...……1.100V............: Auto 1.1

    DRAM
    DRAM Voltage ……....1.800V............: 1.86
    DRAM Termination .…0.900V............: NOT PRESENT
    Channel A Reference 0.900V............: NOT PRESENT
    Channel B Reference 0.900V............: NOT PRESENT

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Enabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Enabled]
    Virtualization Technology................: [Enabled] I am NOT using VMWare or Virtual PC

    Integrated Peripherals
    Legacy USB Storage Detect ..............[Enabled]

    And the screen shots:







    EP45-UD3LR Rev. 1.0
    Bios version F10 dated 1/27/2010
    Q9550 @ 2.83GHz with the cooling fan supplied w/processor
    PSU Corsair TX750W
    NVIDIA GeForce GTS 250
    Seagate SATA Barracuda 7200.11 1.5TB
    Hitachi SATA Deskstar 7K1000.C 1.0TB
    Samsung SATA 20x DVD/RW
    Corsair DDR2 CM2X2048-8500C5D

  8. #18
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Wow, you guys are awesome

    When you post your bios settings, the value in the far right column should only have one setting, not 2 settings.

    Static tRead Value........................Auto 6
    CPU Vcore….……….........................:Auto 1.15

    To avoid confusion, these should be:
    Static tRead Value........................: [Auto]
    CPU Vcore….……….........................: [Auto]
    or:
    Static tRead Value........................: [6]
    CPU Vcore….……….........................: [1.15000]

    Sometimes systems will have boot loop or stability issues, even with optimized bios default settings and no overclock.

    Using the recommended settings in this post often eliminates problems with systems running at stock speeds.
    I strongly recommend that you manually change the listed settings in the post to the values displayed in your bios to the left of the [Auto] column.
    MCH Core and Dram Voltage usually have to be manually set based on how much memory you are using.
    The cpu-z SPD shows that 2.10 volts is required to run your memory at 1066 speeds. ET6 shows that the bios has automatically set Dram Voltage to on 1.86 volts. This might be a cause of your BSOD.

    Even with a brand new motherboard or other new hardware, extended stress/stability testing should be run to ensure that there are no hardware problems than can lead to system problems, such as BSODs, crashes, freezing or data/file corruption.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  9. #19
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: Wow, you guys are awesome

    Quote Originally Posted by profJim View Post
    The cpu-z SPD shows that 2.10 volts is required to run your memory at 1066 speeds. ET6 shows that the bios has automatically set Dram Voltage to on 1.86 volts. This might be a cause of your BSOD.
    Nah, BIOS never set DRAM Voltage 1.86v automatically, this is set manually.

  10. #20
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Wow, you guys are awesome

    DRAM Voltage ……....1.800V............: 1.86
    oops, I missed this entry in his posted bios settings, never mind ;)
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


Page 2 of 10 FirstFirst 1234 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •