Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 28

Thread: Need Help Setting Bios for GA-EP45-UD3LR And Q9550




  1. #11
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: Need Help Setting Bios for GA-EP45-UD3LR And Q9550

    There is nothing wrong with a vid of 1.3 (and that refers to your Q9550 voltage) it's just on the high end that's all. Some are low, med and high vid. Just a WAG but I've seen any there from like 1.22 to your 1.3, I have 1.25.

    And this I assume is 900 mV and not 800 mV as the manual states as default.

    Anyway here are a few suggestions for you to try on for size. Replace with whats after the <--

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster -------------- : [AUTO]
    CPU Clock Ratio ---------------------- : [8]
    Fine CPU Clock Ratio ----------------- : [0.5]
    CPU Frequency ------------------------ : 2.8 GHz
    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control --------------- : [Disabled]
    CPU Host Frequency (Mhz) --------------: [333Mhz]
    PCI Express Frequency (Mhz) ---------- : 100
    C.I.A.2 ------------------------------ : [Disabled]
    Advanced Clock Control ------- [Press Enter]
    CPU Clock Drive ---------------------- : [800 mV]
    PCI Express Clock Drive -------------- : [900 mV]  <--800 mV or 900mV
    CPU Clock Skew (ps) ------------------ : [0ps]
    MCH Clock Skew (ps) ------------------ : [0ps]
    DRAM Performance Control
    Performance Enhance ------------------- : [Standard]
    Extreme Memory Profile --- (X.M.P.) --- : [Disabled]
    (G)MCH Frequency Latch ---------------- : [Auto]
    System Memory Multiplier -------------- : [3.20B]
    Memory Frequency (Mhz) ---------------- : 1066
    DRAM Timing Selectable ---------------- : [Manual]
    Standard Timing Control
    CAS Latency Time ------- ? 5 ?-------- : [5]
    tRCD ------------------- ? 7 ?-------- : [5]
    tRP -------------------- ? 7 ?-------- : [5]
    tRAS ------------------- ? 24 ?-------- : [15]
    
    You can leave the below on auto for now if you like
    Advanced Timing Control
    tRRD ------------------- ? 4 ? ------- : [4]
    tWTR ------------------- ? 4 ? ------- : [6] <--4
    tWR -------------------- ? 8 ? ------- : [6] 
    tRFC ------------------- ? 68 ? ------- : [62]
    tRTP ------------------- ? 4 ? ------- : [5] <--4
    Command Rate (CMD) -------------------- : [2]
    Driving Strength Profiles
    Channel A Driving Strength ------------ : 1066
    Channel B Driving Strength ------------ : 1066
    Channel A
    Static tRead Value ---------? 6 ?------- : [9] <--8
    tRD Phase0 Adjustment ------? 0 ?------- : [Auto]
    tRD Phase1 Adjustment ------? 0 ?------- : [Auto]
    tRD Phase2 Adjustment ------? 0 ?------- : [Auto]
    tRD Phase3 Adjustment ------? 0 ?------- : [Auto]
    Trd2rd(Different Rank) -----? 8 ?------- : [Auto]
    Twr2wr(Different Rank) -----? 8 ?------- : [Auto]
    Twr2rd(Different Rank) -----? 7 ?------- : [Auto]
    Trd2wr(Same/Diff Rank) -----? 9 ?------- : [Auto]
    Dimm1 Clock Skew Control --------------- : [Auto]
    Dimm2 Clock Skew Control --------------- : [Auto]
    Channel B
    Static tRead Value ---------? 6 ?------- : [9] <--8
    tRD Phase0 Adjustment ------? 0 ?------- : [Auto]
    tRD Phase1 Adjustment ------? 0 ?------- : [Auto]
    tRD Phase2 Adjustment ------? 0 ?------- : [Auto]
    tRD Phase3 Adjustment ------? 0 ?------- : [Auto]
    Trd2rd(Different Rank) -----? 8 ?------- : [Auto]
    Twr2wr(Different Rank) -----? 8 ?------- : [Auto]
    Twr2rd(Different Rank) -----? 7 ?------- : [Auto]
    Trd2wr(Same/Diff Rank) -----? 9 ?------- : [Auto]
    Dimm1 Clock Skew Control --------------- : [Auto]
    Dimm2 Clock Skew Control --------------- : [Auto]
    Motherboard Voltage Control
    CPU
    Voltage Types------------ Normal -------- Current -----
    Load-Line Calibration ----------------- : [Disabled]
    CPU Vcore --------------- 1.30000 ----- : [AUTO] <--1.3000
    CPU Termination --------- 1.200V------- : [1.220] <--Auto
    CPU PLL ----------------- 1.550V ------ : [1.550] <--Auto
    CPU Reference ----------- 0.805V ------ : [Auto]
    MCH/ICH
    MCH Core ---------------- 1.100V ------- : [1.20] <--1.10
    MCH Reference ----------- 0.760V ------- : [Auto]
    ICH I/O ----------------- 1.5500V ------- : [1.550V] <--Auto
    ICH Core ---------------- 1.100V ------- : [Auto]
    DRAM
    DRAM Voltage ------------ 1.800V ------- : [2.100]
    DRAM Termination -------- 0.900V ------- : [Auto]
    Channel A Reference ----- 0.900V ------- : [Auto]
    Channel B Reference ----- 0.900V ------- : [Auto]
    Advanced Settings
    Limit CPUID Max. to 3 ------------------ : [Disabled]
    No-Execute Memory Protect -------------- : [Enabled]
    CPU Enhanced Halt (C1E) ---------------- : [Disabled]
    C2/C2E State Support ------------------- : [Disabled]
    x C4/C4E State Support ----------------- : [Disabled]
    CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
    CPU EIST Function ---------------------- : [Disabled]
    Virtualization Technology -------------- : [Enabled]
    Integrated Peripherals
    Legacy USB Storage Detect -------------- : [Enabled]

  2. #12
    Join Date
    Nov 2009
    Location
    Jakarta
    Posts
    16

    Default Re: Need Help Setting Bios for GA-EP45-UD3LR And Q9550

    And this I assume is 900 mV and not 800 mV as the manual states as default.

    For the PCI Express Clock Drive default from the computer is 800mV

    Anyway here are a few suggestions for you to try on for size. Replace with whats after the <--

    well thanks for the suggestion, I have already tried them, but the problem still remain the same, it's ok for easy browsing, office doc, but not for gaming.
    it's stuck and freeze again. no blue screen, just freeze
    Components:

    Motherboard : GA-EP45-UD3LR: Rev#:1.0

    BIOS Version : F7

    CPU : Intel Core 2 Quad 9550

    Ram :
    Corsair Dominator 4GB (2 x 2 GB) DDR2 1066 (PC2 8500) Twin2x4096-8500C5DF

    Power Supply : SeaSonic M12II-500Bronze(SS-500GM Active PFC)

    Video Card: Manli Nvidia GeForce 9800 (512MB
    DDR3)

    Sound Card: Internal

    Cooling System: Corsair H50

    Hard Drives: WD Green SATA2-(750GB)

  3. #13
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: Need Help Setting Bios for GA-EP45-UD3LR And Q9550

    Up CPU Reference on notch and test the try two notches up from .805. Do the same thing with MCH reference voltage. I neither of those seem to work up the CPU term one or two
    notches and you can also try MCH Core up one or two notches.

  4. #14
    Join Date
    Nov 2009
    Location
    Jakarta
    Posts
    16

    Default Re: Need Help Setting Bios for GA-EP45-UD3LR And Q9550

    Up CPU Reference on notch and test the try two notches up from .805. Do
    the same thing with MCH reference voltage. I neither of those seem to
    work up the CPU term one or two

    notches and you can also try MCH Core up one or two notches.

    OK I will try them tonight
    CPU Reference ----------- 0.805V ------ : up 1 or 2 notch

    MCH Reference ----------- 0.760V ------ : up 1 or 2 notch

    I will update the result later.

    Thanks
    </pre>
    Components:

    Motherboard : GA-EP45-UD3LR: Rev#:1.0

    BIOS Version : F7

    CPU : Intel Core 2 Quad 9550

    Ram :
    Corsair Dominator 4GB (2 x 2 GB) DDR2 1066 (PC2 8500) Twin2x4096-8500C5DF

    Power Supply : SeaSonic M12II-500Bronze(SS-500GM Active PFC)

    Video Card: Manli Nvidia GeForce 9800 (512MB
    DDR3)

    Sound Card: Internal

    Cooling System: Corsair H50

    Hard Drives: WD Green SATA2-(750GB)

  5. #15
    Join Date
    Nov 2009
    Location
    Jakarta
    Posts
    16

    Default Re: Need Help Setting Bios for GA-EP45-UD3LR And Q9550

    OK I will try them tonight
    CPU Reference ----------- 0.805V ------ : up to 0.785V

    MCH Reference ----------- 0.760V ------ : up to 0.740V

    The Problem remain the same as above

    CPU Reference ----------- 0.805V ------ : up to 0.785V

    MCH Reference ----------- 0.760V ------ : up to 0.762V

    And the computer went nuts, it's keep rebooting, and when i've finally in the bios setting again, it mention about no compatible overclocking setting
    Components:

    Motherboard : GA-EP45-UD3LR: Rev#:1.0

    BIOS Version : F7

    CPU : Intel Core 2 Quad 9550

    Ram :
    Corsair Dominator 4GB (2 x 2 GB) DDR2 1066 (PC2 8500) Twin2x4096-8500C5DF

    Power Supply : SeaSonic M12II-500Bronze(SS-500GM Active PFC)

    Video Card: Manli Nvidia GeForce 9800 (512MB
    DDR3)

    Sound Card: Internal

    Cooling System: Corsair H50

    Hard Drives: WD Green SATA2-(750GB)

  6. #16
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    849

    Default Re: Need Help Setting Bios for GA-EP45-UD3LR And Q9550

    OK I will try them tonight
    CPU Reference ----------- 0.805V ------ : up to 0.785V

    MCH Reference ----------- 0.760V ------ : up to 0.740V

    The Problem remain the same as above

    CPU Reference ----------- 0.805V ------ : up to 0.785V

    MCH Reference ----------- 0.760V ------ : up to 0.762V

    And the computer went nuts, it's keep rebooting, and when i've finally in the bios setting again, it mention about no compatible overclocking setting

    <!-- / message --><!-- sig -->
    This makes no sense to me if your default CPU Reference is .805 and you raise it one or two notches how can it be .785? Same with MCH Reference a default of .760 up to .740.

    Do this if you want, load optimized defaults, ( yeah I know you already have) reboot and input your dram voltage, reboot go into windows. Run Intel Burn Test and post your results...along with temps...

  7. #17
    Join Date
    Nov 2009
    Location
    Jakarta
    Posts
    16

    Default Re: Need Help Setting Bios for GA-EP45-UD3LR And Q9550

    OK i tried your suggestion, here is the result
    Components:

    Motherboard : GA-EP45-UD3LR: Rev#:1.0

    BIOS Version : F7

    CPU : Intel Core 2 Quad 9550

    Ram :
    Corsair Dominator 4GB (2 x 2 GB) DDR2 1066 (PC2 8500) Twin2x4096-8500C5DF

    Power Supply : SeaSonic M12II-500Bronze(SS-500GM Active PFC)

    Video Card: Manli Nvidia GeForce 9800 (512MB
    DDR3)

    Sound Card: Internal

    Cooling System: Corsair H50

    Hard Drives: WD Green SATA2-(750GB)

  8. #18
    Join Date
    Nov 2009
    Location
    Jakarta
    Posts
    16

    Default Re: Need Help Setting Bios for GA-EP45-UD3LR And Q9550

    next 1
    Components:

    Motherboard : GA-EP45-UD3LR: Rev#:1.0

    BIOS Version : F7

    CPU : Intel Core 2 Quad 9550

    Ram :
    Corsair Dominator 4GB (2 x 2 GB) DDR2 1066 (PC2 8500) Twin2x4096-8500C5DF

    Power Supply : SeaSonic M12II-500Bronze(SS-500GM Active PFC)

    Video Card: Manli Nvidia GeForce 9800 (512MB
    DDR3)

    Sound Card: Internal

    Cooling System: Corsair H50

    Hard Drives: WD Green SATA2-(750GB)

  9. #19
    Join Date
    Nov 2009
    Location
    Jakarta
    Posts
    16

    Default Re: Need Help Setting Bios for GA-EP45-UD3LR And Q9550

    Screen shot about setting bios after reseted to optimized setting

    the only change i've made only for the DRAM Voltagge
    Components:

    Motherboard : GA-EP45-UD3LR: Rev#:1.0

    BIOS Version : F7

    CPU : Intel Core 2 Quad 9550

    Ram :
    Corsair Dominator 4GB (2 x 2 GB) DDR2 1066 (PC2 8500) Twin2x4096-8500C5DF

    Power Supply : SeaSonic M12II-500Bronze(SS-500GM Active PFC)

    Video Card: Manli Nvidia GeForce 9800 (512MB
    DDR3)

    Sound Card: Internal

    Cooling System: Corsair H50

    Hard Drives: WD Green SATA2-(750GB)

  10. #20
    Join Date
    Nov 2009
    Location
    Jakarta
    Posts
    16

    Default Re: Need Help Setting Bios for GA-EP45-UD3LR And Q9550

    Log File while doing intel burn test
    Components:

    Motherboard : GA-EP45-UD3LR: Rev#:1.0

    BIOS Version : F7

    CPU : Intel Core 2 Quad 9550

    Ram :
    Corsair Dominator 4GB (2 x 2 GB) DDR2 1066 (PC2 8500) Twin2x4096-8500C5DF

    Power Supply : SeaSonic M12II-500Bronze(SS-500GM Active PFC)

    Video Card: Manli Nvidia GeForce 9800 (512MB
    DDR3)

    Sound Card: Internal

    Cooling System: Corsair H50

    Hard Drives: WD Green SATA2-(750GB)

Page 2 of 3 FirstFirst 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •