Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 4 of 38 FirstFirst ... 2345614 ... LastLast
Results 31 to 40 of 378

Thread: GA-X58A-UD7 - * Official Thread *




  1. #31
    Join Date
    Apr 2009
    Posts
    17

    Default Re: GA-X58A-UD7 - *Non-Official Thread*

    Quote Originally Posted by k1llah3rtz View Post
    @nyeah: please take and post picture of inside of your rig... plus.. does it does it boot with failsafe or optimized defaults in place?.. have you removed the board from the case and ran on a bench....???
    i don't even have a chance to mess with the BIOS, always run it in a case, never outside.
    when i load fail safe defaults/ load optimized default then save and exits, the problem will occur, not booting no post code, just the power led and ram led.

    i have tried replacing RAM, VGA, CPU cooler (with and without backplate, because noctua backplate doesn't seem to fit so i tried it)

    I haven't try replacing PSU though because i don't have spare.

    from where you want to see the system? i'll take a picture.

  2. #32
    Join Date
    Nov 2009
    Location
    Somewhere
    Posts
    300

    Default Re: GA-X58A-UD7 - *Non-Official Thread*

    the top.. so we can see that you've got the 8pin cpu power connected :D
    GA-X58A-UD7 rev1.0 - F9d // Intel i7 920 D0 @ 4.2Ghz - //vcore:Normal(1.2430v)+DVID+0.07500v//qpi_vtt:1.380v//bclk:200*21(turbo)
    6GB Corsair Dominator 1866 @ 1600 (9-9-9-24-2T@1.65v)


    CPU-Z Results: http://valid.canardpc.com/show_oc.php?id=2212669



  3. #33
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-X58A-UD7 - *Non-Official Thread*

    When you received the board back, did you look at the CPU socket pins to be sure NONE were bent? If not, please do so now, and be careful!

    Do you have an Intel stock cooler, if so test with that because your cooler may be causing a short you are not noticing, this especially worries me since you say the backplate does not fit.

    If you try the stock cooler and have no luck, and have checked and have NO Bent or missing CPU socket pins, then you are going to have to get the board out of your case and test it on a wooden table or box. When you do so please also remove if from the motherboard tray as well.

    Then test with one stick of memory in slot 1 white (2 physical). You do have the memory in the correct slots right now that I mention this I thought I should ask. They must go in the white slots (1,3,5)

    What memory is it anyway, just checking to be sure it is meant for X58

  4. #34
    Join Date
    Apr 2009
    Posts
    17

    Default Re: GA-X58A-UD7 - *Non-Official Thread*

    Quote Originally Posted by k1llah3rtz View Post
    the top.. so we can see that you've got the 8pin cpu power connected :D
    i'm 100% sure it's properly connected

  5. #35
    Join Date
    Nov 2009
    Location
    Somewhere
    Posts
    300

    Default Re: GA-X58A-UD7 - *Non-Official Thread*

    then as per above.. you need to very that you're not shorting out on anything..
    GA-X58A-UD7 rev1.0 - F9d // Intel i7 920 D0 @ 4.2Ghz - //vcore:Normal(1.2430v)+DVID+0.07500v//qpi_vtt:1.380v//bclk:200*21(turbo)
    6GB Corsair Dominator 1866 @ 1600 (9-9-9-24-2T@1.65v)


    CPU-Z Results: http://valid.canardpc.com/show_oc.php?id=2212669



  6. #36
    Join Date
    Apr 2009
    Posts
    17

    Default Re: GA-X58A-UD7 - *Non-Official Thread*

    hello all,

    i've found the problem, i swap the PSU and the problem is gone!

    is this hardware compatibility or my PSU is faulty.

  7. #37
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-X58A-UD7 - *Non-Official Thread*

    Only you can find out, test that PSU with another system or short it out and see if it even starts. Or test it with a PSU tester.

    What PSU is it anyway, in case it is a compatibility issue it would be great to know so we can warn others.

  8. #38
    Join Date
    Apr 2009
    Posts
    17

    Default Re: GA-X58A-UD7 - *Non-Official Thread*

    Quote Originally Posted by Lsdmeasap View Post
    Only you can find out, test that PSU with another system or short it out and see if it even starts. Or test it with a PSU tester.

    What PSU is it anyway, in case it is a compatibility issue it would be great to know so we can warn others.
    i'm using enermax revo 1050W, anyone here using same PSU?

    later i will try it on other system and report here, but i don't how to short it out though

    Thanks for lsdmeasap ada k1llah3rts for helping
    Last edited by nyeah; 12-12-2009 at 09:39 AM.

  9. #39
    Join Date
    May 2009
    Posts
    22

    Default Re: GA-X58A-UD7 - *Non-Official Thread*

    So finally got my new PC.

    i7 920, UD7.

    Ran occt linpak on stock cooler and it went over 80 degs in 12 mins.

    seems like thats not a good start.

    I have my noctua NH12p on now, and idles at about 39-40 degs and maxes at 67, all this on stock AUTO voltages.

    Ill have a play with it for now and see how i go, might have to start a help me thread later.

    EDIT- so ive ended up with 19x200 3.8Ghz for now, occt powersupply test for 1 hour, after using some of the bios suggestions on the site. 1.25 vcore, llc=2. Mux core temp 76deg ,HT on.

    I found it very hard to go past this freq, im guessing it will require some more qpi/vtt voltage adjustments. Ill make sure im stable at these setting and probably start my own tread. My CPU seems to run very hot in the board compared to some of the ones I have built this year using UD3R's, maybe just a cruddy cpu :(

    Config in Signature
    Last edited by BaldMan; 12-12-2009 at 11:18 PM.

  10. #40
    Join Date
    Jul 2009
    Posts
    7

    Default Re: GA-X58A-UD7 - *Non-Official Thread*

    Quote Originally Posted by nyeah View Post
    i'm using enermax revo 1050W, anyone here using same PSU?

    later i will try it on other system and report here, but i don't how to short it out though

    Thanks for lsdmeasap ada k1llah3rts for helping
    i'm using an enermax revo 1250 watt ... works well ...
    Last edited by abangcupi; 12-13-2009 at 03:52 PM.

Page 4 of 38 FirstFirst ... 2345614 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •