Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 30

Thread: +200 BCLK GA-X58 ud5




  1. #11
    Join Date
    Dec 2009
    Location
    Spain
    Posts
    16

    Default Re: +200 BCLK GA-X58 ud5

    Hi again.
    With this config. two minits with Prime 95 and system failure, but better than other configs.

    Updated Bios to f9k
    21X199
    DRAM Frec. 1592 (x8)
    Uncore x17
    x36
    CPU Vcore 1.32
    QPI/VTT 1.380
    PCIE 1.50
    QPI PLL 1.2
    IOH Core 1.22
    ICH Core 1.14
    DRAM Volt. 1.66
    9-10-10-25

    Help please.
    Last edited by miguelone; 12-08-2009 at 05:37 PM.

  2. #12
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: +200 BCLK GA-X58 ud5

    Please give me your full settings and specs in a template from my signature, then I can help.

  3. #13
    Join Date
    Dec 2009
    Location
    Spain
    Posts
    16

    Default Re: +200 BCLK GA-X58 ud5

    Hi again.

    Advanced CPU Features:
    CPU Clock Ratio ................................ [20x] 21
    Intel(R) Turbo Boost Tech .................. [Enabled]
    CPU Cores Enabled ............................ [All]
    CPU Multi Threading .......................... [Enabled] Disabled
    CPU Enhanced Halt (C1E) ................... [Disabled]
    C3/C6/C7 State Support .................... [Disabled]
    CPU Thermal Monitor ......................... [Enabled]
    CPU EIST Function ............................ [Disabled]
    Virtualization Technology ................... [Enabled]
    Bi-Directional PROCHOT ..................... [Enabled]


    Uncore & QPI Features:
    QPI Link Speed .............................. x36
    Uncore Frequency .......................... (Always 2x memory Multi or 2x +1) x17
    Isonchronous Frequency ..................[Enabled]


    Standard Clock Control:
    Base Clock (BCLK) Control ................ [Enabled]
    BCLK Frequency (MHz) .....................199
    PCI Express Frequency (MHz) ........... [100]

    C.I.A.2 [Disabled]

    Advanced Clock Control:
    CPU Clock Drive ..............................[800mV]
    PCI Express Clock Drive ................... [900mV]
    CPU Clock Skew ............................. [0ps]
    IOH Clock Skew ............................. [0ps]


    Advanced DRAM Features:
    Performance Enhance ...................... [Standard] Expert
    Extreme Memory Profile (X.M.P) ......... [Disabled]
    System Memory Multiplier (SPD) ........ [AUTO] x8
    DRAM Timing Selectable (SPD) .......... [Manual]

    Channel A + B + C

    Channel A Timing Settings:
    ##Channel A Standard Timing Control##
    CAS Latency Time ......................9
    tRCD .......................................10
    tRP .........................................10
    tRAS .......................................25

    Below values may be left in Auto if you like, generally this is fine. For those users who DO Set advanced timings manually, please see some of my thoughts and findings about these settings and rules here
    XtremeSystems Forums - View Single Post - Gigabyte EX58-UD5/Extreme Discussion Thread

    ##Channel A Advanced Timing Control##
    tRC ........................................ (Should be = tRAS + tRP or above for stability)
    tRRD .......................................
    tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
    tWR ........................................
    tWTP ....................................... (tWTP Must = tWR + tWL + 4)
    tWL ........................................ (tWL Must be CAS Latency -1)
    tRFC .......................................
    tRTP .......................................
    tFAW ......................................
    Command Rate (CMD) ................

    ##Channel A Misc Timing Control##
    Round Trip Latency ...................



    Advanced Voltage Control:

    CPU
    Load Line Calibration ................. [Disabled]
    CPU Vcore ...............................1.33
    QPI/VTT Voltage 1.150v ............ 1.380
    CPU PLL 1.800v ....................... 1.84

    MCH/ICH
    PCIE 1.500v ........................... 1.500
    QPI PLL 1.100v ....................... 1.2
    IOH Core 1.100v ..................... 1.22
    ICH I/O 1.500v ....................... 1.500
    ICH Core 1.1v ........................ 1.14

    DRAM 1592
    DRAM Voltage 1.500v .............. 1.66
    DRAM Termination 0.750v [AUTO]
    Ch-A Data VRef. 0.750v [AUTO]
    Ch-B Data VRef. 0.750v [AUTO]
    Ch-C Data VRef. 0.750v [AUTO]
    Ch-A Address VRef. 0.750v [AUTO]
    Ch-B Address VRef. 0.750v [AUTO]
    Ch-C Address VRef. 0.750v [AUTO]
    Thanks.

    Note: with prime95, system freeze, but not restart.(no bsod)
    Last edited by miguelone; 12-09-2009 at 05:46 AM.

  4. #14
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: +200 BCLK GA-X58 ud5

    Thanks, try these


    I do need a link to your memory though or the model # before I can best advise you

    Advanced CPU Features:
    CPU Clock Ratio ................................ [20x] 21
    Intel(R) Turbo Boost Tech .................. [Enabled]
    CPU Cores Enabled ............................ [All]
    CPU Multi Threading .......................... [Enabled] Disabled
    CPU Enhanced Halt (C1E) ................... [Disabled]
    C3/C6/C7 State Support .................... [Disabled]
    CPU Thermal Monitor ......................... [Enabled]
    CPU EIST Function ............................ [Disabled]
    Virtualization Technology ................... [Enabled]
    Bi-Directional PROCHOT ..................... [Enabled]


    Uncore & QPI Features:
    QPI Link Speed .............................. x36
    Uncore Frequency .......................... (Always 2x memory Multi or 2x +1) x17 << Try x18, some CPU's do not like Odd values here
    Isonchronous Frequency ..................[Enabled]


    Standard Clock Control:
    Base Clock (BCLK) Control ................ [Enabled]
    BCLK Frequency (MHz) .....................199
    PCI Express Frequency (MHz) ........... [100]

    C.I.A.2 [Disabled]

    Advanced Clock Control:
    CPU Clock Drive ..............................[800mV]
    PCI Express Clock Drive ................... [900mV]
    CPU Clock Skew ............................. [0ps]
    IOH Clock Skew ............................. [0ps]


    Advanced DRAM Features:
    Performance Enhance ...................... [Standard] Expert
    Extreme Memory Profile (X.M.P) ......... [Disabled]
    System Memory Multiplier (SPD) ........ [AUTO] x8
    DRAM Timing Selectable (SPD) .......... [Manual]

    Channel A + B + C

    Channel A Timing Settings:
    ##Channel A Standard Timing Control##
    CAS Latency Time ......................9
    tRCD .......................................10
    tRP .........................................10
    tRAS .......................................25

    Below values may be left in Auto if you like, generally this is fine. For those users who DO Set advanced timings manually, please see some of my thoughts and findings about these settings and rules here
    XtremeSystems Forums - View Single Post - Gigabyte EX58-UD5/Extreme Discussion Thread

    ##Channel A Advanced Timing Control##
    tRC ........................................ (Should be = tRAS + tRP or above for stability)
    tRRD .......................................
    tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
    tWR ........................................
    tWTP ....................................... (tWTP Must = tWR + tWL + 4)
    tWL ........................................ (tWL Must be CAS Latency -1)
    tRFC .......................................
    tRTP .......................................
    tFAW ......................................
    Command Rate (CMD) ................

    ##Channel A Misc Timing Control##
    Round Trip Latency ...................



    Advanced Voltage Control:

    CPU
    Load Line Calibration ................. [Disabled] << Enabled
    CPU Vcore ...............................1.33 << Try a bit more
    QPI/VTT Voltage 1.150v ............ 1.380 << May need 1.4-1.45+
    CPU PLL 1.800v ....................... 1.84

    MCH/ICH
    PCIE 1.500v ........................... 1.500
    QPI PLL 1.100v ....................... 1.2 << May need 1.24-1.3
    IOH Core 1.100v ..................... 1.22 << may need 1.24+
    ICH I/O 1.500v ....................... 1.500
    ICH Core 1.1v ........................ 1.14

    DRAM 1592
    DRAM Voltage 1.500v .............. 1.66
    DRAM Termination 0.750v [AUTO]
    Ch-A Data VRef. 0.750v [AUTO]
    Ch-B Data VRef. 0.750v [AUTO]
    Ch-C Data VRef. 0.750v [AUTO]
    Ch-A Address VRef. 0.750v [AUTO]
    Ch-B Address VRef. 0.750v [AUTO]
    Ch-C Address VRef. 0.750v [AUTO]

    Please do get me a link to your memory, as I doubt you need to use loose timings like you are now. 9-10-10-25 should not be needed at all, I assume you have them set like this for testing or to try and get things going, but you should not need to.

  5. #15
    Join Date
    Dec 2009
    Location
    Spain
    Posts
    16

    Default Re: +200 BCLK GA-X58 ud5

    Hi again

    my bios settings

    Advanced CPU Features:
    CPU Clock Ratio ................................ [20x] 21
    Intel(R) Turbo Boost Tech .................. [Enabled]
    CPU Cores Enabled ............................ [All]
    CPU Multi Threading .......................... [Enabled] Disabled
    CPU Enhanced Halt (C1E) ................... [Disabled]
    C3/C6/C7 State Support .................... [Disabled]
    CPU Thermal Monitor ......................... [Enabled]
    CPU EIST Function ............................ [Disabled]
    Virtualization Technology ................... [Enabled]
    Bi-Directional PROCHOT ..................... [Enabled]


    Uncore & QPI Features:
    QPI Link Speed .............................. x36
    Uncore Frequency .......................... (Always 2x memory Multi or 2x +1) 7 << Try x18, some CPU's do not like Odd values here x18
    Isonchronous Frequency ..................[Enabled]


    Standard Clock Control:
    Base Clock (BCLK) Control ................ [Enabled]
    BCLK Frequency (MHz) .....................199
    PCI Express Frequency (MHz) ........... [100]

    C.I.A.2 [Disabled]

    Advanced Clock Control:
    CPU Clock Drive ..............................[800mV]
    PCI Express Clock Drive ................... [900mV]
    CPU Clock Skew ............................. [0ps]
    IOH Clock Skew ............................. [0ps]


    Advanced DRAM Features:
    Performance Enhance ...................... [Standard] Expert
    Extreme Memory Profile (X.M.P) ......... [Disabled]
    System Memory Multiplier (SPD) ........ [AUTO] x8
    DRAM Timing Selectable (SPD) .......... [Manual]

    Channel A + B + C

    Channel A Timing Settings:
    ##Channel A Standard Timing Control##
    CAS Latency Time ......................9
    tRCD .......................................10
    tRP .........................................10
    tRAS .......................................25

    Below values may be left in Auto if you like, generally this is fine. For those users who DO Set advanced timings manually, please see some of my thoughts and findings about these settings and rules here
    XtremeSystems Forums - View Single Post - Gigabyte EX58-UD5/Extreme Discussion Thread

    ##Channel A Advanced Timing Control##
    tRC ........................................ (Should be = tRAS + tRP or above for stability)
    tRRD .......................................
    tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
    tWR ........................................
    tWTP ....................................... (tWTP Must = tWR + tWL + 4)
    tWL ........................................ (tWL Must be CAS Latency -1)
    tRFC .......................................
    tRTP .......................................
    tFAW ......................................
    Command Rate (CMD) ................

    ##Channel A Misc Timing Control##
    Round Trip Latency ...................



    Advanced Voltage Control:

    CPU
    Load Line Calibration ................. [Disabled] << Enabled
    CPU Vcore ...............................1.33 << Try a bit more 1.376(cpu-z)
    QPI/VTT Voltage 1.150v ............ 1.380 << May need 1.4-1.45+ 1.42
    CPU PLL 1.800v ....................... 1.84

    MCH/ICH
    PCIE 1.500v ........................... 1.500
    QPI PLL 1.100v ....................... 1.2 << May need 1.24-1.3 1.3
    IOH Core 1.100v ..................... 1.22 << may need 1.24+ 1.26
    ICH I/O 1.500v ....................... 1.500 1.5
    ICH Core 1.1v ........................ 1.14 1.16

    DRAM 1592
    DRAM Voltage 1.500v .............. 1.66
    DRAM Termination 0.750v [AUTO]
    Ch-A Data VRef. 0.750v [AUTO]
    Ch-B Data VRef. 0.750v [AUTO]
    Ch-C Data VRef. 0.750v [AUTO]
    Ch-A Address VRef. 0.750v [AUTO]
    Ch-B Address VRef. 0.750v [AUTO]
    Ch-C Address VRef. 0.750v [AUTO]


    My ram are Mushkin radioactive 12800 7-8-7-20 cl7

    They are on 9-10-10-25 to try first the cpu OC.

    No way with this configuration and with anyone, grrrrrrrrrrrrrrrrrrrrrrrrrr


    Help, please.

    Thanks.

  6. #16
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: +200 BCLK GA-X58 ud5

    What Model Mushkins? They do have the same timings as mine though, so they are likely 998679 just with the radioactive heatsink is all.

    You can see my signature for several sets of settings for this kit, same kit you have.

    You should be able to switch your ram timings right to 787-20 with the above settings, did you try yet?

  7. #17
    Join Date
    Dec 2009
    Location
    Spain
    Posts
    16

    Default Re: +200 BCLK GA-X58 ud5

    Hi.
    Mine are 998679r, and i think are the sames than yours.
    I have used your CL7 signature configuration, and system failure with prime95 in only three seconds.
    I dont know what to do . I will try another setthings, but i think i can be at the cpu oc limit.

    Thanks.

  8. #18
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: +200 BCLK GA-X58 ud5

    Yeap, same ones then just the different heatsink is all.

    Ok, well CL7, did you meant 787-20? Prime failing that fast is normally Vcore, but in this case could also be QPI/Vtt. Did you memtest86+ first? I always do a few quick runs with test 2/5/7 before I decide if the memory is stable enough for any other testing.

    What was your full settings you are now trying and I will advise back

  9. #19
    Join Date
    Dec 2009
    Location
    Spain
    Posts
    16

    Default Re: +200 BCLK GA-X58 ud5

    Hi again, and thanks for your time.

    I have passed memtest+86 to my ram, and one round passed without error.
    Here is my bios. Please, see all setting if something is wrong.

    ImageShack -

    See you.

  10. #20
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: +200 BCLK GA-X58 ud5

    You need to run 5-10 full passes of Memtest, or several rounds of 2/5/7

    Please use a template next time, that is a lot of images to look at and it is very hard to advise back to you that way

    Use Expert not quick, and set each channel one by one to the same values. If you are using x64 OS you need to change HPET setting to x64

    You did not show any voltage images? Anyway, please use a template next time if you don't mind, thanks!

Page 2 of 3 FirstFirst 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •