Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 6 of 6

Thread: EP45T-UD3P and e8400 constant blue screens




  1. #1
    Join Date
    Oct 2009
    Location
    Dallas
    Posts
    5

    Default EP45T-UD3P and e8400 constant blue screens

    I had my computer running well before using a past template I found here, but I accidentally reset to defaults and i can't find that old template anymore. I think I should have posted my info anyways to get settings more specific to my setup. At this point, I dont really care too much about OCing. I just want the computer running atm.

    CPU = e8400
    Motherboard = ep45t-UD3P Rev. 1.0
    BIOS Version = F7
    Ram = Patriot Viper 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Dual Channel Kit Desktop Memory Model PVS34G1600LLK timings : 7-7-7-20 1.9V

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 9x
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 3.00
     
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [disabled] 
    CPU Host Frequency (Mhz) ............: 333Mhz
    PCI Express Frequency (Mhz) .........:auto
    C.I.A.2 .................................:[Disabled]
     
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 0
    MCH Clock Skew (ps)...................: <<< 0
     
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 2.66D
    Memory Frequency (Mhz) ..............: 1066 889
    DRAM Timing Selectable ................: [Manual]
    Standard Timing Control
    CAS Latency Time........................ 7
    tRCD ......................................... 7
    tRP'...........................................7
    tRAS..........................................20
    Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
    Advanced Timing Control
    tRRD...........................................4 auto
    tWTR..........................................4 auto
    tWR............................................8 auto
    tRFC...........................................60 auto
    tRTP...........................................4 auto
    Command Rate (CMD) ....................:0  auto
    Driving Strength Profiles
    Driving Strength ............................
    Channel A
    Static tRead Value.........................:9
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    Channel B
    Static tRead Value.........................:9
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    Motherboard Voltage Control
    CPU
    CPU Vcore….……….........................:1.33125
    CPU Termination…..... 1.200V*.......: << auto
    CPU PLL…………………....1.500V*.......: << auto
    CPU Referen.…………....0.760V*.......: <<< auto
    CPU Reference2………,,0.760V*.......:<<< auto
    MCH/ICH
    MCH Core…………….....1.100V...........: << auto
    MCH Reference….…….0.760V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.500V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave
    DRAM
    DRAM Voltage ……....1.800V............: 1.700
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    Integrated Peripherals
    Legacy USB Storage Detect ..............[enabled] *Note* Must be enabled to flash from USB
    These settings were taken off of some other posts... but the ram was different than my ram.... Please help me get my system running stable again... let me know if i need to post any more information...

    Thanks
    E8400
    GA-EP45T-UD3P
    Patriot Viper 4GB (2 x 2GB) DDR3 1600 PVS34G1600LLK
    eVGA 9800GTX
    ZALMAN CNPS9500 AT

  2. #2
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: EP45T-UD3P and e8400 constant blue screens

    Please fill the template with your default values as well.
    A screen capture of MemSet main(click >>) and SPD(click spd) windows would be helpful, you can download it from http://forums.tweaktown.com/f69/late...30/#post284762
    Try increasing MCH Core graduately up to 1.24v.
    Memory is running at much lower frequency than it's spec. Try 4.00B or 3.20B memory multipliers.
    For these multiplier you need to set DRAM Voltage as specified by the manufacturer.

  3. #3
    Join Date
    Oct 2009
    Location
    Dallas
    Posts
    5

    Default Re: EP45T-UD3P and e8400 constant blue screens

    Sorry about that here are default values as well.
    The default values are right in front of "auto"...

    I also made a few changes...
    CPU host---400Mhz
    memory multiplier---3.2B
    MCHCore----1.18
    DRAM voltage---1.9v

    I can't get it to run at all on 4.0B.. probably because I'm such a newb at OCing.... thanks for any help...

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 9x
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 3.00
     
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [disabled] 
    CPU Host Frequency (Mhz) ............: 400Mhz
    PCI Express Frequency (Mhz) .........:auto
    C.I.A.2 .................................:[Disabled]
     
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 0
    MCH Clock Skew (ps)...................: <<< 0
     
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 3.2D
    Memory Frequency (Mhz) ..............: 1066 1280
    DRAM Timing Selectable ................: [Manual]
    Standard Timing Control
    CAS Latency Time........................ 7
    tRCD ......................................... 7
    tRP'...........................................7
    tRAS..........................................20
    Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
    Advanced Timing Control
    tRRD...........................................4 auto
    tWTR..........................................4 auto
    tWR............................................8 auto
    tRFC...........................................60 auto
    tRTP...........................................4 auto
    Command Rate (CMD) ....................:0  auto
    Driving Strength Profiles
    Driving Strength ............................
    Channel A
    Static tRead Value.........................:9
     tRD Phase0 Adjustment...................:  0  Auto 
    tRD Phase1 Adjustment...................:   0  Auto  
     tRD Phase2 Adjustment .................:   0  Auto  
     tRD Phase3 Adjustment..................:   0  Auto  
    Trd2rd(Different Rank)....................: 9  Auto  
    Twr2wr(Different Rank)...................:  7  Auto   
    Twr2rd(Different Rank)...................:  7  Auto   
    Trd2wr(Same/Diff Rank)..................:   10 Auto    
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    Channel B
    Static tRead Value.........................:9
     tRD Phase0 Adjustment...................:  0  Auto 
    tRD Phase1 Adjustment...................:   0  Auto  
     tRD Phase2 Adjustment .................:   0  Auto  
     tRD Phase3 Adjustment..................:   0  Auto  
    Trd2rd(Different Rank)....................: 9  Auto  
    Twr2wr(Different Rank)...................:  7  Auto   
    Twr2rd(Different Rank)...................:  7  Auto   
    Trd2wr(Same/Diff Rank)..................:   10 Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    Motherboard Voltage Control
    CPU
    CPU Vcore….……….........................:1.33125
    CPU Termination…..... 1.200V*.......: << 1.200v auto
    CPU PLL…………………....1.500V*.......: << 1.500v  auto
    CPU Referen.…………....0.760V*.......: <<< .760v  auto
    CPU Reference2………,,0.750V*.......:<<< .750v   auto
    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.18v  auto
    MCH Reference….…….0.760V...........; <<< .760v  Leave
    MCH/DRAM Ref.…......0.900V...........: <<< .750v Leave
    ICH I/O……………….....1.500V............: <<< 1.500v Leave
    ICH Core…………...……1.100V............: <<< 1.100v  Leave
    DRAM
    DRAM Voltage ……....1.800V............: 1.900 v
    DRAM Termination .…0.900V............: <<< .750v  Leave
    Channel A Reference 0.900V............: <<< .750v Leave
    Channel B Reference 0.900V............: <<< .750v Leave
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    Integrated Peripherals
    Legacy USB Storage Detect ..............[enabled] *Note* Must be enabled to flash from USB
    E8400
    GA-EP45T-UD3P
    Patriot Viper 4GB (2 x 2GB) DDR3 1600 PVS34G1600LLK
    eVGA 9800GTX
    ZALMAN CNPS9500 AT

  4. #4
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: EP45T-UD3P and e8400 constant blue screens

    Timings in the template don't match MemSet screen, are they auto?

    You have PVS34G1333LLK as memory part number in your sig, but MemSet SPD shows "1600LL Series" and it has XMP 800 profile (DDR-1600).

    Set Static tRead Value 10-12 for both channels, lower it later when you manage to get things stable.
    You have 3.33D multiplier, you can try that, and more MCH Core up to 1.24/1.26v.

    You said you don't care about OCing, plans have changed? what CPU cooler do you have?

    Please list value or auto, which ever applies, nex time you post settings, and remove the "leave"s.
    Default values to the left of the colons, auto or manually set values to the right.
    Reference voltages and DRAM Termination should be left on auto unless you need to change them.
    Vcore, CPU PLL, CPU Termination need not to be left on auto when OCing, see this post.

  5. #5
    Join Date
    Oct 2009
    Location
    Dallas
    Posts
    5

    Default Re: EP45T-UD3P and e8400 constant blue screens

    Sorry about the hassle chike... thanks for being patient with me...
    hopefully the third time is the charm...
    I think I put down the wrong memory for my sig as the 1600LL is the memory that I have.
    I ended up finishing the video that I needed to edit on another computer, so yes plans have changed, I want to try to get this thing moderately OCed...
    I have a Zalman CNPS9500AT cpu fan... I have not had trouble with overheating on my old motherboard... even when overclocked...
    This is the same as the last setup, just cleaned up. The memset shot is the same as the last post.

    Code:
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 0
    MCH Clock Skew (ps)...................: <<< 0
     
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 3.2D
    Memory Frequency (Mhz) ..............: 1066 1280
    DRAM Timing Selectable ................: [Manual]
    Standard Timing Control
    CAS Latency Time........................ 7 : auto
    tRCD ......................................... 7 : auto
    tRP'...........................................7 : auto
    tRAS..........................................20 : auto
    Set all Suggested below to highest Values first.  Then later you can lower, one at a time, 
    
    testing as you go
    Advanced Timing Control
    tRRD...........................................4 auto
    tWTR..........................................4 auto
    tWR............................................8 auto
    tRFC...........................................60 auto
    tRTP...........................................4 auto
    Command Rate (CMD) ....................:0  auto
    Driving Strength Profiles
    Driving Strength ............................
    Channel A
    Static tRead Value.........................:9
     tRD Phase0 Adjustment...................0 : Auto 
    tRD Phase1 Adjustment...................0 : Auto  
     tRD Phase2 Adjustment .................0 :  Auto  
     tRD Phase3 Adjustment..................0 : Auto  
    Trd2rd(Different Rank)....................9 : Auto  
    Twr2wr(Different Rank)...................7 : Auto   
    Twr2rd(Different Rank)...................7 : Auto   
    Trd2wr(Same/Diff Rank)..................10 :Auto    
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    Channel B
    Static tRead Value.........................:9
     tRD Phase0 Adjustment...................0 : Auto 
    tRD Phase1 Adjustment...................0 : Auto  
     tRD Phase2 Adjustment .................0 :  Auto  
     tRD Phase3 Adjustment..................0 : Auto  
    Trd2rd(Different Rank)....................9 : Auto  
    Twr2wr(Different Rank)...................7 : Auto   
    Twr2rd(Different Rank)...................7 : Auto   
    Trd2wr(Same/Diff Rank)..................10 :Auto    
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    Motherboard Voltage Control
    CPU
    CPU Vcore….……….........................:1.33125
    CPU Termination…..... 1.200V.......: << auto
    CPU PLL…………………....1.500V.......: <<  auto
    CPU Referen.…………....0.760V.......: <<<  auto
    CPU Reference2………,,0.750V.......:<<<   auto
    MCH/ICH
    MCH Core……………..............1.100V  : << 1.18v  
    MCH Reference….……..........0.760V  : <<< auto
    MCH/DRAM Ref.….............0.750V  : <<< auto
    ICH I/O………………...............1.500V : <<< auto
    ICH Core…………...……............1.100V: <<< auto
    DRAM
    DRAM Voltage …….....................: 1.900 v
    DRAM Termination .…..........0.750V  : <<<  auto
    Channel A Reference .........0.750V  : <<<  auto
    Channel B Reference .........0.750V  : <<<  auto
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    Integrated Peripherals
    Legacy USB Storage Detect ..............[enabled] *Note* Must be enabled to flash from USB
    E8400
    GA-EP45T-UD3P
    Patriot Viper 4GB (2 x 2GB) DDR3 1600 PVS34G1600LLK
    eVGA 9800GTX
    ZALMAN CNPS9500 AT

  6. #6
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: EP45T-UD3P and e8400 constant blue screens

    Quote Originally Posted by yohannus View Post
    hopefully the third time is the charm...
    Almost, the settings above Advanced Clock Control, no worries, just remember for next time.
    MemSet screen, especially the SPD window only needed once.
    Set CPU Termination 1.2v manually, increase it if needed.
    Set PLL 1.5v or one tick higher.

    Have you ran any stress tests yet?

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •