Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 13 FirstFirst 123412 ... LastLast
Results 11 to 20 of 129

Thread: Normal Voltage for E6750




  1. #11
    Ken429 is offline Senior Member
    Join Date
    Aug 2009
    Location
    Valapariso, Indiana
    Posts
    516

    Default Re: Normal Voltage for E6750

    ProJim, Back to the Q9550 system - I backed it off the FSB to 450 and lowered the Vcore to 1.34375V (LLC Disabled) and ran Prime95 for 6 hours. The voltage that OCCT showed using the above settings was 1.31V at idle and 1.26-1.28 under load. I then Enabled CIE, EIST, and Virtualization and walked away thinking all was ok. After this E6750 discussion I went back and ran OCCT on the Q9550 with the Enabled C1E and EIST settings and it now shows the system is at 1.07V when idle and at 1.20-1.22 under load. Does the 1.20-1.22V make sense, the Vcore is still at 1.34375V? The system seems stable but I have not run Prime95 - I think I'm afraid to??!!

  2. #12
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Normal Voltage for E6750

    I'm not sure why you're afraid to stress your system using Prime95.
    The worst that will happen is that your system will crash and "burn".
    You might get some file corruption when this happens, but it's really a non-issue if you have a backup image of your boot partition where you can quickly and easily restore the boot partition.
    I went back and ran OCCT on the Q9550 with the Enabled C1E and EIST settings and it now shows the system is at 1.07V when idle and at 1.20-1.22 under load.
    It's not clear which OCCT test you ran and for how long. Were you running any other monitoring programs that display voltages and the cpu load for all cores?
    Windows Task Manager (Performance tab) will show you how heavily loaded each core is during the test.

    With LLC, EIST, and C1E disabled, your cpu voltages have the expected vdroop of about 0.06 volts.
    With EIST and C1E enabled and with a consistent 100% load, your cpu voltage should be similar to your results with EIST and C1E disabled.

    I suggest testing your Q9550 by running a quick 10 loop test using Intel BurnTest (IBT) or LinX using the maximum amount of available memory. Either of these tests will result in cpu core temperatures that will be 10+ degrees higher than when running Prime95 or OCCT stress tests.
    I have never run either of these for longer than 20 loops.

    Another excellent test is to run OCCT PSU test, which stresses your cpu and graphics card at the same time. Even though OCCT can display and save graphs of voltages and temperatures, I run cpu-z and RealTemp while I'm testing my system.

    If you're anal (like me) when it comes to stress testing, I run each of the three Prime95 or OCCT tests for 24 hours each when I've reached my "final" overclock.
    I cheat a bit and only run multiple 12 hour stress tests when I'm in the process of seeking my overclocking goals.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  3. #13
    Ken429 is offline Senior Member
    Join Date
    Aug 2009
    Location
    Valapariso, Indiana
    Posts
    516

    Default Re: Normal Voltage for E6750

    The "afraid to run Prime95" was my sad attempt at humor since I new it would fail. Prime95 ran for less than 1 hour before W7 rebooted. I'm really confused now since the system was stable with C1E and EIST Disabled. I then increased the Vcore from the 1.34375V to 1.36250V and now OCCT and CPUz64 say the cpu voltage at idle is 1.30-1.33V and 1.28-1.30V under load. That is with C1E and EIST Enabled. It's like the BIOS has had a mood change. What am I missing?

  4. #14
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Normal Voltage for E6750

    Your Q9550 obviously isn't stable with EIST and C1E enabled.
    Which stability tests have you run and for how long with both of these options disabled?

    It would be best if you created a new thread where we can take a look/see at what might be causing the problem.
    I suggest a title with something like:
    Q9550 + EP45-UD3P overclock not stable with EIST & C1E enabled
    so that others will we drawn to the new thread.

    The best bet will be to post your failed bios settings and include a screen-shot that includes:
    Memset using the SPD and ">>" tabs
    cpu-z CPU and Mainboard screens (several instances can be run at the same time)
    EasyTune6 --> TUNER tab --> ADVANCE tab --> VOLTAGE tab (only the Voltage tab is needed)
    CoreTemp screen [for your cpu's VID (Voltage ID)]

    Be sure to detail which tests failed, error messages and how long the test ran. It would help if you include the failed Prime95/OCCT or IBT windows that generate errors.

    The problem might solved with some minor voltage tweaks and/or reference volt changes.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  5. #15
    Ken429 is offline Senior Member
    Join Date
    Aug 2009
    Location
    Valapariso, Indiana
    Posts
    516

    Default Re: Normal Voltage for E6750

    You're right. I will start a separate thread. I don't know if it is sun spots or what but I rebooted and the voltages are back to "normal". Honest, I did not change anything. Back to the E6750 discussion!

  6. #16
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Normal Voltage for E6750

    Must be good karma on your part ;)

  7. #17
    Ken429 is offline Senior Member
    Join Date
    Aug 2009
    Location
    Valapariso, Indiana
    Posts
    516

    Default Re: Normal Voltage for E6750

    ProJim,
    NewEgg did there usual fine job and I have the EP45-UD3P (rev. 1.6 BIOS Ver. FD) up and running. That's the good news. The bad news is it don't hunt any better than the old abit IP35 Pro MB! I suspect that the 4 sticks of Corsair Twin2X2048-6400C4 memory is the bottleneck. I have not tried to find the exact limit but somewhere after 430 things go bad. The memory is very stable at 400 with the 4-4-4-12 settings. The RamGuy at Corsair questioned the memory running at that speed with 4 sticks. Any suggestions? I know, go buy another 2X2048 sticks of the Mushkin 1066 memory?!

    Normal Voltage for E6750-e6750-430-jpg
    Last edited by Ken429; 03-04-2010 at 07:01 PM.

  8. #18
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Normal Voltage for E6750

    Did you load optimized bios settings before making any bios changes with your new motherboard?
    Your screen-shot shows some useful information, but it's best if you post your current bios settings together with the screen-shot.
    It helps if you click on the Memset "SPD" tab when you post your screen-shot.

    It looks like you're running with Performance Enhance = Standard, but Memset shows Performance Level = 0, which means that you left Static tRead Value (tRD) = AUTO.

    Which System Memory Multiplier are you using? 2.00B? 2.00D?
    With 4x1GB of Cas4 memory, you should be able to run:
    4-4-4-12 primary memory timings
    tRD = 8 when using 2.00B or tRD = 9 with 2.00D.
    Cpu Termination (VTT) = 1.26 might be needed.
    Set tRFC = AUTO until we can see your memory's SPD.

    I think that your current memory is fine and is probably good for 1000 and possibly 1066 speeds.
    You can buy another set of Mushkin 1066 Blackline memory, but there's a good chance that you're unnecessarily spending ~ $100 that you probably don't need. I'd stay with the Corsairs for the time being.

    Post your current bios settings along with the SPD window and we can better help you.
    Please detail the nature of your system's problems. BSOD? freezing? failed stress test?
    Which tests are failing and how long did they run?
    Provide details and/or screen-shots of the failed tests.
    More later....
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  9. #19
    Ken429 is offline Senior Member
    Join Date
    Aug 2009
    Location
    Valapariso, Indiana
    Posts
    516

    Default Re: Normal Voltage for E6750

    Here is all the good information you asked for, I Hope. The system runs ok (OCCT 60 Minutes with no errors). However, like on the abit MB as soon as I go much beyond 800 bad things happen. The screen snapshot shows the settings at FSB 425 and the Core0 error from OCCT after 21 minutes. Hopefully you can tell me where I've gone wrong with the BIOS settings.

    Code:
    Motherboard: Model: GA-EP45-UD3P(rev 1.6) Bios Version:  FD
    Cpu: E6750
    Ram: 4X1GB Brand:  Corsair Twin2048-C6400C4
    Power Supply Unit: Corsair 620HX
    
    
    MB Intelligent Tweaker (M.I.T.)
    Robust Graphics Booster ---------------- : [Auto] 
    CPU Clock Ratio ------------------------ : [ 8 X]
    CPU Frequency -----------------------: 3.40GHz( 425X8)
    
    Clock Chip Control
    
    Standard Clock Control
    CPU Host Clock Control ----------------- : [Enabled]
    CPU Host Frequency (Mhz) --------------- : [ 425]
    PCI Express Frequency (Mhz) ------------ : [100]
    C.I.A.2 -------------------------------- : [Disabled]
    
    Advanced Clock Control     [Press Enter]
    
    CPU Clock Drive ------------------------ : [ 800mV]
    PCI Express Clock Drive ---------------- : [ 900Mv]
    CPU Clock Skew (ps) -------------------- : [   0ps]
    MCH Clock Skew (ps) -------------------- : [   0ps]
    
    DRAM Performance Control
    Performance Enhance -------------------- : [Standard]
    (G)MCH Frequency Latch ----------------- : [Auto]
    System Memory Multiplier --------------- : [2.00D]
    Memory Frequency (Mhz) -----------------: 800 850
    DRAM Timing Selectable -(SPD)----------- : [Manual]
    
    Standard Timing Control
    CAS Latency Time -------- 5 ------------ : [4]		
    tRCD -------------------- 5 ------------ : [   4]	
    tRP --------------------- 5 ------------ : [   4]	
    tRAS ------------------- 18 ------------ : [  12]	
    
    Advanced Timing Control    [Press Enter]
    tRRD -------------------- 3 ------------ : [Auto]		
    tWTR -------------------- 3 ------------ : [Auto]		
    tWR --------------------- 6 -------------: [Auto]		
    tRFC ------------------- 42 ------------ : [Auto]		
    tRTP -------------------- 3 ------------ : [Auto]		
    Command Rate (CMD) ------ 0 -------------: [Auto]
    
    Channel A
    Channel A Timing Settings  [Press Enter]
    Static tRead Value ----- 10 ----------- : [ 9]		
    tRD Phase0 Adjustment --- 0 ------------ : [Auto]
    tRD Phase1 Adjustment --- 0 ------------ : [Auto]
    tRD Phase2 Adjustment --- 0 ------------ : [Auto]
    tRD Phase3 Adjustment --- 0 ------------ : [Auto]
    
    Trd2rd(Different Rank) -- 6 ------------ : [Auto]
    Twr2wr(Different Rank) -- 6 ------------ : [Auto]
    Twr2rd(Different Rank) -- 5 ------------ : [Auto]
    Trd2wr(Same/Diff Rank) -- 8 ------------ : [Auto]
    
    Dimm1 Clock Skew Control --------------- : [Auto]
    Dimm2 Clock Skew Control --------------- : [Auto]
    DDR Write Training --------------------- : [Auto]
    
    Channel B
    Channel B Timing Settings  [Press Enter]
    Static tRead Value ----- 10 ------------ : [ 9]		
    tRD Phase0 Adjustment --- 0 ------------ : [Auto]
    tRD Phase1 Adjustment --- 0 ------------ : [Auto]
    tRD Phase2 Adjustment --- 0 ------------ : [Auto]
    tRD Phase3 Adjustment --- 0 ------------ : [Auto]
    
    Trd2rd(Different Rank) -- 6 ------------ : [Auto]
    Twr2wr(Different Rank) -- 6 ------------ : [Auto]
    Twr2rd(Different Rank) -- 5 ------------ : [Auto]
    Trd2wr(Same/Diff Rank) -- 8 ------------ : [Auto]
    
    Dimm1 Clock Skew Control --------------- : [Auto]
    Dimm2 Clock Skew Control --------------- : [Auto]
    DDR Write Training --------------------- : [Auto]
    
    Channel A Driving Settings [Press Enter]
    Driving Strength Profile --------------- : [Auto]
    Data Driving Pull-Up Level ------------- : [Auto]
    Cmd  Driving Pull-Up Level ------------- : [Auto]
    Ctrl Driving Pull-Up Level ------------- : [Auto]
    Clk  Driving Pull-Up Level ------------- : [Auto]
    
    Data Driving Pull-Down Level ----------- : [Auto]
    Cmd  Driving Pull-Down Level ----------- : [Auto]
    Ctrl Driving Pull-Down Level ----------- : [Auto]
    Clk  Driving Pull-Down Level ----------- : [Auto]
    
    Channel B Driving Settings [Press Enter]
    Driving Strength Profile --------------- : [Auto]
    Data Driving Pull-Up Level ------------- : [Auto]
    Cmd  Driving Pull-Up Level ------------- : [Auto]
    Ctrl Driving Pull-Up Level ------------- : [Auto]
    Clk  Driving Pull-Up Level ------------- : [Auto]
    
    Data Driving Pull-Down Level ----------- : [Auto]
    Cmd  Driving Pull-Down Level ----------- : [Auto]
    Ctrl Driving Pull-Down Level ----------- : [Auto]
    Clk  Driving Pull-Down Level ----------- : [Auto]
    
    Motherboard Voltage Control
    CPU
    Voltage Types ----------- Normal ---------- Current
    Load-Line Calibration ------------------ : [Disabled]
    CPU Vcore --------------- 1.35000V ----- : [1.36875V] 
    
    CPU Termination --------- 1.200V* ------ : [1.260V] 
    CPU PLL ----------------- 1.500V* ------ : [1.570V] 
    CPU Reference ----------- 0.760V* ------ : [0.798V] 
    
    MCH/ICH
    MCH Core ---------------- 1.100V ------- : [1.260V] 
    MCH Reference ----------- 0.760V ------- : [0.798V]
    MCH/DRAM Ref ------------ 0.900V ------- : [1.000V]
    ICH I/O ----------------- 1.500V ------- : [1.500V] 
    ICH Core ---------------- 1.100V ------- : [1.200V] 
    DRAM
    DRAM Voltage ------------ 1.800V ------- : [2.100V] 
    DRAM Termination -------- 0.900V ------- : [1.000V]
    Channel A Reference ----- 0.900V ------- : [Auto]
    Channel B Reference ----- 0.900V ------- : [Auto]
    
    Standard CMOS Features
    Floppy A ------------------------------- : [None]
    Floppy 3 Mode Support ------------------ : [Disabled]
    
    Advanced Settings
    Hard Disk Boot Priority ---------------- : [Press Enter]
    Quick Boot ----------------------------- : [Disabled]
    First Boot Device ---------------------- : [CDROM]
    Second Boot Device --------------------- : [CDROM]
    Third Boot Device ---------------------- : [Hard Disk]
    Boot Up Floppy Seek -------------------- : [Disabled]
    Boot up Num-Lock ----------------------- : [On]
    Password Check ------------------------- : [Setup]
    HDD S.M.A.R.T. Capability -------------- : [Enabled]
    CPU Multi-Threading -------------------- : [Enabled]
    Limit CPUID Max. to 3 ------------------ : [Disabled]
    No-Execute Memory Protect -------------- : [Disabled]
    CPU Enhanced Halt (C1E) ---------------- : [Disabled]
    CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
    CPU EIST Function ---------------------- : [Disabled]
    Virtualization Technology -------------- : [Disabled] 
    Display For HDD (Secs) ----------------- : [ 0]
    Full Screen LOGO Show ------------------ : [Disabled]
    Backup BIOS Image to HDD --------------- : [Disabled]
    Init Display First --------------------- : [PEG]
    
    Integrated Peripherals
    SATA RAID/AHCI Mode -------------------- : [Disabled]
    SATA Port0-3 Native Mode --------------- : [Disabled]
    Azalia Codec --------------------------- : [Auto]
    Onboard H/W 1394 ----------------------- : [Disabled]
    Onboard H/W LAN1 ----------------------- : [Enabled]
    Onboard H/W LAN2 ----------------------- : [Enabled]
    Green Lan ------------------------------ : [Disabled]
    Smart LAN1 ----------------------------- : [Press Enter]
    Smart LAN2 ----------------------------- : [Press Enter]
    Onboard LAN1 Boot ROM ------------------ : [Disabled]
    Onboard LAN2 Boot ROM ------------------ : [Disabled]
    Onboard SATA/IDE Device ---------------- : [Enabled]
    Onboard SATA/IDE Ctrl Mode ------------- : [IDE]
    Onboard Serial Port 1 ------------------ : [Disabled]
    Onboard Parallel Port ------------------ : [Disabled]
    X Parallel Port Mode ------------------- :  SPP
    X ECP Mode Use DMA --------------------- :  3
    USB 1.0 Controlller -------------------- : [Enabled]
    USB 2.0 Controlller -------------------- : [Enabled]
    USB Keyboard Function ------------------ : [Enabled]
    USB Mouse Function --------------------- : [Enabled]
    USB Storage Function ------------------- : [Disabled]
    
    PC Health Status
    Reset Case Open Status ----------------- : [Disabled]
    CPU Warning Temperature ---------------- : [70 C/158 F]
    CPU Fan Warning ------------------------ : [Disabled]
    System Fan2 Fail Warning --------------- : [Disabled]
    Power Fan Warning ---------------------- : [Disabled]
    System Fan1 Fail Warning --------------- : [Disabled]
    CPU Smart Fan Control ------------------ : [Enabled]
    CPU Smart Fan Mode --------------------- : [PWM]
    Attached Images Attached Images Normal Voltage for E6750-e6750_425_fail-jpg 

  10. #20
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Normal Voltage for E6750

    Make one bios change at a time and re-run OCCT Medium Dataset until there are no OCCT errors.
    Stop performing tests if OCCT runs error free for at least 8 - 12 hours, longer is better.
    1. Set CPU Ref and MCH Ref = AUTO and retest. <--- this counts as 1 change
    2. Set Cpu Termination (VTT) = 1.28 (1 step higher) and retest.
    3. Set Dram Voltage = 2.12 and retest.
    4. Set tRFC = 48 and retest.
    5. Set VTT = 1.30 and re-test.
    6. Set System Memory Multiplier to 2.00B, set tRD = 8 for both memory channels (A & B) and retest..

    Note how long OCCT runs until the first error. After each test completes, go to the folder where the OCCT program is, probably in C:\Program Files\OCCT. You should find Thread1.txt and Thread2.txt files. Open each file and note the error code for each thread. You'll probably find the code is = 4 for the thread that failed and the other file will probably say "code: 1". The OCCT Help file explains the codes.

    Keep working down the change list and stop testing if OCCT runs error free for an extended stress test.

    Are we having any fun yet?

    **edit** In the Power Management Setup section, is HPET Support enabled and HPET Mode = 64-bit mode?
    Last edited by profJim; 03-05-2010 at 08:40 AM. Reason: 1 more question
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


Page 2 of 13 FirstFirst 123412 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •