Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 4 of 6 FirstFirst ... 23456 LastLast
Results 31 to 40 of 51

Thread: Buyers tip: Good OC Motherboard?




  1. #31
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Buyers tip: Good OC Motherboard?

    Hmm, I always need to see your full settings to best advise. Likely more Vcore or Vtt though

  2. #32

    Default Re: Buyers tip: Good OC Motherboard?

    Red is edited.

    Code:
    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [9]
    Fine Clock Ratio ____________[0]
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ [450]
    PCI Express Frequency (Mhz)_______ [102]
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [2.66D]
    DRAM Timing Selectable_______ SPD __ [Manual]
    
    Performance Enhance = [Standard]
    
    CAS Latency Time________________[9]
    Dram RAS# to CAS# Delay_________[9]
    Dram RAS# Precharge Delay_______[9]
    Precharge Delay (tRAS)__________[24]
    
    ACT to ACT Delay (tRRD)_________[auto](5)
    Rank Write to READ Delay________[auto](5)
    Write to Precharge Delay_________[auto](10)
    Refresh to ACT Delay______________[auto](74)
    Read to Precharge Delay__________[auto](5)
    Static tRead Value_______________[12]
    Static tRead Phase Adjust________ [Auto]
    CMD_____________________________[auto]
    
    CPU/PCIEX Clock Driving Control [800mV]
    CPU Clock Skew Control [normal]
    GMCH Clock Skew Control [Normal]
    
    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [+0.15V]
    PCI-E OverVoltage Control_ [+0.10V]
    FSB OverVoltage Control___ [+0.25V]
    (G)MCH OverVoltage Control [+0.30V]
    CPU Voltage Control_______ [1.475]
    Loadline calibration______[auto]
    
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Disabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]  dont have this
    x C4/C4E State Support..................: [Disabled]  dont have this
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]
    
    Integrated Peripherals
    Legacy USB Storage Detect___________________[enabled]
    Last edited by badpop; 03-28-2010 at 12:00 AM.
    GA-X58A-UD3R (2.0)
    Intel i7 930 (stock atm)
    Intel X25-M G2 80GB
    Corsair H50 Cpu cooler powered by a Noctua Fan
    *Corsair XMS3 DHX 9-9-9-24
    ASUS ENGTX480/2DI/1536MD5
    Corsair 750 HX
    Fractal Design Define R2 case
    2x 750GB Samsung F1 Spinpoint in raid 0

    HTPC (WIP):
    GA-X48T-DQ6 rev 1.3 BIOS F6E
    Intel C2D E8400 (stock atm)
    Velociraptor 160GB
    Gainward HD 4870
    Zalman HP600

    *Waiting for HTPC retirement

  3. #33
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Buyers tip: Good OC Motherboard?

    Try these changes
    Code:
    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [9]
    Fine Clock Ratio ____________[0]
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ [450]
    PCI Express Frequency (Mhz)_______ [102]  << Could also cause issues, see if 100 helps or not.
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [2.66D]
    DRAM Timing Selectable_______ SPD __ [Manual]
    
    Performance Enhance = [Standard]
    
    CAS Latency Time________________[9]
    Dram RAS# to CAS# Delay_________[9]
    Dram RAS# Precharge Delay_______[9]
    Precharge Delay (tRAS)__________[24]
    
    ACT to ACT Delay (tRRD)_________[auto](5)
    Rank Write to READ Delay________[auto](5)
    Write to Precharge Delay_________[auto](10)
    Refresh to ACT Delay______________[auto](74)
    Read to Precharge Delay__________[auto](5)
    Static tRead Value_______________[12]  << may be too high, try 9-10 for now
    Static tRead Phase Adjust________ [Auto]
    CMD_____________________________[auto]  << 2T for now
    
    CPU/PCIEX Clock Driving Control [800mV]
    CPU Clock Skew Control [normal]
    GMCH Clock Skew Control [Normal]
    
    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [+0.15V] << This enough for your memory?  = 1.65V or less, check PC health section or everest sensors to be sure what you are getting
    PCI-E OverVoltage Control_ [+0.10V]
    FSB OverVoltage Control___ [+0.25V]
    (G)MCH OverVoltage Control [+0.30V]
    CPU Voltage Control_______ [1.475]  << Less, once you enable LLC below you wont need so much voltage.   Of course lower then slowly, once you are sure LLC helped
    Loadline calibration______[auto] << Enabled
    
    
    No-Execute Memory Protect............: [Disabled] < Enable, this will not affect your overclock and should be enabled

  4. #34

    Default Re: Buyers tip: Good OC Motherboard?

    Applied your settings, ddr3 was at 1,68v according to PC health. Ill try orthos and see what happenes.
    GA-X58A-UD3R (2.0)
    Intel i7 930 (stock atm)
    Intel X25-M G2 80GB
    Corsair H50 Cpu cooler powered by a Noctua Fan
    *Corsair XMS3 DHX 9-9-9-24
    ASUS ENGTX480/2DI/1536MD5
    Corsair 750 HX
    Fractal Design Define R2 case
    2x 750GB Samsung F1 Spinpoint in raid 0

    HTPC (WIP):
    GA-X48T-DQ6 rev 1.3 BIOS F6E
    Intel C2D E8400 (stock atm)
    Velociraptor 160GB
    Gainward HD 4870
    Zalman HP600

    *Waiting for HTPC retirement

  5. #35
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

  6. #36

    Default Re: Buyers tip: Good OC Motherboard?

    seems very unstable.
    using tRead 10 and have been trying to balance the cpu voltage between 1,45-1,47 but I still get Bluescreen 124. When I upped the ddr3 voltage to +0,2v then I got 124 as soon as windows started.
    GA-X58A-UD3R (2.0)
    Intel i7 930 (stock atm)
    Intel X25-M G2 80GB
    Corsair H50 Cpu cooler powered by a Noctua Fan
    *Corsair XMS3 DHX 9-9-9-24
    ASUS ENGTX480/2DI/1536MD5
    Corsair 750 HX
    Fractal Design Define R2 case
    2x 750GB Samsung F1 Spinpoint in raid 0

    HTPC (WIP):
    GA-X48T-DQ6 rev 1.3 BIOS F6E
    Intel C2D E8400 (stock atm)
    Velociraptor 160GB
    Gainward HD 4870
    Zalman HP600

    *Waiting for HTPC retirement

  7. #37
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: Buyers tip: Good OC Motherboard?

    Do you have GTLREFs options? If not try to prees Ctrl+F1 and see if it reveal them.

  8. #38

    Default Re: Buyers tip: Good OC Motherboard?

    In bios?

    btw, hi again chike :)
    GA-X58A-UD3R (2.0)
    Intel i7 930 (stock atm)
    Intel X25-M G2 80GB
    Corsair H50 Cpu cooler powered by a Noctua Fan
    *Corsair XMS3 DHX 9-9-9-24
    ASUS ENGTX480/2DI/1536MD5
    Corsair 750 HX
    Fractal Design Define R2 case
    2x 750GB Samsung F1 Spinpoint in raid 0

    HTPC (WIP):
    GA-X48T-DQ6 rev 1.3 BIOS F6E
    Intel C2D E8400 (stock atm)
    Velociraptor 160GB
    Gainward HD 4870
    Zalman HP600

    *Waiting for HTPC retirement

  9. #39
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: Buyers tip: Good OC Motherboard?

    Yes Ctrl+F1 in main BIOS screen, the screen will flash once, then se if you have them in MIT.

  10. #40
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Buyers tip: Good OC Motherboard?

    CPU Voltage is not going to help with 124 errors, you need to increase Vtt (CPU Termination) voltages.

    Are you doing that, or Vcore? Please raise Vtt not vcore to correct 124 errors

Page 4 of 6 FirstFirst ... 23456 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •