Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 1 of 6 123 ... LastLast
Results 1 to 10 of 53

Thread: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everything




  1. #1
    Join Date
    Mar 2010
    Location
    United States
    Posts
    23

    Exclamation HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everything

    EP45 -UD3P BIOS VER. FD
    Intel QX6700
    4 X 2 CM2x2048-8500C5D
    NVIDIA GTX 260
    Soundblaster X-FI

    I have been experiencing .
    -unexpected_kernel_mode_trap
    -page_fault_in_nonpaged_area
    -memory_management
    -irql_not_less_or_equal
    -cache_manager
    -bad_pool_header

    These are my current bios settings below. I have ran memtest on all sticks 1 at a time. They all tested good. I just installed Windows 7 updated it to current then installed all updated drivers. After i change settings in bios it will run ok for a day then start acting up after that. I tryed just running two sticks of mem in channel B but no dice it did the same as when all 4 sticks are in. HELP!!
    Im at the end of my rope with this system its been one thing after another. HELP!!!!

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 10x
    CPU Frequency ...........................: 2.66 (266x10)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 266
    PCI Express Frequency (Mhz) .........: 100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 700Mv
    PCI Express Clock Drive.................: 700mV
    CPU Clock Skew (ps)....................: 0
    MCH Clock Skew (ps)...................: 0


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: [Disabled]
    (G)MCH Frequency Latch...............: [266 MHz]
    System Memory Multiplier ..............: 3.00A
    Memory Frequency (Mhz) ..............: 800
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................5
    tRCD .........................................5
    tRP'...........................................5
    tRAS..........................................15

    Advanced Timing Control
    tRRD...........................................4
    tWTR..........................................4
    tWR............................................8
    tRFC...........................................68
    tRTP...........................................4
    Command Rate (CMD) ....................:0 [AUTO]

    Channel A
    Static tRead Value.........................:Auto 7
    tRD Phase0 Adjustment...................:Auto 0
    tRD Phase1 Adjustment...................:Auto 0
    tRD Phase2 Adjustment .................:Auto 0
    tRD Phase3 Adjustment..................:Auto 0
    Trd2rd(Different Rank)....................: 6
    Twr2wr(Different Rank)...................: 6
    Twr2rd(Different Rank)...................: 5
    Trd2wr(Same/Diff Rank)..................: 8
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps
    DDR Write Training..........................:Auto

    Channel B
    Static tRead Value.........................:Auto 7
    tRD Phase0 Adjustment...................:Auto 0
    tRD Phase1 Adjustment...................:Auto 0
    tRD Phase2 Adjustment .................:Auto 0
    tRD Phase3 Adjustment..................:Auto 0
    Trd2rd(Different Rank)....................: 6
    Twr2wr(Different Rank)...................: 6
    Twr2rd(Different Rank)...................: 5
    Trd2wr(Same/Diff Rank)..................: 8
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps
    DDR Write Training..........................:Auto
    Motherboard Voltage Control

    CPU
    CPU Vcore….……….........................:Auto (1.33750)

    CPU Termination…..... 1.200V*.......: Auto (1.2)
    CPU PLL…………………....1.500V*.......: Auto (1.5)
    CPU Reference.…………....0.755V*.......: Auto (0.760)

    MCH/ICH
    MCH Core…………….....1.100V...........: 1.3
    MCH Reference….…….0.800V...........; Auto (0.760)
    MCH/DRAM Ref.…......0.900V...........: Auto (0.900)
    ICH I/O……………….....1.500V............: Auto (1.500)
    ICH Core…………...……1.100V............: Auto (1.100)

    DRAM
    DRAM Voltage ……....1.800V............: 2.200
    DRAM Termination .…0.900V............: Auto (0.900)
    Channel A Reference 0.900V............: Auto (0.900)
    Channel B Reference 0.900V............: Auto (0.900)

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]

    Integrated Peripherals
    USB Keyboard..................................[Enabled]
    USB Mouse......................................[Enabled]
    USB Storage....................................[Enabled]

  2. #2
    Join Date
    Mar 2010
    Location
    San Jose
    Posts
    35

    Default Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

    Just curious, why do you have to set the PCI Express Clock Drive to 700mV? You may want to set it back to 900mV

    Also, why do you have to set those settings? I suggest to leave it Auto for now.

    Trd2rd(Different Rank)....................: 6
    Twr2wr(Different Rank)...................: 6
    Twr2rd(Different Rank)...................: 5
    Trd2wr(Same/Diff Rank)..................: 8

    Also set Vcore, VTT, PLL, to the value on the left, don't set it on Auto. And is your DRAM Voltage manufacture recommended? If you're not overclocking, then set it to the manufactured voltage.

    Hope this help.
    Q6700 @3.48GHz [8x435MHz] VID 1.2875 Full Load IBT 77c Ambient 24c
    TRUE with Push Pull Scythe Slip Stream 120mm SY1225SL
    Tuniq TX-2 Cooling Thermal Compound
    GIGABYTE EP45-UD3P [rev: 1.0] ~ Bios: F10
    4 x 2GB G.Skill PC2 8000 @5-4-4-12 870MHz [2.00B]
    Antec 1200 + 4 Rosewill RFA-120-BL 120mm
    Sapphire 100259-1GL Radeon HD 4870 1GB
    Corsair CMPSU-750TX
    WD Caviar Black WD1001FALS 1TB 7200 RPM SATA 3.0
    Windows 7 64bit.
    Dell 2408 WFP
    HK-254 Receiver + 4x Energy C-100 + Energy C-C100 + Energy S10.3

  3. #3
    Join Date
    Mar 2010
    Location
    United States
    Posts
    23

    Default Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

    I had them set and it still crashed so i went back to auto.....

  4. #4
    Join Date
    Mar 2010
    Location
    San Jose
    Posts
    35

    Default Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

    How about the timings, PCI-E clock drive (900mV) and CPU clock drive (800mV)? You should set them back to default and auto.
    Q6700 @3.48GHz [8x435MHz] VID 1.2875 Full Load IBT 77c Ambient 24c
    TRUE with Push Pull Scythe Slip Stream 120mm SY1225SL
    Tuniq TX-2 Cooling Thermal Compound
    GIGABYTE EP45-UD3P [rev: 1.0] ~ Bios: F10
    4 x 2GB G.Skill PC2 8000 @5-4-4-12 870MHz [2.00B]
    Antec 1200 + 4 Rosewill RFA-120-BL 120mm
    Sapphire 100259-1GL Radeon HD 4870 1GB
    Corsair CMPSU-750TX
    WD Caviar Black WD1001FALS 1TB 7200 RPM SATA 3.0
    Windows 7 64bit.
    Dell 2408 WFP
    HK-254 Receiver + 4x Energy C-100 + Energy C-C100 + Energy S10.3

  5. #5
    Join Date
    Mar 2010
    Location
    United States
    Posts
    23

    Default Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

    Set them to 900MV and 800Mv. Ran prime 95 and it crashed again.

  6. #6
    Join Date
    Mar 2010
    Location
    San Jose
    Posts
    35

    Default Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

    Please post your updated BIOS settings again. How long did prime95 run? How long did you test your memory sticks? What was the crash message if it was a BSOD?
    Q6700 @3.48GHz [8x435MHz] VID 1.2875 Full Load IBT 77c Ambient 24c
    TRUE with Push Pull Scythe Slip Stream 120mm SY1225SL
    Tuniq TX-2 Cooling Thermal Compound
    GIGABYTE EP45-UD3P [rev: 1.0] ~ Bios: F10
    4 x 2GB G.Skill PC2 8000 @5-4-4-12 870MHz [2.00B]
    Antec 1200 + 4 Rosewill RFA-120-BL 120mm
    Sapphire 100259-1GL Radeon HD 4870 1GB
    Corsair CMPSU-750TX
    WD Caviar Black WD1001FALS 1TB 7200 RPM SATA 3.0
    Windows 7 64bit.
    Dell 2408 WFP
    HK-254 Receiver + 4x Energy C-100 + Energy C-C100 + Energy S10.3

  7. #7
    Join Date
    Mar 2010
    Location
    United States
    Posts
    23

    Default Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

    Prime ran till the 12k test then it crashed but in the logs it said it passed. It crashed on a Bug Check this time. I ran memtest on all sticks about 6 to 8 hours while i was sleeping. They all passed.

    I have been experiencing Also
    -unexpected_kernel_mode_trap
    -page_fault_in_nonpaged_area
    -memory_management
    -irql_not_less_or_equal
    -cache_manager
    -bad_pool_header


    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 10x
    CPU Frequency ...........................: 2.66 (266x10)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 266
    PCI Express Frequency (Mhz) .........: 100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800Mv
    PCI Express Clock Drive.................: 900mV
    CPU Clock Skew (ps)....................: 0
    MCH Clock Skew (ps)...................: 0


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: [Disabled]
    (G)MCH Frequency Latch...............: [266 MHz]
    System Memory Multiplier ..............: 3.00A
    Memory Frequency (Mhz) ..............: 800
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................5
    tRCD .........................................5
    tRP'...........................................5
    tRAS..........................................15

    Advanced Timing Control
    tRRD...........................................4
    tWTR..........................................4
    tWR............................................8
    tRFC...........................................68
    tRTP...........................................4
    Command Rate (CMD) ....................:0 [AUTO]

    Channel A
    Static tRead Value.........................:Auto
    tRD Phase0 Adjustment...................:Auto
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................: Auto
    Twr2wr(Different Rank)...................: Auto
    Twr2rd(Different Rank)...................: Auto
    Trd2wr(Same/Diff Rank)..................: Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps
    DDR Write Training..........................:Auto

    Channel B
    Static tRead Value.........................:Auto
    tRD Phase0 Adjustment...................:Auto
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................: Auto
    Twr2wr(Different Rank)...................: Auto
    Twr2rd(Different Rank)...................: Auto
    Trd2wr(Same/Diff Rank)..................: Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps
    DDR Write Training..........................:Auto
    Motherboard Voltage Control

    CPU
    CPU Vcore….……….........................:(1.33750)

    CPU Termination…..... 1.200V*.......: (1.2)
    CPU PLL…………………....1.500V*.......: (1.5)
    CPU Reference.…………....0.755V*.......: (0.760)

    MCH/ICH
    MCH Core…………….....1.100V...........: 1.3
    MCH Reference….…….0.800V...........; (0.760)
    MCH/DRAM Ref.…......0.900V...........: (0.900)
    ICH I/O……………….....1.500V............: (1.500)
    ICH Core…………...……1.100V............: (1.100)

    DRAM
    DRAM Voltage ……....1.800V............: 2.100
    DRAM Termination .…0.900V............: Auto (0.900)
    Channel A Reference 0.900V............: Auto (0.900)
    Channel B Reference 0.900V............: Auto (0.900)

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]

    Integrated Peripherals
    USB Keyboard..................................[Enabled]
    USB Mouse......................................[Enabled]
    USB Storage....................................[Enabled]

  8. #8
    Join Date
    Mar 2010
    Location
    San Jose
    Posts
    35

    Default Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

    If it crashes on 12k FFT test then mostly it's a CPU problem. But your other errors seem like a memory problem or a faulty board but I'm not quite sure.

    Last try:
    Code:
    (G)MCH Frequency Latch...............: [266 MHz] <--- set this Auto
    System Memory Multiplier ..............: 3.00A <--- set this 2.00B or 2.00D (try both to see if it works)
    tRRD...........................................4 <--- set this Auto
    tWTR..........................................4 <--- set this Auto
    tWR............................................8 <--- set this Auto
    tRFC...........................................68 <--- set this Auto
    tRTP...........................................4 <--- set this Auto
    CPU Termination…..... 1.200V*.......: (1.2) <--- try to increase it to 1.3V to see if it helps.
    No-Execute Memory Protect............: [Enabled] <--- Disable for now
    If this still doesn't work then I suggest you to wait for Lsdmeasap or someone more experienced than me to help you. I don't see why your settings won't work. Your CPU is not overclocked at all.
    Q6700 @3.48GHz [8x435MHz] VID 1.2875 Full Load IBT 77c Ambient 24c
    TRUE with Push Pull Scythe Slip Stream 120mm SY1225SL
    Tuniq TX-2 Cooling Thermal Compound
    GIGABYTE EP45-UD3P [rev: 1.0] ~ Bios: F10
    4 x 2GB G.Skill PC2 8000 @5-4-4-12 870MHz [2.00B]
    Antec 1200 + 4 Rosewill RFA-120-BL 120mm
    Sapphire 100259-1GL Radeon HD 4870 1GB
    Corsair CMPSU-750TX
    WD Caviar Black WD1001FALS 1TB 7200 RPM SATA 3.0
    Windows 7 64bit.
    Dell 2408 WFP
    HK-254 Receiver + 4x Energy C-100 + Energy C-C100 + Energy S10.3

  9. #9
    Join Date
    Mar 2010
    Location
    United States
    Posts
    23

    Default Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

    I will check those settings out. If you think of anything else let me know. I will let you know the results.

  10. #10
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

    Don't manually change the Clock Drive settings.
    700/700 are the default values when you load Fail-Safe settings. These should be named Failure-Prone settings!
    You want to load Optimized Bios settings before you make any bios changes. The optimized defaults change some hidden bios settings that are required for stable operation.

    You will make it much easier for us to help you if you provide the detailed information in steps 1 - 4 in this post.
    Please add your detailed hardware information, bios version, mobo version and a link to your memory in your forum signature and post the screen-shot in step 4.

    Set tRFC = 72 - 74 with 8GB of memory.
    MCH Core = 1.32 - 1.36 might be needed.
    CPU Termination = 1.22 - 1.26 should help.

    If these settings don't help, try testing with only 2x2GB of memory with MCH Core = 1.22 - 1.24 volts.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


Page 1 of 6 123 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •