These settings should get you going

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................:10
Fine CPU Clock Ratio.....................:+0.5
CPU Frequency ...........................: 2.8(266x10.5)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Disabled]
CPU Host Frequency (Mhz) ............:266 Mhz
PCI Express Frequency (Mhz) .........:auto << 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................:800
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0


DRAM Performance Control
Performance Enhance...................: [turbo] << Standard
Extreme Memory Profile (X.M.P.).....: I do not have this setting
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: auto << 3.00A
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [auto]

Standard Timing Control
CAS Latency Time........................6
tRCD .........................................6
tRP'...........................................6
tRAS..........................................18

Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

Advanced Timing Control
tRRD...........................................3-4
tWTR..........................................3-6
tWR............................................4-6
tRFC...........................................52-62
tRTP...........................................3-4
Command Rate (CMD) ....................:0 << Set 2T

Driving Strength Profiles
Driving Strength ............................800/1066 (1066 may work best, try first)

Channel A
Static tRead Value.........................:5 << For now set 7-8
tRD Phase0 Adjustment...................:Auto 0
tRD Phase1 Adjustment...................:Auto 0
tRD Phase2 Adjustment .................:Auto 1
tRD Phase3 Adjustment..................:Auto 1
Trd2rd(Different Rank)....................:Auto 6
Twr2wr(Different Rank)...................:Auto 6
Twr2rd(Different Rank)...................:Auto 5
Trd2wr(Same/Diff Rank)..................:Auto 8
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:5 << For now set 7-8
tRD Phase0 Adjustment...................:Auto 0
tRD Phase1 Adjustment...................:Auto 0
tRD Phase2 Adjustment .................:Auto 1
tRD Phase3 Adjustment..................:Auto 1
Trd2rd(Different Rank)....................:Auto 6
Twr2wr(Different Rank)...................:Auto 6
Twr2rd(Different Rank)...................:Auto 5
Trd2wr(Same/Diff Rank)..................:Auto 8
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control

CPU
CPU Vcore….……….1.2875............:Auto no over clocking

CPU Termination…..... 1.200V....: auto no over clocking
CPU PLL…………………....1.500V.......: I don't have a setting for that

CPU Referen.…………....0.805.......: auto


MCH/ICH
MCH Core…………….....1.100V...........:auto << Set 1.2-1.24 for 4GB
MCH Reference….…….0.760V...........; Don't see it
MCH/DRAM Ref.…......0.900V...........: Don't see it
ICH I/O……………….....1.550V............: auto
ICH Core…………...……1.100V............: Don't see it

DRAM
DRAM Voltage ……....1.800V............: Set manually 1.82-1.88, then after a reboot check PC Helth section of the BIOS to be sure you are getting at least 1.8V
DRAM Termination .…0.900V............: Don't see it
Channel A Reference 0.900V............: Don't see it
Channel B Reference 0.900V............: Don't see it

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Enabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Enabled]
Virtualization Technology................: [Enabled] No i don't have virtual PC, i don't even know whats that << Disabled then please