Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 30

Thread: Ga-890gpa-ud3h o/c




  1. #11
    Join Date
    Apr 2009
    Location
    Virginia
    Posts
    1,470

    Default Re: Ga-890gpa-ud3h o/c

    The pictures you got on voltages and timings are no help on auto for this system voltage control and timing items must be set to manual. Any voltages on auto wont show until they are set to manual and save and reboot. Then take the pictures so we can see the voltages and timing items.

    I would start with some temperature warnings in case it get's hot while you are not paying attention. Some simple changes in pc health should help. I will put them in red for you to change. If you here the warning beep you will want to shut down. Your cpu is rated at 70C max. Then turn off smart fan control which will allow the cpu fan to run at maximum speed all the time. This is until you have a chance to remedy the problem. This you may never need to do. Lets make these change only for now and boot up to your OS and let us know your findings before we make changes to memory timings.
    Code:
    PC Health Status
    Hardware Thermal Control [Enabled]
    Reset Case Open Status [Disabled]
    Case Opened No        yes
    Vcore 1.364V          1.472
    DDR3 1.5V 1.536V  1.488
    +3.3V 3.280V           3.344
    +12V 12.048V           12.175
    Current System Temperature 38oC     36
    Current CPU Temperature 36oC          28
    Current CPU FAN Speed 1962 RPM     1011
    Current SYSTEM FAN1 Speed 0 RPM
    Current SYSTEM FAN2 Speed 0 RPM
    Current POWER FAN Speed 0 RPM
    CPU Warning Temperature [70oC/158oF]
    CPU FAN Fail Warning [Disabled]
    SYSTEM FAN1 Fail Warning [Disabled]
    SYSTEM FAN2 Fail Warning [Disabled]
    POWER FAN Fail Warning [Disabled]
    CPU Smart FAN Control [Enabled]
    CPU Smart FAN Mode [Auto]
    System Smart FAN Control [Enabled]
    If you have a black edition cpu you will be able to change the cpu clock ratio. http://products.amd.com/en-us/Deskto...f11=&f12=&f13=
    You don't so we will be adjusting the cpu frequency which is a little more tricky. It will change the memory, northbridge, and HT Link frequencies at the same time. So we need to calibrate these settings as well. The best way is set the memory, northbridge, and HT Link multipliers down a little to adjust for the much higher overall frequency which they call cpu frequency. I will supply minor tweeks on voltage as well.
    Code:
    MB Intelligent Tweaker(M.I.T.)
    } IGX Configuration [Press Enter]
    CPU Clock Ratio [Auto] 2800Mhz     3200
    CPU NorthBridge Freq. [9X or 18x] 1800Mhz
    CPU Host Clock Control [Manual]
    x CPU Frequency(MHz) 240
    PCIE Clock(MHz) [Auto]
    HT Link Width [Auto]
    HT Link Frequency [Manual] 1800Mhz
    Set Memory Clock [manual]          
    x Memory Clock x6.66 1333Mhz           x6.66   1333Mhz
    } DRAM Configuration [Press Enter]
    ******** System Voltage Optimized ********
    System Voltage Control [Manual]
    x CPU PLL Voltage Control Auto
    x DRAM Voltage Control +0.15=1.65v
    x DDR VTT Voltage Control auto
    x NB Voltage Control auto
    x SidePort Mem Volt Control auto 
    x NB/PCIe/PLL Voltage Control auto
    x CPU NB VID Control auto
    x CPU Voltage Control Auto
    Normal CPU Vcore 1.3250V
    Oh yeah save changes press y and exit reboot into Windows
    Last edited by artdrivers; 04-04-2010 at 09:15 AM.
    http://forums.tweaktown.com/gigabyte...ench-test.html
    http://www.gigabyte-usa.com/FileList...ios_qflash.pdf
    Phenom II 945 @ 3.2Ghz w/Thermaltake Big Typhoon Pro 14 CPU Cooler
    Gigabyte GA-MA78GM-S2H rev.1.1 F11
    Sapphire 3870HD / 100225L / 512MB / ddr4
    4GB / Kingston / KHX8500D2K2/2GN / 5-5-5-18 / 1066Mhz
    (2) WD Caviar / WD2500AAKS/ 250GB in SATA RAID-0
    (1) WD Caviar / WD2500AAKS/ 250GB in SATA AHCI
    (2) IDE's 1 8XdualDVDRW 1 52x32x52x CDRW
    Antec /Neo HE550 / 550W
    Mid size ATX case with show through panel
    2) 80x80 front fans (1) 120x120 rear fan and small nb fan
    Microsoft comfort curve USB keyboard 2000 ver.1.0
    Logitech G500 USB mouse
    Monitor: CMV937A
    7.1+2 Channel High Definition ALC889A
    Dual boot Windows 7 32bit home & Windows 7 64bit home


  2. #12
    Join Date
    Dec 2008
    Posts
    88

  3. #13
    Join Date
    Dec 2008
    Posts
    88

  4. #14
    Join Date
    Apr 2009
    Location
    Virginia
    Posts
    1,470

    Default Re: Ga-890gpa-ud3h o/c

    Awesome OC but you may want to set Dram voltage control to 1.5v +.15 = 1.65V and set Row Cycle Time to 32T 8+8+8+24=32T. Then try Prime 95 torture test http://mersenneforum.org/gimps/p64v2511.zip
    See how long you can go without errors, but watch temperatures. I use HWmonitor for eyeing voltage and temperatures in Windows. http://www.cpuid.com/download/hwmoni...itor64_115.zip
    These and other programs can be found here.
    http://forums.tweaktown.com/f69/late...y-tools-30530/
    http://forums.tweaktown.com/gigabyte...ench-test.html
    http://www.gigabyte-usa.com/FileList...ios_qflash.pdf
    Phenom II 945 @ 3.2Ghz w/Thermaltake Big Typhoon Pro 14 CPU Cooler
    Gigabyte GA-MA78GM-S2H rev.1.1 F11
    Sapphire 3870HD / 100225L / 512MB / ddr4
    4GB / Kingston / KHX8500D2K2/2GN / 5-5-5-18 / 1066Mhz
    (2) WD Caviar / WD2500AAKS/ 250GB in SATA RAID-0
    (1) WD Caviar / WD2500AAKS/ 250GB in SATA AHCI
    (2) IDE's 1 8XdualDVDRW 1 52x32x52x CDRW
    Antec /Neo HE550 / 550W
    Mid size ATX case with show through panel
    2) 80x80 front fans (1) 120x120 rear fan and small nb fan
    Microsoft comfort curve USB keyboard 2000 ver.1.0
    Logitech G500 USB mouse
    Monitor: CMV937A
    7.1+2 Channel High Definition ALC889A
    Dual boot Windows 7 32bit home & Windows 7 64bit home


  5. #15
    Join Date
    Dec 2008
    Posts
    88

    Default Re: Ga-890gpa-ud3h o/c

    Will try your settings after work tonight. I ran OCCT for 2 hours and temp never went higher than 23c. How do I unlock ? Thanks

  6. #16
    Join Date
    Apr 2009
    Location
    Virginia
    Posts
    1,470

    Default Re: Ga-890gpa-ud3h o/c

    How do I unlock ?
    I am not sure the SB850 offers ACC.
    If your bios does not have (ACC) Advanced Clock Calibration then you can't.
    You may want to check your hidden bios feature by pressing CTRL+F1 on the main bios page or first page. Then navigate to MB Intelligent Tweaker(M.I.T.)
    Here is a bios image of the MB Intelligent Tweaker(M.I.T.) on a GA-MA790GPT-UD3H which has the SB750. It offers the (ACC)
    Code:
    MB Intelligent Tweaker(M.I.T.)
    } Advanced Clock Calibration [Press Enter]
    CPU Clock Ratio [Auto] 2800Mhz
    CPU NorthBridge Freq. [Auto] 2000Mhz
    CPU Host Clock Control [Auto]
    x CPU Frequency(MHz) 200
    PCIE Clock(MHz) [Auto]
    HT Link Width [Auto]
    HT Link Frequency [Auto] 2000Mhz
    VGA Core Clock control [Disabled]
    x VGA Core Clock(MHz) 700
    Set Memory Clock [Auto]
    x Memory Clock x6.66 1333Mhz
    } DRAM Configuration [Press Enter]
    ******** System Voltage Optimized ********
    System Voltage Control [Manual]
    DDR3 Voltage Control [Normal]
    NorthBridge Volt Control [Normal]
    SouthBridge Volt Control [Normal]
    SidePort Mem Volt Control [Normal]
    CPU NB VID Control [Normal]
    CPU Voltage Control [Normal]
    Normal CPU Vcore 1.3250V
    Just set the EC Firmware to Hybrid
    Code:
    Advanced Clock Calibration
    EC Firmware Selection [Hybridl]
    Advanced Clock Calibration [Enabled]
    x Value (All Cores) -2%
    x Value (Core 0) -2%
    x Value (Core 1) -2%
    x Value (Core 2) -2%
    x Value (Core 3) -2%
    EC Firmware Selection
    Allows you to select the EC firmware version when Advanced Clock Calibration is enabled. After the selection, select Save & Exit Setup in the BIOS Main Menu and then press <Y>. A message which says "BIOS Is Updating EC Firmware!!! Don't Turn Off Or Reset System" will appear. Wait for a few seconds and the system will automatically restart for the settings to take effect.
    Normal Uses the standard AMD EC firmware version. (Default)
    Hybrid Uses the specific AMD EC firmware version. Advanced Clock Calibration
    Allows you to determine whether to enable Advanced Clock Calibration when using an AMD Black Edition CPU.
    Disabled Disables this function. (Default)
    Auto Lets the BIOS to configure the settings to defaults.
    All Cores Configures Advanced Clock Calibration for all CPU cores.
    Per Core Individually configures Advanced Clock Calibration for each CPU core. Value (All Cores)
    This option is configurable only when Advanced Clock Calibration is set to All Cores.
    Options are: -12%~+12%. Value (Core 0), Value (Core 1), Value (Core 2), Value (Core 3)
    This option is configurable only when Advanced Clock Calibration is set to All Cores.
    Options are: -12%~+12%.
    MORE RESEARCH NEEDED
    OCWorkbench
    Last edited by artdrivers; 04-06-2010 at 08:15 AM.
    http://forums.tweaktown.com/gigabyte...ench-test.html
    http://www.gigabyte-usa.com/FileList...ios_qflash.pdf
    Phenom II 945 @ 3.2Ghz w/Thermaltake Big Typhoon Pro 14 CPU Cooler
    Gigabyte GA-MA78GM-S2H rev.1.1 F11
    Sapphire 3870HD / 100225L / 512MB / ddr4
    4GB / Kingston / KHX8500D2K2/2GN / 5-5-5-18 / 1066Mhz
    (2) WD Caviar / WD2500AAKS/ 250GB in SATA RAID-0
    (1) WD Caviar / WD2500AAKS/ 250GB in SATA AHCI
    (2) IDE's 1 8XdualDVDRW 1 52x32x52x CDRW
    Antec /Neo HE550 / 550W
    Mid size ATX case with show through panel
    2) 80x80 front fans (1) 120x120 rear fan and small nb fan
    Microsoft comfort curve USB keyboard 2000 ver.1.0
    Logitech G500 USB mouse
    Monitor: CMV937A
    7.1+2 Channel High Definition ALC889A
    Dual boot Windows 7 32bit home & Windows 7 64bit home


  7. #17
    Join Date
    Dec 2008
    Posts
    88

    Default Re: Ga-890gpa-ud3h o/c

    Quote Originally Posted by artdrivers View Post
    Awesome OC but you may want to set Dram voltage control to 1.5v +.15 = 1.65V and set Row Cycle Time to 32T 8+8+8+24=32T. Then try Prime 95 torture test http://mersenneforum.org/gimps/p64v2511.zip
    See how long you can go without errors, but watch temperatures. I use HWmonitor for eyeing voltage and temperatures in Windows. http://www.cpuid.com/download/hwmoni...itor64_115.zip
    These and other programs can be found here.
    http://forums.tweaktown.com/f69/late...y-tools-30530/
    Made your changes running prime at defaults (how Long) with HWmonitor...Ran for 8 hours with no errors
    Last edited by race301; 04-06-2010 at 06:32 PM.

  8. #18
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Ga-890gpa-ud3h o/c

    If you guys want I can look in the BIOS to see if ACC is there or not, if you need me to look in it please tell me which version and I can check for you and post images of the settings visible/invisible to users

  9. #19
    Join Date
    Dec 2008
    Posts
    88

    Default Re: Ga-890gpa-ud3h o/c

    Quote Originally Posted by Lsdmeasap View Post
    If you guys want I can look in the BIOS to see if ACC is there or not, if you need me to look in it please tell me which version and I can check for you and post images of the settings visible/invisible to users
    Thanks it is F5 03/18/2010

  10. #20
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Ga-890gpa-ud3h o/c

    Sorry, it is not in that BIOS at all. Not hidden either, just not in the BIOS period.

    You will need a different board, or to send in a ticket and see if you can get them to add to that BIOS. I am not sure, but I think only certain chipsets support that. Artdrivers will be able to tell you which, if your board/chipset is one of them you will need to get them to add it into the BIOS.

Page 2 of 3 FirstFirst 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •