Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 3 of 3 FirstFirst 123
Results 21 to 24 of 24

Thread: GA-EP45-UD3P - Q9550 not posting correctly...




  1. #21
    Join Date
    Apr 2010
    Location
    NJ
    Posts
    14

    Default Re: GA-EP45-UD3P - Q9550 not posting correctly...

    Is there a way I can copy and paste it over here? =) or I gotta use your as an outline.. but Ill do it!


    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto or Fast
    CPU Clock Ratio ..........................: 8
    Fine CPU Clock Ratio.....................:. .5
    CPU Frequency ...........................: 3.4


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 400Mhz
    PCI Express Frequency (Mhz) .........:Set to 100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<<
    MCH Clock Skew (ps)...................: <<<


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 2.40D
    Memory Frequency (Mhz) ..............: 900Mhz
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................ 5
    tRCD ......................................... 5
    tRP'........................................... 5
    tRAS.......................................... 15

    Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

    Advanced Timing Control
    tRRD........................................... 4
    tWTR.......................................... 6
    tWR............................................ 6
    tRFC........................................... 62
    tRTP........................................... 5
    Command Rate (CMD) ....................:2

    Driving Strength Profiles
    Driving Strength ............................ 1066

    Channel A
    Static tRead Value.........................: 10
    tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:10
    tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control

    CPU
    CPU Vcore….……….........................: auto

    CPU Termination…..... 1.200V*.......: << 1.24

    CPU PLL…………………....1.500V*.......: auto

    CPU Referen.…………....0.755V*.......: auto

    CPU Reference2………,,0.800V*.......: auto
    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.2
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.500V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave

    DRAM
    DRAM Voltage ……....1.800V............: 2.1
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
    a computer

  2. #22
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP45-UD3P - Q9550 not posting correctly...

    You didn't say, what speed do you want to try?

    I see you are using the .5 CPU multi, did you leave that enabled when you tried the settings I suggested before, if so that may be why they failed as I suggested to not use that and only use 8.

  3. #23
    Join Date
    Apr 2010
    Location
    NJ
    Posts
    14

    Default Re: GA-EP45-UD3P - Q9550 not posting correctly...

    i did just 8 last time when attempting to go 3.8... i did most of the settings but i didnt change voltage much... just vcore to 1.3 then it didnt boot and gave up.
    a computer

  4. #24
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP45-UD3P - Q9550 not posting correctly...

    Ahh ok. Well you need to try voltages, don't be scared set it higher then you think you might need just so you can get booting, you can lower it later.

    Try this for 3.6 again

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto or Fast
    CPU Clock Ratio ..........................: 8
    Fine CPU Clock Ratio.....................:. .0
    CPU Frequency ...........................: 3.6


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 450Mhz
    PCI Express Frequency (Mhz) .........:Set to 100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<<
    MCH Clock Skew (ps)...................: <<<


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 2.40D << there is no 2.40D? Set 2.00D for now, or try 2.00B
    Memory Frequency (Mhz) ..............: 900Mhz
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................ 5
    tRCD ......................................... 5
    tRP'........................................... 5
    tRAS.......................................... 15

    Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

    Advanced Timing Control
    tRRD........................................... 3
    tWTR.......................................... 4
    tWR............................................ 6
    tRFC........................................... 62
    tRTP........................................... 3
    Command Rate (CMD) ....................:2

    Driving Strength Profiles
    Driving Strength ............................ 1066

    Channel A
    Static tRead Value.........................: 10
    tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:10
    tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control

    CPU
    CPU Vcore….……….........................: 1.3-1.425

    CPU Termination…..... 1.200V*.......: << 1.26-1.32

    CPU PLL…………………....1.500V*.......: auto

    CPU Referen.…………....0.755V*.......: auto

    CPU Reference2………,,0.800V*.......: auto
    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.24
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.500V............: <<< 1.5
    ICH Core…………...……1.100V............: <<< 1.14

    DRAM
    DRAM Voltage ……....1.800V............: 2.1
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave

Page 3 of 3 FirstFirst 123

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •