Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 24

Thread: EX-58, ud4p, boot loops then freezes, repeat...




  1. #11
    Join Date
    Mar 2009
    Posts
    12

    Default Re: EX-58, ud4p, boot loops then freezes, repeat...

    Okay I installed in bios and here are my bios settings,


    Advanced CPU Features:
    CPU Clock Ratio ................................ [20x]
    Intel(R) Turbo Boost Tech .................. [Enabled]
    CPU Cores Enabled ............................ [All]
    CPU Multi Threading .......................... [Enabled]
    CPU Enhanced Halt (C1E) ................... [Enabled]
    C3/C6/C7 State Support .................... [Disabled]
    CPU Thermal Monitor ......................... [Enabled]
    CPU EIST Function ............................ [Enabled]
    Virtualization Technology ................... [Enabled] << Disabled if you do not use Vmware or Virtual PC Programs
    Bi-Directional PROCHOT ..................... [Enabled]


    Uncore & QPI Features:
    QPI Link Speed .............................. [auto]
    Uncore Frequency .......................... [auto]
    Isonchronous Frequency ..................[Enabled]


    Standard Clock Control:
    Base Clock (BCLK) Control ................ [Disable]
    BCLK Frequency (MHz) .....................[133]
    PCI Express Frequency (MHz) ........... [auto]

    C.I.A.2 [Disabled]

    Advanced Clock Control:
    CPU Clock Drive ..............................[700mV]
    PCI Express Clock Drive ................... [700mV]
    CPU Clock Skew ............................. [0ps]
    IOH Clock Skew ............................. [0ps]


    Advanced DRAM Features:
    Performance Enhance ...................... [Standard]
    Extreme Memory Profile (X.M.P) ......... [Disabled]
    System Memory Multiplier (SPD) ........ [AUTO]
    DRAM Timing Selectable (SPD) .......... [auto]

    Channel A + B + C

    Channel A Timing Settings:

    ##Channel A Standard Timing Control##
    CAS Latency Time ......................7 auto
    tRCD .......................................7 auto
    tRP .........................................7 auto
    tRAS .......................................20 auto

    On a different note my hd 4870 is having some trouble, when I plug it in and boot up I get an error message
    that says my card is not connected to power, I tried the my other two power connectors and got the same
    message.

  2. #12
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: EX-58, ud4p, boot loops then freezes, repeat...

    Please load optimized defaults, save/apply/reboot F10.

    Then give me your settings again.

    Are you wanting to run stock Bclk and memory speeds? If not tell me what you want to try and I will suggest settings.

    I also need the full template of settings, voltages, ect that you left out.

    About your 4870, are you sure your PSU is good enough? Load optimized as mentioned above and reboot and see if that helps or not

  3. #13
    Join Date
    Mar 2009
    Posts
    12

    Default Re: EX-58, ud4p, boot loops then freezes, repeat...

    Okay so you need all of my bios settings after I load optimized defaults. I plugged my video card and psu into a different pc and it booted up fine, the psu is 750w pc power and cooling so it should be fine. Ill post the other settings as soon as possible.

  4. #14
    Join Date
    Mar 2009
    Posts
    12

    Default Re: EX-58, ud4p, boot loops then freezes, repeat...

    Alrighty then,


    Advanced CPU Features
    CPU Clock Ration 20X
    Turbo boost Enabled
    CPU Cores Enable All
    CPU Multi-Threading Enabled
    CPU Enhanced Halt Enabled
    C3/C6/C7 State Support Disabled
    CPU Thermal Monitor Enabled
    CPU EIST Function Enabled
    Bi-Directional PROCHOT Enabled
    Virtualization Technology Enabled

    UnCore & QPI Features
    QPI Clock Ratio Auto
    QPI link speed 4.8ghz
    Uncore clock Ratio Auto
    Uncore Frequency 2667mhz
    Isochronous Support Enabled

    Advanced Clock Control
    Base Clock Control Disable
    BLCK Frequency 133
    PCI Express Frequency auto
    C.I.A.2 Disable

    CPU Clock Drive 800nV
    PCI Express Clock Drive 900nv
    CPU Clock skew 0ps
    IOH Clock skew 0ps

    Performance Enhance turbo
    System Memory Multiplier auto
    Memory frequency 1066
    DRAM Timing Selectable auto
    Profile DDR Voltage 1.5v
    Profile QPI Voltage 1.15v

    Channel A B & C

    CAS Latency Time 7 auto
    tRCD 7 auto
    tRP 7 auto
    tRAS 20 auto
    Command Rate 1 auto
    Advanced Voltage Control
    Load-Line Calibration Disabled
    cpu vcore 1.28750v auto
    Dynamic Vcore 0.00000v auto
    qpi/vtt voltage 1.150v auto
    cpu pll 1.800v auto
    mch/ich
    pcie 1.500v auto
    qpi pll 1.100v auto
    ioh core 1.100v auto
    ich i/o 1.500v auto
    ich core 1.100v auto
    dram
    dram voltage 1.500v auto
    dram termination 0.750v auto
    Ch-a data vref 0.750v auto
    Ch-b data vref 0.750v auto
    Ch-c data vref 0.750v auto
    Ch-a address vref 0.750v auto
    Ch-b address vref 0.750v auto
    Ch-c address vref 0.750v auto

    Do you need the rest like standard cmos features, and advanced bios features?
    And I would like to run it at 3.33 and 1333 memory again.
    Last edited by willem3de; 05-14-2010 at 05:00 AM.

  5. #15
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: EX-58, ud4p, boot loops then freezes, repeat...

    Thanks, I just needed the ones in the template in my signature.

    Well running 3.33Ghz puts you at a funny place for your memory, you will need either run 1280Mhz or 1600Mhz (Which this memory will do!)

    So I will give you settings for both ways

    BSOD Error codes and what they mean:
    0X00000050 << Incorrect Memory Timing/Freq or Uncore Multi
    0X00000124 << Incorrect QPI/Vtt Voltage (To Much/Not Enough)
    0X00000101 << Not enough Vcore Voltage


    Code:
    Advanced CPU Features:
    CPU Clock Ratio ................................ [20x]
    Intel(R) Turbo Boost Tech .................. [Enabled]  << Or disabled here and set 21 above
    CPU Cores Enabled ............................ [All]
    CPU Multi Threading .......................... [Enabled]
    CPU Enhanced Halt (C1E) ................... [Disabled]
    C3/C6/C7 State Support .................... [Disabled]
    CPU Thermal Monitor ......................... [Enabled]
    CPU EIST Function ............................ [Disabled]
    Virtualization Technology ................... [Enabled] << Disabled if you do not use Vmware or Virtual PC Programs
    Bi-Directional PROCHOT ..................... [Enabled]
    
    
    Uncore & QPI Features:
    QPI Link Speed .............................. x36 or x44 (Both are fine to use at 160 Bclk)
    Uncore Frequency ..........................  (Always 2x memory Multi or 2x +1, 2x +2, ect - Higher means more Vdimm or QPI/Vtt often but can help stability)  So if using x8 memory multi set this to 16-18, if using x10 memory multi set this to 20-22
    Isonchronous Frequency ..................[Enabled]
    
    
    Standard Clock Control:
    Base Clock (BCLK) Control ................ [Enabled]
    BCLK Frequency (MHz) ..................... 160  = 3.336Ghz
    PCI Express Frequency (MHz) ........... [100]
    
    C.I.A.2 [Disabled]
    
    Advanced Clock Control:
    CPU Clock Drive ..............................[800mV]
    PCI Express Clock Drive ................... [900mV]
    CPU Clock Skew ............................. [0ps]
    IOH Clock Skew ............................. [0ps]
    
    
    Advanced DRAM Features:
    Performance Enhance ...................... [Standard]  << Turbo or Extreme may be best to use here
    Extreme Memory Profile (X.M.P) ......... [Disabled]
    System Memory Multiplier (SPD) ........ [AUTO]  << Set x8 for 1280Mhz, or x10 for 1600Mhz
    DRAM Timing Selectable (SPD) .......... [Manual]
    
    Channel A + B + C
    
    Channel A Timing Settings:
    ##Channel A Standard Timing Control##
    CAS Latency Time ...................... 8
    tRCD ....................................... 8
    tRP ......................................... 8 
    tRAS ....................................... 24
    
    Below values may be left in Auto if you like, generally this is fine.  For those users who DO Set advanced timings manually, please see some of my thoughts and findings about these settings and rules here
    XtremeSystems Forums - View Single Post - Gigabyte EX58-UD5/Extreme Discussion Thread
    
    
    ##Channel A Advanced Timing Control##
    tRC ........................................  (Should be = tRAS + tRP or above for stability)
    tRRD .......................................
    tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
    tWR ........................................ 5-12 (Odd # values likely will fail)
    tWTP .......................................    (tWTP Must = tWR + tWL + 4)
    tWL ........................................   (tWL Must be CAS Latency -1)
    tRFC ....................................... 84-88
    tRTP .......................................
    tFAW ......................................
    Command Rate (CMD) ................ 1T  << Set this
    
    ##Channel A Misc Timing Control##
    Round Trip Latency ...................
    
    B2B CAS Delay ..........................
    
    
    Advanced Voltage Control:
    
    CPU
    Load Line Calibration ................. [Disabled]  << Enabled / Level 1
    CPU Vcore ............................... All up to your CPU, you may be fine setting stock voltage, or you may need 1.225-1.32 or so
    QPI/VTT Voltage 1.150v ............  << This is key for your memory, set 1.2-1.3 for 1280Mhz that should be fine, but you may need more.   For 1600Mhz set 1.25-1.4
    CPU PLL 1.800v ....................... 1.8
    
    MCH/ICH
    PCIE 1.500v ........................... 1.5
    QPI PLL 1.100v ....................... 1.1-1.2
    IOH Core 1.100v ..................... Auto or 1.14 should be fine
    ICH I/O 1.500v ....................... 1.5
    ICH Core 1.1v ........................ 1.1-1.14
    
    DRAM
    DRAM Voltage 1.500v .............. 1.5 for 1280Mhz, or 1.6-1.66 for 1600Mhz (You may need the full 1.65V so set 1.66 at first if you try 1600Mhz)
    DRAM Termination 0.750v [AUTO]
    Ch-A Data VRef. 0.750v [AUTO]
    Ch-B Data VRef. 0.750v [AUTO]
    Ch-C Data VRef. 0.750v [AUTO]
    Ch-A Address VRef. 0.750v [AUTO]
    Ch-B Address VRef. 0.750v [AUTO]
    Ch-C Address VRef. 0.750v [AUTO]

  6. #16
    Join Date
    Mar 2009
    Posts
    12

    Default Re: EX-58, ud4p, boot loops then freezes, repeat...

    Thanks for the settings Lsdmeasap, now I just have to enter them before it freezes. I think i should set the voltage first and save and quite and then the other settings. Im still confused by my video card and pci-e slots, it seems the the 8x slots work with my card, so I might not have cleaned the other two well enough.

  7. #17
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: EX-58, ud4p, boot loops then freezes, repeat...

    If you have major problems doing so, try using only 1-2 sticks of memory until you can get the settings entered and saved, then reboot to windows and shut down, then put in all your memory.

    Yes, you may have cleaned it too much and broke something, or the water damaged it due to not being fully dry when using it again. If there is coolant, instead of water in those, then that could have caused more damage than water as well, so not sure.

    The second PCIE slot will run at x16 too, as long as nothing is in the first PCIE Slot

  8. #18
    Join Date
    Mar 2009
    Posts
    12

    Default Re: EX-58, ud4p, boot loops then freezes, repeat...

    Well I got the settings in and saved and exited, but then the strangest thing happened. It would start up, go through all the normal stuff(start up screen, raid setup, etc) but when it came time for the os to load it would start at the start up screen again?! it did this for 2 or 3 times, then it shut down for a while and then when into a boot loop again....

    I'm thinking that this board is done for unfortunately, can't think of anything else to do.
    Thanks for helping anyway Lsdmeasap
    Last edited by willem3de; 05-16-2010 at 02:10 AM.

  9. #19
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: EX-58, ud4p, boot loops then freezes, repeat...

    No BSOD or anything?

    Does this happen also with no hard drive connected, please test. With no hard drive connected it should go through the boot process and then eventually say No hard drive or OS found, ect and just sit there waiting for you to do something.

    Test, and if that happens then we will know the hard drive or drive related settings is the cause of this

  10. #20
    Join Date
    Mar 2009
    Posts
    12

    Default Re: EX-58, ud4p, boot loops then freezes, repeat...

    Removed the hard drives, it did the same thing expect no raid screen anymore. I turned it off before it started a boot loop again, I checked the bios and all my setting are still there so that's good I guess.

Page 2 of 3 FirstFirst 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •