Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 6 of 6 FirstFirst ... 456
Results 51 to 56 of 56

Thread: New Goal: 4.2ghz q9550 + ep45-ud3p + 8gb g.skill pi black pc2-6400




  1. #51
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: New Goal: 4.2ghz q9550 + ep45-ud3p + 8gb g.skill pi black pc2-6400

    Not sure, I never run multiple sessions as it's not really needed. Too many runs of linpack is not good for CPU's

  2. #52
    Join Date
    Feb 2010
    Location
    indonesia
    Posts
    124

    Default Re: New Goal: 4.2ghz q9550 + ep45-ud3p + 8gb g.skill pi black pc2-6400

    Hmm right i'm affraid procie will get broken if i run multiple IBT session ... so now i stop test with IBT and here my latest stable 4ghz again with lower MCH 1.24volt, tested in gaming a few days with no problem :) and finally i follow prof jim or lsdmeasap advice that i should set memory performance level to standard when oc procie ^_^ the result is stable speed Gflops.
    So if i'm too much using IBT and wanna test again which stressing software should i use? prime? or OCCT?


    Uploaded with ImageShack.us

    Note: sorry too many SS in ur thread @exius ^_^ i just wanna sharing & i hope everyone else share too :) so we can learn each other.
    Intel Core i5 2500k @3.33ghz (4.5ghz 1.255v)
    MSI 67A5-GD80( B3)
    Patriot Viper Extreme D2 PXD34G13600LLK 8-9-8-24 2T 1.65v (1600mhz 8-9-8-24 2T 1.65v)
    Western Digital
    Caviar Black500G SATA2 32mb
    MSI GTX570TFII OC 750/1000 (930/1100 1.088v)
    Thermalright Archon + TY140 + CF III
    Corsair TX-650
    Windows7 Ultimate x64 SP1
    -Open rig-

  3. #53
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Thumbs up Re: New Goal: 4.2ghz q9550 + ep45-ud3p + 8gb g.skill pi black pc2-6400

    Running more than a 10 loop IBT test qualifies as cpu abuse
    I've never seen others who ran multiple simultaneous IBT sessions.

    IBT or LinX are good as a quick stability test, but I've had many times where IBT or LinX was good for 10 loops, but Prime95 and/or OCCT tests had errors. These failed tests often had errors after 2 - 10 hours. On a few occasions, the errors occurred after 13 - 15 hours. My preference is to run each of the three Prime95 or OCCT tests for at least 8 - 12 hours, running only one test at a time.
    Note: IBT and LinX each have an option to save test results to their respective program folders.

    The OCCT PSU test is a very demanding test that combines the "worst" of linpack and FurMark testing. I usually run the OCCT PSU test for no more than 30 - 60 minutes.

    You've done a great job high-jacking the thread, and you've provided good information and feedback that will help others.
    MCH Core voltage = 1.24 seems a bit low, but if it works with your setup thats OK.
    If you overclock higher, you will probably need to tweak the MCH reference and possibly CPU reference settings.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  4. #54
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: New Goal: 4.2ghz q9550 + ep45-ud3p + 8gb g.skill pi black pc2-6400

    I agree, I use 10 passes of LinX at the most. Then I use 4-6 x HCI memtest in windows using 400-1024MB each, running to 500-1000%

  5. #55
    Join Date
    Feb 2010
    Location
    indonesia
    Posts
    124

    Default Re: New Goal: 4.2ghz q9550 + ep45-ud3p + 8gb g.skill pi black pc2-6400

    Hehehe thx prof jim ^_^ i love to share and love to read others sharing in here :) sorry about "high jacking exius thread" ^^
    Btw last i ran test again with IBT 20loops level max MCH 1.24volt and yet it survived again including tight ram timing.... i set in "advanced memory timing" to 3,3,6,52,3 sorry if i type wrong hehe abit forgot ^_^ so its enough now for fsb 471 :)
    later will trying experiment with fsb 500 ... i hope i can.
    This is my last SS in exius thread guys, thx to all for helping or supporting me :) prof jim and lsdmeasap just like great mentor here in tweaktown hehe.


    Uploaded with ImageShack.us
    Intel Core i5 2500k @3.33ghz (4.5ghz 1.255v)
    MSI 67A5-GD80( B3)
    Patriot Viper Extreme D2 PXD34G13600LLK 8-9-8-24 2T 1.65v (1600mhz 8-9-8-24 2T 1.65v)
    Western Digital
    Caviar Black500G SATA2 32mb
    MSI GTX570TFII OC 750/1000 (930/1100 1.088v)
    Thermalright Archon + TY140 + CF III
    Corsair TX-650
    Windows7 Ultimate x64 SP1
    -Open rig-

  6. #56
    Join Date
    Feb 2010
    Location
    indonesia
    Posts
    124

    Default Re: New Goal: 4.2ghz q9550 + ep45-ud3p + 8gb g.skill pi black pc2-6400

    Here is my bios template for my setting in last post :

    Motherboard:EP45-UD3P, Rev#:1.1
    Bios version: F9
    Cpu:Q9550, Model:7, Ext.Model:17, Revision:EO
    Ram: Gskill RipJaws F2-PC9600CL6D-4GBRH 2x2GB
    Power Supply Unit: Cooler Master, CM-SilentPro M500, 500W


    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster -------------- : [Auto]
    CPU Clock Ratio ------------------------ : [8x]
    Fine CPU Clock Ratio ------------------ : [+0.5]
    CPU Frequency ------------------------- : 4GHz(471x8)

    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control ----------------- : [Enabled]
    CPU Host Frequency (Mhz) ------------- : [471]
    PCI Express Frequency (Mhz) ---------- : [100]
    C.I.A.2 ------------------------------------ : [Disabled]

    Advanced Clock Control --------------- : [Press Enter]
    CPU Clock Drive ------------------------ : <<< 800
    PCI Express Clock Drive --------------- : <<< 900
    CPU Clock Skew (ps) ------------------ : <<<
    MCH Clock Skew (ps) ------------------ : <<<

    DRAM Performance Control
    Performance Enhance ------------------- : [Standard]
    Extreme Memory Profile --- (X.M.P.) --- : [Disabled]
    (G)MCH Frequency Latch ---------------- : [333MHz]
    System Memory Multiplier --------------- : [2.40B]
    Memory Frequency (Mhz) ------1066---- : [1130MHz]
    DRAM Timing Selectable ----------------- : [Manual]

    Standard Timing Control
    CAS Latency Time -------- 5 ---------- : [5]
    tRCD ------------------- 5 -------------- : [5]
    tRP --------------------- 5 -------------- : [5]
    tRAS ------------------- 15 ------------ : [15]

    Advanced Timing Control
    tRRD ------------------- 4 ----------- : [3]
    tWTR ------------------- 4 ---------- : [3]
    tWR --------------------- 8 ----------- : [6]
    tRFC ------------------- 68 ---------- : [52]
    tRTP ------------------- 4 ----------- : [3]
    Command Rate (CMD) ------ 0 ----- : [Auto]

    Driving Strength Profiles
    Driving Strength --------- : [Auto]

    Channel A
    Static tRead Value ----------- 11 -------- : [8]
    tRD Phase0 Adjustment -------- 0 ------ : [Auto] <-- leave this and below set to AUTO
    tRD Phase1 Adjustment -------- 0 ------ : [Auto]
    tRD Phase2 Adjustment -------- 0 ------ : [Auto]
    tRD Phase3 Adjustment -------- 0 ------ : [Auto]
    Trd2rd(Different Rank) ------- 6 -------- : [Auto]
    Twr2wr(Different Rank) ------- 6 ------- : [Auto]
    Twr2rd(Different Rank) ------- 5 ------- : [Auto]
    Trd2wr(Same/Diff Rank) ------- 8 ------ : [Auto]
    Dimm1 Clock Skew Control -------------- : [Auto]
    Dimm2 Clock Skew Control -------------- : [Auto]

    Channel B
    Static tRead Value ----------- 11 ------- : [8]
    tRD Phase0 Adjustment -------- 0 ------ : [Auto] <-- leave this and below set to AUTO
    tRD Phase1 Adjustment -------- 0 ------ : [Auto]
    tRD Phase2 Adjustment -------- 0 ------ : [Auto]
    tRD Phase3 Adjustment -------- 0 ------ : [Auto]
    Trd2rd(Different Rank) ------- 6 ------- : [Auto]
    Twr2wr(Different Rank) ------- 6 ------ : [Auto]
    Twr2rd(Different Rank) ------- 5 ------- : [Auto]
    Trd2wr(Same/Diff Rank) ------- 8 ------ : [Auto]
    Dimm1 Clock Skew Control -------------- : [Auto]
    Dimm2 Clock Skew Control -------------- : [Auto]

    Motherboard Voltage Control
    Load Line Calibration ------------------: [Enabled]
    CPU
    CPU Vcore --------------- 1.30000V ------: [1.35625V]
    CPU Termination --------- 1.200V* ----- : [1.300V]
    CPU PLL ----------------- 1.500V* ------- : [1.500V]
    CPU Reference ----------- 0.760* ------- : [Auto]--->0.823V
    CPU Reference2 ---------- ?????* ------- : [Dont have this option]

    MCH/ICH
    MCH Core ---------------- 1.100V --------- : [1.240V]
    MCH Reference ----------- 0.760V -------- : [Auto]--->0.823V
    MCH/DRAM Ref ------------ 0.900V ------ : [Auto]
    ICH I/O ----------------- 1.500V ----------- : [1.500V]
    ICH Core ---------------- 1.100V ---------- : [1.100V]
    DRAM
    DRAM Voltage ------------ 1.800V -------- : [1.960V]
    DRAM Termination -------- 0.900V ------- : [Auto]
    Channel A Reference ----- 0.900V -------- : [Auto]
    Channel B Reference ----- 0.900V -------- : [Auto]

    Advanced Settings
    Limit CPUID Max. to 3 --------------------- : [Disabled]
    No-Execute Memory Protect -------------- : [Enabled]
    CPU Enhanced Halt (C1E) ----------------- : [Disabled]
    C2/C2E State Support --------------------- : [Disabled]
    x C4/C4E State Support ------------------- : [Disabled]
    CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
    CPU EIST Function ------------------------ : [Disabled]
    Virtualization Technology ----------------- : [Disabled]

    Integrated Peripherals
    Legacy USB Storage Detect ------------- : [Disabled]

    Hope may help others :) see u next time "exius" ^_^
    Last edited by Neoroy; 11-17-2010 at 10:13 PM.
    Intel Core i5 2500k @3.33ghz (4.5ghz 1.255v)
    MSI 67A5-GD80( B3)
    Patriot Viper Extreme D2 PXD34G13600LLK 8-9-8-24 2T 1.65v (1600mhz 8-9-8-24 2T 1.65v)
    Western Digital
    Caviar Black500G SATA2 32mb
    MSI GTX570TFII OC 750/1000 (930/1100 1.088v)
    Thermalright Archon + TY140 + CF III
    Corsair TX-650
    Windows7 Ultimate x64 SP1
    -Open rig-

Page 6 of 6 FirstFirst ... 456

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •