Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 6 of 16 FirstFirst ... 45678 ... LastLast
Results 51 to 60 of 151

Thread: Help Please For A Newbie Noobie :)




  1. #51
    micky22 is offline Junior Member
    Join Date
    Jun 2010
    Location
    N.E England
    Posts
    85

    Default Re: Help Please For A Newbie Noobie :)

    OK m8 have done sig although am not sure y its not showing but here it is anyway :)

    Mobo:GA-X58A-UD3R
    CPU: i7 930
    CPU Cooler: Zalman CNPS9900A LED
    Ram: 6GB OCZ Gold 1600MHZ (OCZ3G16000LV2G)
    HDD: 500Gb WD HDD (Looking to upgrade to a Samsung 1TB F3 ASAP )
    GFX: 9800GTX 512Mb (Looking to upgrade in the near future)
    Power Supply: Corsair TX750w
    Bios:F5
    Mobo: Asus Crosshair V Formula-Z
    CPU: AMDFX 8350 Black
    CPU Cooler: Corsair H70
    Ram: Corsair CMX8GX3M2A1333c9 (Looking to upgrade)
    HDD: OCZ Solid 3 60Gb Plus WD 1tb
    GFX: GTS250 (Looking to upgrade in the near future)
    Power Supply: Corsair GS600
    Bios:1302

  2. #52
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Help Please For A Newbie Noobie :)

    Sig only shows in new posts, after you add it into your profile.

    Try this for 3.8

    Wait, before I finish the below settings, can you give me a link to your memory, I can't find that by model # anywhere.


    BSOD Error codes and what they mean:
    0X00000050 << Incorrect Memory Timing/Freq or Uncore Multi
    0X00000124 << Incorrect QPI/Vtt Voltage (To Much/Not Enough)
    0X00000101 << Not enough Vcore Voltage

    Code:
    Advanced CPU Features:
    CPU Clock Ratio ................................ [19x]
    Intel(R) Turbo Boost Tech .................. [Enabled]  << Disabled
    CPU Cores Enabled ............................ [All]
    CPU Multi Threading .......................... [Enabled]
    CPU Enhanced Halt (C1E) ................... [Disabled]  
    C3/C6/C7 State Support .................... [Disabled]
    CPU Thermal Monitor ......................... [Enabled]
    CPU EIST Function ............................ [Disabled]
    Virtualization Technology ................... [Enabled] << Disabled if you do not use Vmware or Virtual PC Programs
    Bi-Directional PROCHOT ..................... [Enabled]
    
    
    Uncore & QPI Features:
    QPI Link Speed .............................. x36
    Uncore Frequency ..........................  (Always 2x memory Multi or 2x +1, 2x +2, ect - Higher means more Vdimm or QPI/Vtt often but can help stability)  So use x16-18
    Isonchronous Frequency ..................[Enabled]
    
    
    Standard Clock Control:
    Base Clock (BCLK) Control ................ [Enabled]
    BCLK Frequency (MHz) ..................... 200
    PCI Express Frequency (MHz) ........... [100]
    
    C.I.A.2 [Disabled]
    
    Advanced Clock Control:
    CPU Clock Drive ..............................[800mV]
    PCI Express Clock Drive ................... [900mV]
    CPU Clock Skew ............................. [0ps]
    IOH Clock Skew ............................. [0ps]
    
    
    Advanced DRAM Features:
    Performance Enhance ...................... [Standard] << Extreme may be best
    Extreme Memory Profile (X.M.P) ......... [Disabled]
    System Memory Multiplier (SPD) ........ [AUTO]  << Set x8 = 1600mhz
    DRAM Timing Selectable (SPD) .......... [Manual]
    
    Channel A + B + C
    
    Channel A Timing Settings:
    ##Channel A Standard Timing Control##
    CAS Latency Time ...................... 7/8/9
    tRCD .......................................  7/8/9
    tRP .........................................  7/8/9
    tRAS ....................................... 20/24
    
    ^^ Set to what you find on your ram sticker once you get a chance to look ^^
    
    Below values may be left in Auto if you like, generally this is fine.  For those users who DO Set advanced timings manually, please see some of my thoughts and findings about these settings and rules here
    XtremeSystems Forums - View Single Post - Gigabyte EX58-UD5/Extreme Discussion Thread
    
    
    ##Channel A Advanced Timing Control##
    tRC ........................................  (Should be = tRAS + tRP or above for stability)
    tRRD .......................................
    tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
    tWR ........................................ 5-12 (Odd # values likely will fail)
    tWTP .......................................    (tWTP Must = tWR + tWL + 4)
    tWL ........................................   (tWL Must be CAS Latency -1)
    tRFC .......................................
    tRTP .......................................
    tFAW ......................................
    Command Rate (CMD) ................
    
    ##Channel A Misc Timing Control##
    Round Trip Latency ...................
    
    B2B CAS Delay ..........................
    
    
    Advanced Voltage Control:
    
    CPU
    Load Line Calibration ................. [Disabled]
    CPU Vcore ............................... All up to your CPU, try 1.25-1.35 may need more or less
    QPI/VTT Voltage 1.150v ............ 1.3-1.35 should be good
    CPU PLL 1.800v ....................... 1.8
    
    MCH/ICH
    PCIE 1.500v ...........................
    QPI PLL 1.100v ....................... 1.2
    IOH Core 1.100v ..................... 1.14
    ICH I/O 1.500v .......................
    ICH Core 1.1v ........................
    
    DRAM
    DRAM Voltage 1.500v ..............  << Set to ram spec, if 1.65V set 1.66
    DRAM Termination 0.750v [AUTO]
    Ch-A Data VRef. 0.750v [AUTO]
    Ch-B Data VRef. 0.750v [AUTO]
    Ch-C Data VRef. 0.750v [AUTO]
    Ch-A Address VRef. 0.750v [AUTO]
    Ch-B Address VRef. 0.750v [AUTO]
    Ch-C Address VRef. 0.750v [AUTO]
    Last edited by Lsdmeasap; 06-24-2010 at 05:24 PM.

  3. #53
    micky22 is offline Junior Member
    Join Date
    Jun 2010
    Location
    N.E England
    Posts
    85

    Default Re: Help Please For A Newbie Noobie :)

    I bought my ram from overclockers but it seem my model aint there no more and the same as u i cant find it anywere but that is defo the correct model no :)

    http://i45.tinypic.com/347z3h1.jpg
    Mobo: Asus Crosshair V Formula-Z
    CPU: AMDFX 8350 Black
    CPU Cooler: Corsair H70
    Ram: Corsair CMX8GX3M2A1333c9 (Looking to upgrade)
    HDD: OCZ Solid 3 60Gb Plus WD 1tb
    GFX: GTS250 (Looking to upgrade in the near future)
    Power Supply: Corsair GS600
    Bios:1302

  4. #54
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

  5. #55
    micky22 is offline Junior Member
    Join Date
    Jun 2010
    Location
    N.E England
    Posts
    85

    Default Re: Help Please For A Newbie Noobie :)

    Not sure what u mean m8 :)

    EDIT:
    If i contacted OCZ would they tell me specs? or is there another way to find specs?
    Last edited by micky22; 06-24-2010 at 04:19 PM. Reason: Added More Info!
    Mobo: Asus Crosshair V Formula-Z
    CPU: AMDFX 8350 Black
    CPU Cooler: Corsair H70
    Ram: Corsair CMX8GX3M2A1333c9 (Looking to upgrade)
    HDD: OCZ Solid 3 60Gb Plus WD 1tb
    GFX: GTS250 (Looking to upgrade in the near future)
    Power Supply: Corsair GS600
    Bios:1302

  6. #56
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Help Please For A Newbie Noobie :)

    I mean like ya know, 999-24 @ 1.65V

    Like that, should even be on a sticker on your memory most likely.

  7. #57
    micky22 is offline Junior Member
    Join Date
    Jun 2010
    Location
    N.E England
    Posts
    85

    Default Re: Help Please For A Newbie Noobie :)

    Or ok am with u now lol not at home atm but as soon as i get home ill post them cheers :)

    EDIT:

    I no 100% timing is 8 8 8 but i cant remember what the voltage is
    Last edited by micky22; 06-24-2010 at 05:16 PM.
    Mobo: Asus Crosshair V Formula-Z
    CPU: AMDFX 8350 Black
    CPU Cooler: Corsair H70
    Ram: Corsair CMX8GX3M2A1333c9 (Looking to upgrade)
    HDD: OCZ Solid 3 60Gb Plus WD 1tb
    GFX: GTS250 (Looking to upgrade in the near future)
    Power Supply: Corsair GS600
    Bios:1302

  8. #58
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Help Please For A Newbie Noobie :)

    OK, well I will put a general setting there, then you can use whatever is on your sticks once you get home and look at them

    I'll edit the above now.

  9. #59
    micky22 is offline Junior Member
    Join Date
    Jun 2010
    Location
    N.E England
    Posts
    85

    Default Re: Help Please For A Newbie Noobie :)

    ok thanks very much m8
    Mobo: Asus Crosshair V Formula-Z
    CPU: AMDFX 8350 Black
    CPU Cooler: Corsair H70
    Ram: Corsair CMX8GX3M2A1333c9 (Looking to upgrade)
    HDD: OCZ Solid 3 60Gb Plus WD 1tb
    GFX: GTS250 (Looking to upgrade in the near future)
    Power Supply: Corsair GS600
    Bios:1302

  10. #60
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

Page 6 of 16 FirstFirst ... 45678 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •