Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 4 of 9 FirstFirst ... 23456 ... LastLast
Results 31 to 40 of 86

Thread: Pre-OC'ing temp check (idle/load) for X58A-UD3R + i7 930 + Megahalems




  1. #31
    Join Date
    Apr 2010
    Location
    Auckland, NZ
    Posts
    75

    Default Re: Pre-OC'ing temp check (idle/load) for X58A-UD3R + i7 930 + Megahalems

    In BIOS i set my config at 21x180 = 3.78 Ghz

    But in CPUZ it's 22x180 = 3.96 Ghz since turbo is on, and passed Prime for 7 hours, so Im guessing its pretty stable around 3.8-4ghz

    So should I be turning turbo off or ?

    I'd like to try to get 4.2 Ghz next
    Last edited by chiggah; 06-30-2010 at 10:23 AM.

  2. #32
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Pre-OC'ing temp check (idle/load) for X58A-UD3R + i7 930 + Megahalems

    Turbo is up to you, since you are stable you may be ok though. Normally I'd say not to use the x22 multi, but since you are stable you may be ok

    If you want to go higher I do suggest you disable turbo and use the x21 multi

    For 1800Mhz or so, it's all up to your memory. Try 999-24 first, then if that works test and see if you can then lower to maybe 898-24 or 888-24, ect.
    Last edited by Lsdmeasap; 06-30-2010 at 04:08 PM.

  3. #33
    Join Date
    Apr 2010
    Location
    Auckland, NZ
    Posts
    75

    Default Re: Pre-OC'ing temp check (idle/load) for X58A-UD3R + i7 930 + Megahalems

    What should the rule be ? Increase BLCK first before multiplier ?

  4. #34
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Pre-OC'ing temp check (idle/load) for X58A-UD3R + i7 930 + Megahalems

    Well since you have 920/930 you would increase Bclk.

    Just use x21, I say this because Even (22) CPU multi's are often unstable and or need much more voltage than Odd ones do.

  5. #35
    Join Date
    Apr 2010
    Location
    Auckland, NZ
    Posts
    75

    Default Re: Pre-OC'ing temp check (idle/load) for X58A-UD3R + i7 930 + Megahalems

    Code:
    Advanced CPU Features:
    CPU Clock Ratio ................................ [20x] [21x]
    Intel(R) Turbo Boost Tech .................. [Enabled]
    CPU Cores Enabled ............................ [All]
    CPU Multi Threading .......................... [Enabled]
    CPU Enhanced Halt (C1E) ................... [Disabled]
    C3/C6/C7 State Support .................... [Disabled]
    CPU Thermal Monitor ......................... [Enabled]
    CPU EIST Function ............................ [Disabled] [Enabled]
    Virtualization Technology ................... [Enabled] << Disabled if you do not use Vmware or Virtual PC Programs
    Bi-Directional PROCHOT ..................... [Enabled]
    
    
    Uncore & QPI Features:
    QPI Link Speed .............................. [x36]
    Uncore Frequency ..........................  [x16]
    Isonchronous Frequency ..................[Enabled]
    
    
    Standard Clock Control:
    Base Clock (BCLK) Control ................ [Enabled]
    BCLK Frequency (MHz) ..................... [180]
    PCI Express Frequency (MHz) ........... [100]
    
    C.I.A.2 [Disabled]
    
    Advanced Clock Control:
    CPU Clock Drive ..............................[800mV]
    PCI Express Clock Drive ................... [900mV]
    CPU Clock Skew ............................. [0ps]
    IOH Clock Skew ............................. [0ps]
    
    
    Advanced DRAM Features:
    Performance Enhance ...................... [Standard]
    Extreme Memory Profile (X.M.P) ......... [Disabled]
    System Memory Multiplier (SPD) ........ [x8]
    DRAM Timing Selectable (SPD) .......... [Manual]
    
    Channel A + B + C
    
    Channel A Timing Settings:
    ##Channel A Standard Timing Control##
    CAS Latency Time ...................... [9]
    tRCD ....................................... [9]
    tRP ......................................... [9]
    tRAS ....................................... [24]
    
    Below values may be left in Auto if you like, generally this is fine.  For those users who DO Set advanced timings manually, please see some of my thoughts and findings about these settings and rules here
    XtremeSystems Forums - View Single Post - Gigabyte EX58-UD5/Extreme Discussion Thread
    
    ##Channel A Advanced Timing Control##
    tRC ........................................ [Auto]  (Should be = tRAS + tRP or above for stability)
    tRRD ....................................... [Auto]
    tWTR ...................................... [Auto] (Must be Write to Read Delay/Same Rank - (tWL + 4)
    tWR ........................................ [Auto]
    tWTP ....................................... [Auto]   (tWTP Must = tWR + tWL + 4)
    tWL ........................................ [Auto]    (tWL Must be CAS Latency -1)
    tRFC ....................................... [Auto]
    tRTP ....................................... [Auto]
    tFAW ...................................... [Auto]
    Command Rate (CMD) ................ [2]
    
    ##Channel A Misc Timing Control##
    Round Trip Latency ................... [Auto]
    
    B2B CAS Delay .......................... [Auto]
    
    
    Advanced Voltage Control:
    
    CPU
    Load Line Calibration ................. [Disabled] [Level 1]
    CPU Vcore ............................... [Normal]
    QPI/VTT Voltage 1.150v ............  [1.355V]
    CPU PLL 1.800v ....................... [Auto]
    
    MCH/ICH
    PCIE 1.500v ........................... [1.5v]
    QPI PLL 1.100v ....................... [Auto]
    IOH Core 1.100v ..................... [Auto]
    ICH I/O 1.500v ....................... [Auto]
    ICH Core 1.1v ........................ [Auto]
    
    DRAM
    DRAM Voltage 1.500v .............. [1.5V] but memory is rated at [1.6V] should I try ?
    DRAM Termination 0.750v [AUTO]
    Ch-A Data VRef. 0.750v [AUTO]
    Ch-B Data VRef. 0.750v [AUTO]
    Ch-C Data VRef. 0.750v [AUTO]
    Ch-A Address VRef. 0.750v [AUTO]
    Ch-B Address VRef. 0.750v [AUTO]
    Ch-C Address VRef. 0.750v [AUTO]

  6. #36
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Pre-OC'ing temp check (idle/load) for X58A-UD3R + i7 930 + Megahalems

    You need to disable Turbo if you want to use x21 CPU multi

  7. #37
    Join Date
    Apr 2010
    Location
    Auckland, NZ
    Posts
    75

    Default Re: Pre-OC'ing temp check (idle/load) for X58A-UD3R + i7 930 + Megahalems

    Yeah I will, but those are my current stable settings at 3.960 GHz

    Can you recommend me any tweaks I should try for 4.1 - 4.2 next ?

  8. #38
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Pre-OC'ing temp check (idle/load) for X58A-UD3R + i7 930 + Megahalems

    Well as mentioned above use turbo disable, set 21 CPU multi.

    Uncore of 17-18 will help performance, to use this you may need a little more QPi/Vtt or definitely more Dram voltage

    Rest looks fine, ohh set your own CPU PLL

  9. #39
    Join Date
    Apr 2010
    Location
    Auckland, NZ
    Posts
    75

    Default Re: Pre-OC'ing temp check (idle/load) for X58A-UD3R + i7 930 + Megahalems

    Gonna try one notch QPI/VTT

    1.6v Dram

    CPU PLL 1.84v

    Looks good ?

  10. #40
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

Page 4 of 9 FirstFirst ... 23456 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •