Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 7 of 7

Thread: GA-790xta-ud4 and ocz3g1333lvam4gk




  1. #1
    Join Date
    Jul 2010
    Location
    Dallas
    Posts
    4

    Default GA-790xta-ud4 and ocz3g1333lvam4gk

    I have a GA-790xta-ud4 board and initially installed 4 gigs of ocz3g1333lv4gk memory in it with 2 sticks.
    Obviously had crashes due to incompatibility and obtained 4 gigs of ocz3g1333lvam4gk memory for am3 systems per ocz recommendation. Swapped out sticks and now computer just beeps once when turned on and then shuts off. No post at all. I pulled out cmos for 20 mins or so along with the cpu just in case something in cache doubt it but did anyway to rule out possible doubts. Put initial 2 sticks of 4 gig total ocz3g133lv4gk memory back in since computer at least went into windows, but same scenario.
    Also, did update the bios before the memory swap but it was flashed successfully.
    I'd appreciate any insight or assistance.

    System specs:
    Athlon II X4 635
    460watts cooler master psu
    GA-790xta-ud4
    radeon hd5670
    1 dvd drive
    2 120mm fans
    500gb barracuda 7200 hd
    then the memory
    Last edited by kebersan; 07-03-2010 at 07:13 AM. Reason: add info

  2. #2
    Join Date
    Jul 2010
    Location
    Dallas
    Posts
    4

    Default Re: GA-790xta-ud4 and ocz3g1333lvam4gk

    I've also tried swapping with a 650 watt psu that I have and made sure all connections were seated and took video card out and reseated. Pulled the mem sticks out and tried 1 stick in slot 4 and all the way down same result.
    Tried swapping video card out with 8800gt video card. No difference.
    Is the one beep I hear before the computer shuts off a beep code? If so, what does one beep mean?
    Last edited by kebersan; 07-03-2010 at 06:01 AM. Reason: update

  3. #3
    Join Date
    Jul 2010
    Location
    Dallas
    Posts
    4

    Default Re: GA-790xta-ud4 and ocz3g1333lvam4gk

    Update: obtained am3 processor from a friend that has a lot of spare parts due to building computers for people a lot in the past, but unfortunately no motherboard to try and no memory since he only has ddr2- no change thus far.

  4. #4
    Join Date
    Jul 2010
    Location
    Dallas
    Posts
    4

    Default Re: GA-790xta-ud4 and ocz3g1333lvam4gk

    Update: Decided to go ahead and exchange the mainboard at the store. Put system back together and the computer posts and can go into windows.

    The memory states the following:
    CL 9-9-9-20
    (CAS-TRCD-TRP-TRAS) and 1.65 volts

    This may be a stupid question, but what do these numbers correspond to in this board's bios? I'm not running that computer for now since I'm not sure if the default values somehow damaged something last time.
    Last edited by kebersan; 07-03-2010 at 10:34 AM. Reason: clarification

  5. #5
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-790xta-ud4 and ocz3g1333lvam4gk

    Nice to see you got this sorted out!

    Those are the MAIN memory timings, and the memory voltage, auto may or may not (likely) set them correctly, you should set them youself

  6. #6
    Join Date
    Oct 2009
    Location
    Indonesia
    Posts
    74

    Default Re: GA-790xta-ud4 and ocz3g1333lvam4gk

    sorry, wrong post, i don't know how to delete post in this forum :P
    AMD Phenom II X4 955 BE 3.2Ghz
    Gigabyte GA-MA790XT-UD4P rev 1.0 F7
    Sapphire Vapor-X HD4870 1GB DDR5
    OCZ Gold AMD LV 4GB kit 9-9-9-20 1333Mhz (OCZ3G1333LVAM4GK)
    Seagate Barracuda 500GB 7200.12 SATA
    CoolerMaster RC690 BLACK PURE (stock fans) + Clear Side Window
    FSP Epsilon 85PLUS 600 watt
    AVR Matsunaga 1000N
    Xigmatek HDT-s1283 Red Scorpion
    Windows 7 Ultimate 64 bit
    Pioneer DVR-S18L 22x22 SATA
    Samsung SyncMaster 733NW
    2+1 Altec Lansing AVS300

  7. #7
    Join Date
    Apr 2009
    Location
    Virginia
    Posts
    1,470

    Default Re: GA-790xta-ud4 and ocz3g1333lvam4gk

    First Load Optimized Defaults in BIOS. Before you install the new memory. After you install the memory. See how it works on auto settings. Sometimes it sets the memory up correctly.
    If it doesn't you may want to set the memory and timing items manually.
    Here is a template with some manual settings for the OCZ 3g1333lvam4gk
    OCZ DDR3 PC3-10666 Gold AMD Edition Low Voltage OCZ Technology
    Code:
    CMOS Setup Utility-Copyright (C) 1984-2009 Award Software
     MB Intelligent Tweaker(M.I.T.)  Load Fail-Safe Defaults
     Standard CMOS Features          Load Optimized Defaults Press Enter Save and Exit.
     Advanced BIOS Features          Set Supervisor Password
     Integrated Peripherals          Set User Password
     Power Management Setup          Save & Exit Setup
     PC Health Status                Exit Without Saving
    After you change the voltage and set the DDR3 Timing Items to manual save and exit reboot go back into BIOS and then change the memory timings.
    Code:
    MB Intelligent Tweaker(M.I.T.)
    } Advanced Clock Calibration [Press Enter]
    CPU Clock Ratio [Auto] 2800Mhz
    CPU NorthBridge Freq. [Auto] 2000Mhz
    CPU Host Clock Control [Auto]
    x CPU Frequency(MHz) 200
    PCIE Clock(MHz) [Auto]
    HT Link Width [Auto]
    HT Link Frequency [Auto] 2000Mhz
    Set Memory Clock [Auto]
    x Memory Clock x6.66 1333Mhz
    } DRAM Configuration [Press Enter] 
    ******** System Voltage Optimized ********
    System Voltage Control [Auto]
    x SATA3 Volt Control Auto
    x CPU PLL Voltage Control Auto
    x DRAM Voltage Control +0.15V=1.65v
    x DDR VTT Voltage Control Auto
    x NB Voltage Control Auto
    x SB/HT Voltage Control Auto
    x NB/PCIe/PLL Voltage Control Auto
    x CPU NB VID Control Auto
    x CPU Voltage Control Auto
    Normal CPU Vcore 1.3250V
    Do not pay any attention to the numbers in the SPD column and the Auto column. These are for reference only. They can not be changed. Only the manual line can be changed after you set it to manual save exit, and reboot.
    Code:
    DRAM Configuration
    CPU Host Clock Control [Auto]
    x CPU Frequency(MHz) 200
    Set Memory Clock [Auto]
    x Memory Clock x6.66 1333Mhz
    DCTs Mode [Unganged]
    DDR3 Timing Items [Manual] SPD Auto
    x CAS# latency 9T 9T 9T
    x RAS to CAS R/W Delay 9T 9T 9T
    x Row Precharge Time 9T 9T 9T
    x Minimum RAS Active Time 20T 20T 20T
    x 1T/2T Command Timing Auto -- --
    x TwTr Command Delay Auto 5T 5T
    x Trfc0 for DIMM1 Auto 110ns 110ns
    x Trfc2 for DIMM2 Auto -- --
    x Trfc1 for DIMM3 Auto -- --
    x Trfc3 for DIMM4 Auto -- --
    x Write Recovery Time Auto 10T 10T
    x Precharge Time Auto 5T 5T
    x Row Cycle Time 30T 30T 30T
    Save exit and rebbot several times as you make changes.
    Let us know how that goes.
    Last edited by artdrivers; 07-18-2010 at 12:59 PM.
    http://forums.tweaktown.com/gigabyte...ench-test.html
    http://www.gigabyte-usa.com/FileList...ios_qflash.pdf
    Phenom II 945 @ 3.2Ghz w/Thermaltake Big Typhoon Pro 14 CPU Cooler
    Gigabyte GA-MA78GM-S2H rev.1.1 F11
    Sapphire 3870HD / 100225L / 512MB / ddr4
    4GB / Kingston / KHX8500D2K2/2GN / 5-5-5-18 / 1066Mhz
    (2) WD Caviar / WD2500AAKS/ 250GB in SATA RAID-0
    (1) WD Caviar / WD2500AAKS/ 250GB in SATA AHCI
    (2) IDE's 1 8XdualDVDRW 1 52x32x52x CDRW
    Antec /Neo HE550 / 550W
    Mid size ATX case with show through panel
    2) 80x80 front fans (1) 120x120 rear fan and small nb fan
    Microsoft comfort curve USB keyboard 2000 ver.1.0
    Logitech G500 USB mouse
    Monitor: CMV937A
    7.1+2 Channel High Definition ALC889A
    Dual boot Windows 7 32bit home & Windows 7 64bit home


Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •