Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 4 of 14 FirstFirst ... 23456 ... LastLast
Results 31 to 40 of 136

Thread: help overclocking Q6600 with GA-EP45 UD3L




  1. #31
    Join Date
    Aug 2010
    Location
    Montreal
    Posts
    91

    Default Re: help overclocking Q6600 with GA-EP45 UD3L

    Motherboard: GA-EP45-UD3L: Rev 1.1: F9:
    Cpu: Q6600
    Ram: Brand, Model/Part#, Link to your ram's specs
    Power Supply Unit: Antec, Model TP650, ^650

    note: replace all ?? with the value displayed in your bios.
    ----> Replace "Auto" with manually set values.

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster -------------- : [Auto]
    CPU Clock Ratio ---------------------- : [9]
    Fine CPU Clock Ratio ----------------- : [0.0] <-- ignore if not available
    CPU Frequency ---------------------: 2.40 to 3.ghz <-- this is set by your bios

    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control --------------- : [Disabled]
    CPU Host Frequency (Mhz) --------------: [333]
    PCI Express Frequency (Mhz) ---------- : [100] <--- Set to 100, never leave this on Auto

    C.I.A.2 ------------------------------ : [Disabled]

    Advanced Clock Control ------- [Press Enter]
    CPU Clock Drive ---------------------- : [800mv]
    PCI Express Clock Drive -------------- : [800mv]
    CPU Clock Skew (ps) ------------------ : [0ps]
    MCH Clock Skew (ps) ------------------ : [0ps]

    DRAM Performance Control
    Performance Enhance ------------------- : [Standard] <--- set to STANDARD when overclocking
    Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <--- Leave this Disabled
    (G)MCH Frequency Latch ---------------- : [Auto]
    System Memory Multiplier -------------- : [2.40B] <-- this is the setting that you are using
    Memory Frequency (Mhz) ---------------- : [667/800]
    DRAM Timing Selectable ---------------- : [Manual] <-- set to MANUAL for overclocking

    Standard Timing Control
    CAS Latency Time -------- 5 ---------- : [5]
    tRCD ------------------- 5---------- : [5]
    tRP --------------------- 5 ---------- : [5]
    tRAS ------------------- 15 ---------- : [15]

    Advanced Timing Control
    tRRD ------------------- 3---------- : [Auto]
    tWTR ------------------- 3 ---------- : [Auto]
    tWR --------------------- 5 ---------- : [Auto]
    tRFC ------------------- 44 ---------- : [Auto]
    tRTP ------------------- 3 ---------- : [Auto]
    Command Rate (CMD) -------------------- : [Auto] <--- Auto or 0 is OK

    Driving Strength Profiles
    Driving Strength --------- : Press Enter <--- press ENTER to modify memory sub-timings when overclocking

    Channel A
    Static tRead Value --------------------- : [Auto]
    tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
    tRD Phase1 Adjustment ------------------ : [Auto]
    tRD Phase2 Adjustment ------------------ : [Auto]
    tRD Phase3 Adjustment ------------------ : [Auto]
    Trd2rd(Different Rank) ----------------- : [Auto]
    Twr2wr(Different Rank) ----------------- : [Auto]
    Twr2rd(Different Rank) ----------------- : [Auto]
    Trd2wr(Same/Diff Rank) ----------------- : [Auto]
    Dimm1 Clock Skew Control --------------- : [Auto] ps
    Dimm2 Clock Skew Control --------------- : [Auto] ps

    Channel B
    Static tRead Value --------------------- : [Auto]
    tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
    tRD Phase1 Adjustment ------------------ : [Auto]
    tRD Phase2 Adjustment ------------------ : [Auto]
    tRD Phase3 Adjustment ------------------ : [Auto]
    Trd2rd(Different Rank) ----------------- : [Auto]
    Twr2wr(Different Rank) ----------------- : [Auto]
    Twr2rd(Different Rank) ----------------- : [Auto]
    Trd2wr(Same/Diff Rank) ----------------- : [Auto]
    Dimm1 Clock Skew Control --------------- : [Auto] ps
    Dimm2 Clock Skew Control --------------- : [Auto] ps

    Motherboard Voltage Control
    CPU
    Voltage Types------------ Normal -------- Current -----
    Load-Line Calibration ----------------- : [Enabled]
    CPU Vcore --------------- 1.3000v---- : [1.3000v]

    CPU Termination --------- 1.200V* ----- : [1.200v]
    CPU PLL ----------------- 1.550V* ----- : [1.550v]

    CPU Reference ----------- 0.805V* ----- : [Auto]
    CPU Reference2 ---------- ?.???V* ----- : [Auto] N/A

    MCH/ICH
    MCH Core ---------------- 1.100V ------- : [1.200V]
    MCH Reference ----------- 0.760V ------- : [Auto]
    MCH/DRAM Ref ------------ ?.???V ------ : [Auto] N/A
    ICH I/O ----------------- 1.550V ------- : [1.550v]
    ICH Core ---------------- 1.100V ------- : [1.100v]
    DRAM
    DRAM Voltage ------------ 1.800V ------- : [1.860v]
    DRAM Termination -------- ?.???V ------- : [Auto] N/A
    Channel A Reference ----- ?.???V ------- : [Auto]N/A
    Channel B Reference ----- ?.???V ------- : [Auto]N/A

    Advanced Settings
    Limit CPUID Max. to 3 ------------------ : [Disabled]
    No-Execute Memory Protect -------------- : [Enabled]
    CPU Enhanced Halt (C1E) ---------------- : [Disabled]
    C2/C2E State Support ------------------- : [Disabled]
    x C4/C4E State Support ----------------- : [Disabled]
    CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
    CPU EIST Function --------------------- : [Disabled]
    Virtualization Technology -------------- : [Disabled]

    Integrated Peripherals
    Legacy USB Storage Detect ------------- : [Disabled]
    Last edited by namal245; 08-14-2010 at 02:19 AM.
    GA-EP45-UD3L REV 1.1 bios F9
    INTEL Core 1 Quad Q6600 2.4ghz to 3.2ghz
    Zalman CNPS 9700 LED 2800 RPM
    Corsair CM2X PC-6400 2X 1024MB http://www.corsair.com/_datasheets/CM2X1024-6400.pdf
    Kingston KHX6400 2x2048MB http://www.valueram.com/datasheets/KHX6400D2K2_4G.pdf
    Zotac GTS 250 1024GB DDR3
    Antec Nine hundred 2 case http://www.antec.com/Believe_it/product.php?id=NzIy
    PSU Antec Truepower series TP650 http://www.antec.com/Believe_it/product.php?id=MTc1OQ==
    DELL 20" Monitor

  2. #32
    Join Date
    Aug 2010
    Location
    Montreal
    Posts
    91

    Default Re: help overclocking Q6600 with GA-EP45 UD3L

    that my current settings overclocked. now to test with prime95 for the rest of the day. and memtest too.
    GA-EP45-UD3L REV 1.1 bios F9
    INTEL Core 1 Quad Q6600 2.4ghz to 3.2ghz
    Zalman CNPS 9700 LED 2800 RPM
    Corsair CM2X PC-6400 2X 1024MB http://www.corsair.com/_datasheets/CM2X1024-6400.pdf
    Kingston KHX6400 2x2048MB http://www.valueram.com/datasheets/KHX6400D2K2_4G.pdf
    Zotac GTS 250 1024GB DDR3
    Antec Nine hundred 2 case http://www.antec.com/Believe_it/product.php?id=NzIy
    PSU Antec Truepower series TP650 http://www.antec.com/Believe_it/product.php?id=MTc1OQ==
    DELL 20" Monitor

  3. #33
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: help overclocking Q6600 with GA-EP45 UD3L

    Leave CPU/MCH references on auto.
    You may need more Vcore. You may enable LLC(Load Line Calibration) which will help using less Vcore.
    Begin stressing with couple of hours Prime95/Orthos small FFT followed by a couple of hours large FFT, and then 8-12 hours Blend torture.
    FFT size may indicate what need to be changed, so remember which one cause failure if you have any.

  4. #34
    Join Date
    Aug 2010
    Location
    Montreal
    Posts
    91

    Default Re: help overclocking Q6600 with GA-EP45 UD3L

    ok cool i will do that i am on my other pc lol
    GA-EP45-UD3L REV 1.1 bios F9
    INTEL Core 1 Quad Q6600 2.4ghz to 3.2ghz
    Zalman CNPS 9700 LED 2800 RPM
    Corsair CM2X PC-6400 2X 1024MB http://www.corsair.com/_datasheets/CM2X1024-6400.pdf
    Kingston KHX6400 2x2048MB http://www.valueram.com/datasheets/KHX6400D2K2_4G.pdf
    Zotac GTS 250 1024GB DDR3
    Antec Nine hundred 2 case http://www.antec.com/Believe_it/product.php?id=NzIy
    PSU Antec Truepower series TP650 http://www.antec.com/Believe_it/product.php?id=MTc1OQ==
    DELL 20" Monitor

  5. #35
    Join Date
    Aug 2010
    Location
    Montreal
    Posts
    91

    Default Re: help overclocking Q6600 with GA-EP45 UD3L

    so far good on blend testing now for rest of the day no error yet
    GA-EP45-UD3L REV 1.1 bios F9
    INTEL Core 1 Quad Q6600 2.4ghz to 3.2ghz
    Zalman CNPS 9700 LED 2800 RPM
    Corsair CM2X PC-6400 2X 1024MB http://www.corsair.com/_datasheets/CM2X1024-6400.pdf
    Kingston KHX6400 2x2048MB http://www.valueram.com/datasheets/KHX6400D2K2_4G.pdf
    Zotac GTS 250 1024GB DDR3
    Antec Nine hundred 2 case http://www.antec.com/Believe_it/product.php?id=NzIy
    PSU Antec Truepower series TP650 http://www.antec.com/Believe_it/product.php?id=MTc1OQ==
    DELL 20" Monitor

  6. #36
    Join Date
    Aug 2010
    Location
    Montreal
    Posts
    91

    Default Re: help overclocking Q6600 with GA-EP45 UD3L

    if i wanted to go to 3.4ghz i would up the vcore and FSB and DRam voltage and what else ?
    GA-EP45-UD3L REV 1.1 bios F9
    INTEL Core 1 Quad Q6600 2.4ghz to 3.2ghz
    Zalman CNPS 9700 LED 2800 RPM
    Corsair CM2X PC-6400 2X 1024MB http://www.corsair.com/_datasheets/CM2X1024-6400.pdf
    Kingston KHX6400 2x2048MB http://www.valueram.com/datasheets/KHX6400D2K2_4G.pdf
    Zotac GTS 250 1024GB DDR3
    Antec Nine hundred 2 case http://www.antec.com/Believe_it/product.php?id=NzIy
    PSU Antec Truepower series TP650 http://www.antec.com/Believe_it/product.php?id=MTc1OQ==
    DELL 20" Monitor

  7. #37
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: help overclocking Q6600 with GA-EP45 UD3L

    For 3.4GHz (378MHz FSB x 9) you will have to compromise memory frequency unless you are willing to overvolt it above specs.
    Another option is 425Mhz FSB x 8, which overclock the memory less.
    If you lower memory multiplier (2.00B or 2.00D) no need to increase DRAM Voltage.
    VTT(CPU Termination) 1.2-1.32v (maybe more)
    MCH Core 1.2-1.26v.
    CPU PLL 1.55-1.61v.

  8. #38
    Join Date
    Aug 2010
    Location
    Montreal
    Posts
    91

    Default Re: help overclocking Q6600 with GA-EP45 UD3L

    ok thanks so much your great help on this forum first i will wait for prime test to finish today 3 hours now running on blend no error yet tomorrow i will go for 3.4ghz that most i will go nothing more for sure. i did small fft for 1.5 hours and large fft for 1.5 hours now running blend for 3 hours no error yet will stop blend at about 8 hours from now and see.
    GA-EP45-UD3L REV 1.1 bios F9
    INTEL Core 1 Quad Q6600 2.4ghz to 3.2ghz
    Zalman CNPS 9700 LED 2800 RPM
    Corsair CM2X PC-6400 2X 1024MB http://www.corsair.com/_datasheets/CM2X1024-6400.pdf
    Kingston KHX6400 2x2048MB http://www.valueram.com/datasheets/KHX6400D2K2_4G.pdf
    Zotac GTS 250 1024GB DDR3
    Antec Nine hundred 2 case http://www.antec.com/Believe_it/product.php?id=NzIy
    PSU Antec Truepower series TP650 http://www.antec.com/Believe_it/product.php?id=MTc1OQ==
    DELL 20" Monitor

  9. #39
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: help overclocking Q6600 with GA-EP45 UD3L

    What are core temps during Prime95?
    Save BIOS profile (F11 in main BIOS screen) after you complete the stress test.

  10. #40
    Join Date
    Aug 2010
    Location
    Montreal
    Posts
    91

    Default Re: help overclocking Q6600 with GA-EP45 UD3L

    core 0 is 69 42 70
    core 1 62 39 68
    core 2 46 32 49
    core 3 46 33 50
    GA-EP45-UD3L REV 1.1 bios F9
    INTEL Core 1 Quad Q6600 2.4ghz to 3.2ghz
    Zalman CNPS 9700 LED 2800 RPM
    Corsair CM2X PC-6400 2X 1024MB http://www.corsair.com/_datasheets/CM2X1024-6400.pdf
    Kingston KHX6400 2x2048MB http://www.valueram.com/datasheets/KHX6400D2K2_4G.pdf
    Zotac GTS 250 1024GB DDR3
    Antec Nine hundred 2 case http://www.antec.com/Believe_it/product.php?id=NzIy
    PSU Antec Truepower series TP650 http://www.antec.com/Believe_it/product.php?id=MTc1OQ==
    DELL 20" Monitor

Page 4 of 14 FirstFirst ... 23456 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •