Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

Thread: BIOS Settings




  1. #11
    Join Date
    Dec 2010
    Location
    Hawaii
    Posts
    10

    Default Re: BIOS Settings

    Have set up as you indicated but I dont know if it is stable. I will run prime95 in a minute. Least my computer started.
    MB: ASUS Crosshair IV Formula
    Proc: AMD Phenom II x6 1100T BE
    Mem: 8GB DDR3 Kingston Hyper X Genesis
    Vid: Dual HD 5770 in Crossfire

  2. #12
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

  3. #13
    Join Date
    Dec 2010
    Location
    Hawaii
    Posts
    10

    Default Re: BIOS Settings

    Ran 10 minutes on Prime 95 with no errors.
    MB: ASUS Crosshair IV Formula
    Proc: AMD Phenom II x6 1100T BE
    Mem: 8GB DDR3 Kingston Hyper X Genesis
    Vid: Dual HD 5770 in Crossfire

  4. #14
    Join Date
    Mar 2010
    Location
    Finland
    Posts
    167

    Default Re: BIOS Settings

    I believe that our memory kits use similar settings, mine just runs on lower voltage. To run your memory at full 1200 MHz these settings should work, this is so light overclock that even a stock cooler would probably work. Static tRead Value may need to be higher, my memory kit can run with 6.

    Code:
    ******Motherboard Intelligent Tweaker (M.I.T.)******
    
    Robust Graphics Booster.........................[ Auto      ]
    CPU Clock Ratio.................................[ 8         ]
    Fine CPU Clock Ratio............................[ + 0.5     ]
    CPU Frequency 3.18GHz...........................[ 375 x 8.5 ]
    
    ******Clock Chip Control******
    
    CPU Host Clock Control..........................[ Enabled ]
    CPU Host Frequency (Mhz)........................[ 375 ]
    PCI Express Frequency (Mhz).....................[ 100 ]
    C.I.A 2........................................ [Disabled]
    
    ******Advanced Clock Control******
    
    CPU Clock Drive.................................[ 800mv ]
    PCI Express Clock Drive.........................[ 900mv ]
    CPU Clock Skew..................................[  0ps ]
    MCH Clock Skew..................................[  0ps ]
    
    ******DRAM Performance Control******
    
    Performance Enhance.............................[Standard]
    Extreme Memory Profile..........................[Disabled]
    (G) MCH Frequency Latch.........................[ 333 MHz]
    System Memory Multipler.........................[ 3.20B  ]
    Memory Frequency 1066...........................[ 1200   ]
    DRAM Timing Selectable..........................[ Manual ]
    
    CAS Latency Time................................[ 5  ]
    tRCD............................................[ 5  ]
    tRP.............................................[ 5  ]
    tRAS............................................[ 15 ]
    
    ******Advanced Timing Control******
    
    tRRD............................................[ 4  ]
    tWTR............................................[ 4  ]
    tWR.............................................[ 8  ]
    tRFC............................................[ 68 ]
    tRTP............................................[ 4  ]
    Command Rate (cmd)..............................[ Auto ]
    
    ******Channel A Timing Settings******
    
    Static tRead Value  ...........................[ 6    ]
    tRD Phase0 Adjustment .........................[ Auto ]
    tRD Phase1 Adjustment  ........................[ Auto ]
    tRD Phase2 Adjustment  ........................[ Auto ]
    tRD Phase3 Adjustment  ........................[ Auto ]
    
    tRD 2rd (Differnt Rank)  ......................[ Auto ]
    tWR 2wr (Differnt Rank)  ......................[ Auto ]
    tWR 2rd (Differnt Rank)  ......................[ Auto ]
    tRD 2wr (Same/Difft Rank) .....................[ Auto ]
    
    Dimm 1 Clock Skew Control......................[ Auto ]
    Dimm 2 Clock Skew Control......................[ Auto ]
    DDR Write Training.............................[ Auto ]
    
    ******Channel A Driving Settings******
    
    Drive Strength Profile.........................[ OC-1200]
    Data Driving Pull Up Level.....................[ Auto   ]
    cmd Driving Pull Up Level......................[ Auto   ]
    ctrl Driving Pull Up Level.....................[ Auto   ]
    clk Driving Pull Up Level......................[ Auto   ]
    
    Data Driving Pull Down Level...................[ Auto   ]
    cmd Driving Pull Down Level....................[ Auto   ]
    ctrl Driving Pull Down Level...................[ Auto   ]
    clk Driving Pull Down Level....................[ Auto   ]
    
    ******Channel B Timing Settings******
    
    Static tRead Value  ...........................[ 6    ]
    tRD Phase0 Adjustment .........................[ Auto ]
    tRD Phase1 Adjustment  ........................[ Auto ]
    tRD Phase2 Adjustment  ........................[ Auto ]
    tRD Phase3 Adjustment  ........................[ Auto ]
    
    tRD 2rd (Differnt Rank)  ......................[ Auto ]
    tWR 2wr (Differnt Rank)  ......................[ Auto ]
    tWR 2rd (Differnt Rank)  ......................[ Auto ]
    tRD 2wr (Same/Difft Rank) .....................[ Auto ]
    
    Dimm 1 Clock Skew Control......................[ Auto ]
    Dimm 2 Clock Skew Control......................[ Auto ]
    DDR Write Training.............................[ Auto ]
    
    ******Channel B Driving Settings******
    
    Drive Strength Profile.........................[ OC-1200]
    Data Driving Pull Up Level.....................[ Auto   ]
    cmd Driving Pull Up Level......................[ Auto   ]
    ctrl Driving Pull Up Level.....................[ Auto   ]
    clk Driving Pull Up Level......................[ Auto   ]
    
    Data Driving Pull Down Level...................[ Auto   ]
    cmd Driving Pull Down Level....................[ Auto   ]
    ctrl Driving Pull Down Level...................[ Auto   ]
    clk Driving Pull Down Level....................[ Auto   ]
    
    ******Motherboard Voltage Control******
    
    Load-Line Calibration..........................[ Disabled]
    CPU Vcore [ 1.225].............................[ Normal  ]
    CPU Termination [ 1.20 ].......................[ Normal  ]
    CPU PLL [ 1.50 ]...............................[ Normal  ]
    CPU Reference [ 0.760 ]........................[ Normal  ]
    
    MCH Core [ 1.100 ].......................[ 1.300  ]
    MCH Reference [ 0.760 ]..................[ Normal ]
    MCH/DRAM Refernce [ 0.900 ]..............[ Normal ]
    ICH I/O [ 1.500 ]........................[ Normal ]
    ICH Core [ 1.100 ].......................[ Normal ]
    
    DRAM Voltage [ 1.800 ]...................[ 2.10   ]
    DRAM Termination [ 0.900 ]...............[ Normal ]
    Channel A Ref [ 0.900 ]..................[ Normal ]
    Channel B Ref [ 0.900 ]..................[ Normal ]
    
    Advanced Settings
    Limit CPUID Max. to 3 ...................[ Disabled ]
    No-Execute Memory Protect ...............[ Enabled  ]
    CPU Enhanced Halt (C1E) .................[ Disabled ]
    C2/C2E State Support ....................[ Disabled ]
    x C4/C4E State Support ..................[ Disabled ]
    CPU Thermal Monitor 2 (TM2) .............[ Enabled  ]
    CPU EIST Function .......................[ Disabled ]
    Virtualization Technology ...............[ Enabled  ]
    
    Integrated Peripherals
    Legacy USB Storage Detect ...............[ Enabled ]
    Memory performance with these settings:
    Gigabyte GA-Z68XP-UD4
    i7-2600K @ 4.5 GHz, EK Supreme HF
    Kingston HyperX Genesis PC3-12800 2* 4 GB
    Radeon HD 7950
    OCZ Agility 3 120 GB
    XFX 650W Core edition
    Fractal Design Arc Midi

    Gigabyte GA-Z77X-UDH5
    i7-3770K @ 4.5 GHz, XSPC Raystorm
    G.Skill Ripjaws X 2* 4 GB
    Radeon HD 6870 * 2
    PNY XL8 120 GB
    Super Flower SF-700P14XE
    Bitfenix Shinobi XL

  5. #15
    Join Date
    Dec 2010
    Location
    Hawaii
    Posts
    10

    Unhappy Re: BIOS Settings

    This is where I currently stand with this issue. I have followed LSDmeasap's advice and set up my bios accordingly. I have booted up and been stable long enough to install drivers and update windows. I have a problem with some applications hanging though. On the initial it looks like it is working right but when I installed BFBC2 last night and tried to go online, the online server list never refreshed. I exited out and verified my net connection and ran a speed test to www.speedtest.net and got flying colors there. If I had to guess there may be something still wrong with board The computer is just not performing as well as it used to and I am inclined to look for another board. It just hard to find another LGA775 that supports DDR2 and has two PCIe slots.

    WCCRayzor
    MB: ASUS Crosshair IV Formula
    Proc: AMD Phenom II x6 1100T BE
    Mem: 8GB DDR3 Kingston Hyper X Genesis
    Vid: Dual HD 5770 in Crossfire

  6. #16
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: BIOS Settings

    Is it the game only that gives you issues? If so then it may be the game itself.

    Are you installing the latest drivers, not what is on the CD?

Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •