Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 7 of 7 FirstFirst ... 567
Results 61 to 68 of 68

Thread: Kingston HyperX T1 Series 6GB




  1. #61
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: Kingston HyperX T1 Series 6GB

    Oh I thought you had a new OCZ kit.

    Your memory is probably capable of 8-8-8-24 timings at 1600, and 7-7-7-21 at 1333 (current frequency,) with voltage set to 1.65v.

  2. #62
    Join Date
    Jan 2011
    Location
    There
    Posts
    32

    Default Re: Kingston HyperX T1 Series 6GB

    I have never played around with that side of computers. I think since I bought the wrong kind of memory, I should try to over clock it;)

  3. #63
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: Kingston HyperX T1 Series 6GB

    Yes at least tighten the timings, it would be a shame to run them at 1333 C9.

  4. #64
    Join Date
    Jan 2011
    Location
    There
    Posts
    32

    Default Re: Kingston HyperX T1 Series 6GB

    And thats something I have to play with in the bios right?

  5. #65
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: Kingston HyperX T1 Series 6GB

    Yes, not a lot though. Just a few changes. I have never been in personal contact with AMD board BIOS but it looks the following are the only changes u need to make for the current 1333 frequency.
    Code:
    DRAM	Confguration    [Press Enter] <<< enter here to change timings
    ********   System Voltage Optimized    ******** 
    System Voltage Control____[Manual]
    DRAM Voltage Control______1.65 (1.64/1.66)
    
    DRAM Configuration
    DDR3 Timing Items  [Manual]
    CAS# latency_______________7
    RAS to CAS R/W Delay_______7
    Row Precharge Time_________7
    Minimum RAS Active Time___21
    Tese are in the M.I.T (MB Inteligent tweaker)

  6. #66
    Join Date
    Apr 2009
    Location
    Virginia
    Posts
    1,470

    Default Re: Kingston HyperX T1 Series 6GB

    I can try to help with changeing the timings. Click delete key at first beep to enter bios. Then navigate to MB Intelligent Tweaker(M.I.T.). I would like to suggest first turn up the memory voltage a little.
    Below shows some changes you may want to try.
    Code:
    MB Intelligent Tweaker(M.I.T.)
    CPU Clock Ratio [Auto] 2800Mhz
    CPU NorthBridge Freq. [Auto] 2000Mhz
    CPU Host Clock Control [Auto]
    x CPU Frequency(MHz) 200
    PCIE Clock(MHz) [Auto]
    HT Link Frequency [Auto]
    Set Memory Clock [Auto]
    x Memory Clock x6.66 1333Mhz
    } DRAM Configuration [Press Enter]
    ******** System Voltage Optimized ********
    System Voltage Control [Auto]
    x DRAM Voltage Control Manual +0.15
    x NB Voltage Control Auto
    x NB PCIE Voltage Control Auto
    x CPU NB VID Control Auto
    x CPU Voltage Control Auto
    Normal CPU Vcore 1.3250V
    I would set voltage up a little first then save and exit reboot press delete back into bios.
    Then navigate to MB Intelligent Tweaker(M.I.T.) again.
    Code:
    MB Intelligent Tweaker(M.I.T.)
    CPU Clock Ratio [Auto] 2800Mhz
    CPU NorthBridge Freq. [Auto] 2000Mhz
    CPU Host Clock Control [Auto]
    x CPU Frequency(MHz) 200
    PCIE Clock(MHz) [Auto]
    HT Link Frequency [Auto]
    Set Memory Clock [Auto]
    x Memory Clock x6.66 1333Mhz
    } DRAM Configuration [Press Enter]
    ******** System Voltage Optimized ********
    System Voltage Control [Auto]
    x DRAM Voltage Control +0.15v=1.65v
    x NB Voltage Control Auto
    x NB PCIE Voltage Control Auto
    x CPU NB VID Control Auto
    x CPU Voltage Control Auto
    Normal CPU Vcore 1.3250V
    Code:
    DRAM Configuration
    DCTs Mode [Unganged]
    DDR3 Timing Items [Manual] SPD Auto
    x CAS# latency 7T 7T 7T
    x RAS to CAS R/W Delay 7T 7T 7T
    x Row Precharge Time 7T 7T 7T
    x Minimum RAS Active Time 21T 30T 30T
    x 1T/2T Command Timing Auto -- --
    x TwTr Command Delay Auto 5T 5T
    x Trfc0 for DIMM1 Auto 90ns 90ns
    x Trfc2 for DIMM2 Auto -- --
    x Trfc1 for DIMM3 Auto -- --
    x Trfc3 for DIMM4 Auto -- --
    x Write Recovery Time Auto 10T 10T
    x Precharge Time Auto 5T 5T
    x Row Cycle Time 28T 28T 28T
    x RAS to RAS Delay Auto 4T 4T
    Bank interleaving [Enabled]
    Channel interleave [Enabled]
    Save and Exit. Try these and let us see some new memory bench marks to compare with please. We seen some of your old ones at 9-9-9-24 "Thanks".
    Last edited by artdrivers; 01-20-2011 at 09:00 AM.
    http://forums.tweaktown.com/gigabyte...ench-test.html
    http://www.gigabyte-usa.com/FileList...ios_qflash.pdf
    Phenom II 945 @ 3.2Ghz w/Thermaltake Big Typhoon Pro 14 CPU Cooler
    Gigabyte GA-MA78GM-S2H rev.1.1 F11
    Sapphire 3870HD / 100225L / 512MB / ddr4
    4GB / Kingston / KHX8500D2K2/2GN / 5-5-5-18 / 1066Mhz
    (2) WD Caviar / WD2500AAKS/ 250GB in SATA RAID-0
    (1) WD Caviar / WD2500AAKS/ 250GB in SATA AHCI
    (2) IDE's 1 8XdualDVDRW 1 52x32x52x CDRW
    Antec /Neo HE550 / 550W
    Mid size ATX case with show through panel
    2) 80x80 front fans (1) 120x120 rear fan and small nb fan
    Microsoft comfort curve USB keyboard 2000 ver.1.0
    Logitech G500 USB mouse
    Monitor: CMV937A
    7.1+2 Channel High Definition ALC889A
    Dual boot Windows 7 32bit home & Windows 7 64bit home


  7. #67
    Chike is offline Senior Member
    Join Date
    Jun 2009
    Location
    Israel
    Posts
    6,531

    Default Re: Kingston HyperX T1 Series 6GB

    @artdrivers
    The manual list "1.500V ~ 2.400V The adjustable range is from 1.500V to 2.400V.", not increment, is this new to AMD boards or how it was before?

  8. #68
    Join Date
    Apr 2009
    Location
    Virginia
    Posts
    1,470

    Default Re: Kingston HyperX T1 Series 6GB

    The manual list "1.500V ~ 2.400V The adjustable range is from 1.500V to 2.400V.", not increment, is this new to AMD boards or how it was before?
    That is the range.
    The memory should be defaulted close to 1.536v on auto. (but when you switch from auto to manual it starts at 1.5v or close to that. When you add +0.15v to 1.5v= 1.65v.
    The bios will allow voltage adjustments up to 2.4v in MB Intelligent Tweaker(M.I.T.). Please adjust voltage to 1.65v first.
    You can see what the memory voltage is in BIOS on the PC Health tab. After raising the increment. You must Save and exit to make the change. Then go back into Bios and go to PC Health Status to see what it is set to.
    Code:
    PC Health Status
    Hardware Thermal Control [Enabled]
    Reset Case Open Status [Disabled]
    Case Opened No
    Vcore 1.364V
    DDR3 1.65V to 1.66V is good
    +3.3V 3.280V
    +12V 12.048V
    Current System Temperature 38oC
    Current CPU Temperature 36oC
    Current CPU FAN Speed 1962 RPM
    Current SYSTEM FAN1 Speed 0 RPM
    Current SYSTEM FAN2 Speed 0 RPM
    Current POWER FAN Speed 0 RPM
    CPU Warning Temperature [Disabled]
    CPU FAN Fail Warning [Disabled]
    SYSTEM FAN1 Fail Warning [Disabled]
    SYSTEM FAN2 Fail Warning [Disabled]
    POWER FAN Fail Warning [Disabled]
    CPU Smart FAN Control [Enabled]
    CPU Smart FAN Mode [Auto]
    System Smart FAN Control [Enabled]
    Last edited by artdrivers; 01-21-2011 at 07:27 AM.
    http://forums.tweaktown.com/gigabyte...ench-test.html
    http://www.gigabyte-usa.com/FileList...ios_qflash.pdf
    Phenom II 945 @ 3.2Ghz w/Thermaltake Big Typhoon Pro 14 CPU Cooler
    Gigabyte GA-MA78GM-S2H rev.1.1 F11
    Sapphire 3870HD / 100225L / 512MB / ddr4
    4GB / Kingston / KHX8500D2K2/2GN / 5-5-5-18 / 1066Mhz
    (2) WD Caviar / WD2500AAKS/ 250GB in SATA RAID-0
    (1) WD Caviar / WD2500AAKS/ 250GB in SATA AHCI
    (2) IDE's 1 8XdualDVDRW 1 52x32x52x CDRW
    Antec /Neo HE550 / 550W
    Mid size ATX case with show through panel
    2) 80x80 front fans (1) 120x120 rear fan and small nb fan
    Microsoft comfort curve USB keyboard 2000 ver.1.0
    Logitech G500 USB mouse
    Monitor: CMV937A
    7.1+2 Channel High Definition ALC889A
    Dual boot Windows 7 32bit home & Windows 7 64bit home


Page 7 of 7 FirstFirst ... 567

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •