Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 1 of 2 12 LastLast
Results 1 to 10 of 15

Thread: GA-X58A-UD3R rev. 2.0 Cold Boot Issues




  1. #1
    Join Date
    Nov 2011
    Location
    UK
    Posts
    7

    Default GA-X58A-UD3R rev. 2.0 Cold Boot Issues

    Hi,

    I have a self built PC based around the GA-X58A-UD3R rev. 2.0 board. I'm experiencing ongoing cold boot issues where each morning it will take up to 8 reboots to get windows 7 Ultimate to load. Once loaded its then as solid as a rock for the rest of the day - if I leave the system on its fine (I can reboot and it loads a-ok) but if I turn it off and go to a meeting for longer than an hour or two then the cold boot issue resurfaces.

    I receive a number of error messages relating to:

    ntdll.dll
    various memory isses
    various stop codes starting 0x...

    Going through windows start up recovery once it finally loads without errors then means the system will reboot and load windows correctly on the next attempt. This process takes 10 to 15minutes to go from first powering up to actually being able to use the system.

    I've run a mem test on the RAM both as a group and then each of the six stick individually. These tests ran for over 3 hours per memtest and reported zero errors. I take this as indicating the RAM is a-ok.

    BIOS reports the RAM in full correctly and windows does too.

    Here are my System/Bios specs -I'm currently using the XMP Profile1 as recommended in the motherboard manual.

    Code:
    CPU = Model Intel i7-950 3.06Ghz
    Motherboard = GA-X58A-UD3R rev. 2.0
    BIOS Version = FG
    Ram = 2 x 6GB Corsair Dominator (3x2GB) DDR3 PC3-12800C8 1600MHz Triple Channel Kit - CMP6GX3M3A1600C8
    Ram = 1600MHz RAM Speed, CAS 8-8-8-24 Timings, 1.6-1.7v VDIMM
    Ram = Total 12GB in Machine
    PSU = OCW 600W ModXStream PRO Modular
    GFX = Sapphire ATI Radeon HD 5770 FLEX 1024MB GDDR5 PCI-Express
    
    
    Advanced CPU Features:
    CPU Clock Ratio ................................ [23x]
    Intel(R) Turbo Boost Tech .................. [Auto]
    CPU Cores Enabled ............................ [All]
    CPU Multi Threading .......................... [Enabled]
    CPU Enhanced Halt (C1E) ................... [Auto]
    C3/C6/C7 State Support .................... [Disabled]
    CPU Thermal Monitor ......................... [Auto]
    CPU EIST Function ............................ [Auto]
    Virtualization Technology ................... [Enabled]
    Bi-Directional PROCHOT ..................... [Auto]
    
    
    Uncore & QPI Features:
    QPI Clock Ratio.............................. [Auto]
    QPI Link Speed .............................. 4.8Ghtz
    Uncore CloCk Ratio .......................... [Auto]
    Uncore Frequency ............................ 3200Mhz
    Isonchronous Frequency ..................[Enabled]
    
    
    Standard Clock Control:
    Base Clock (BCLK) Control ................ [Disabled]
    BCLK Frequency (MHz) ..................... [133]
    Extreme Memory Profile (X.M.P) ........... [Profile1]
    System Memory Multiplier ................. [Auto]
    Memory Frequency ......................... 1600
    PCI Express Frequency (MHz) ........... [Auto]
    
    
    Advanced Clock Control:
    CPU Clock Drive ..............................[700mV]
    PCI Express Clock Drive ................... [700mV]
    CPU Clock Skew ............................. [0ps]
    IOH Clock Skew ............................. [0ps]
    
    
    Advanced DRAM Features:
    Performance Enhance ...................... [Turbo]
    Extreme Memory Profile (X.M.P) ......... [Profile1]
    System Memory Multiplier (SPD) ........ [Auto]
    DRAM Timing Selectable (SPD) .......... [Auto]
    Profile DDR Voltage ................... 1.65V
    profile QPI Voltage ................... 1.2V
    X Channel Interleaving ................ 6 Auto
    X Rank Interleaving ................... 4 Auto
    
    
    Channel A + B + C
    
    Channel A Timing Settings:
    ##Channel A Standard Timing Control##
    CAS Latency Time ........................... 8 Auto
    tRCD ....................................... 8 Auto
    tRP ........................................ 8 Auto
    tRAS ....................................... 24 Auto
    
    
    ##Channel A Advanced Timing Control##
    tRC ........................................ 41 Auto
    tRRD ....................................... 6 Auto
    tWTR ......................................  6 Auto
    tWR ........................................ 12 Auto
    tWTP ....................................... 24 Auto
    tWL ........................................ 8 Auto
    tRFC ....................................... 88 Auto
    tRTP ....................................... 6 Auto
    tFAW ....................................... 30 Auto
    Command Rate (CMD) ......................... 2 Auto
    
    ##Channel A Misc Timing Control##
    Round Trip Latency .................... 56 Auto
    B2B CAS Delay .......................... [- Auto]
    
    
    Advanced Voltage Control:
    
    CPU
    Load Line Calibration ................. [Auto]
    CPU Vcore ............................. 1.26875V [Auto]
    QPI/VTT Voltage ....................... 1.175V [Auto]
    CPU PLL ............................... 1.800V [Auto]
    
    MCH/ICH
    PCIE 1.500v .......................... [Auto]
    QPI PLL 1.100v ....................... [Auto]
    IOH Core 1.100v ...................... [Auto]
    ICH I/O 1.500v ....................... [Auto]
    ICH Core 1.100v ...................... [Auto]
    
    DRAM
    DRAM Voltage 1.500v .............. [Auto]
    DRAM Termination 0.750v .......... [AUTO]
    Ch-A Data VRef. 0.750v ........... [AUTO]
    Ch-B Data VRef. 0.750v ........... [AUTO]
    Ch-C Data VRef. 0.750v ........... [AUTO]
    Ch-A Address VRef. 0.750v ........ [AUTO]
    Ch-B Address VRef. 0.750v ........ [AUTO]
    Ch-C Address VRef. 0.750v ........ [AUTO]
    Any help with tweaking the settings to get a stable first loading system would be really appreciated.

    kind Regards,

    Geo.

  2. #2
    Join Date
    Feb 2011
    Location
    TW
    Posts
    149

    Default Re: GA-X58A-UD3R rev. 2.0 Cold Boot Issues

    You can try 1.7V RAM voltage or higher RAM timing

  3. #3
    Join Date
    Feb 2011
    Location
    TW
    Posts
    149

    Default Re: GA-X58A-UD3R rev. 2.0 Cold Boot Issues

    My friend has got the same issue and issue fixed after flashed to FH5 BIOS.
    You can get FH5 from this link: http://www.fileden.com/files/2009/12...8aud3r.fh5.zip

  4. #4
    Join Date
    Aug 2009
    Location
    Birmingham,Great Britain
    Posts
    9,250

    Default Re: GA-X58A-UD3R rev. 2.0 Cold Boot Issues

    try these settings,your qpi/vtt voltage isnt enough using xmp,could give you cold boot issues

    CPU Cores Enabled ............................ [All]
    CPU Multi Threading .......................... [Enabled]
    CPU Enhanced Halt (C1E) ................... [Auto]
    C3/C6/C7 State Support .................... [Disabled]
    CPU Thermal Monitor ......................... [Auto]
    CPU EIST Function ............................ [Auto]
    Virtualization Technology ................... [Enabled]
    Bi-Directional PROCHOT ..................... [Auto]


    Uncore & QPI Features:
    QPI Clock Ratio.............................. [Auto] could try 44x
    QPI Link Speed .............................. 4.8Ghtz
    Uncore CloCk Ratio .......................... [Auto]
    Uncore Frequency ............................ 3200Mhz or 20x
    Isonchronous Frequency ..................[Enabled]


    Standard Clock Control:
    Base Clock (BCLK) Control ................ [Disabled]
    BCLK Frequency (MHz) ..................... [133]
    Extreme Memory Profile (X.M.P) ........... [Profile1]
    System Memory Multiplier ................. [Auto] or 10x if not using xmp
    Memory Frequency ......................... 1600
    PCI Express Frequency (MHz) ........... [Auto]


    Advanced Clock Control:
    CPU Clock Drive ..............................[700mV] 800mv
    PCI Express Clock Drive ................... [700mV] 900mv
    CPU Clock Skew ............................. [0ps]
    IOH Clock Skew ............................. [0ps]


    Advanced DRAM Features:
    Performance Enhance ...................... [Turbo]
    Extreme Memory Profile (X.M.P) ......... [Profile1] could disable xmp and set ram manually
    System Memory Multiplier (SPD) ........ [Auto] 10x
    DRAM Timing Selectable (SPD) .......... [Auto] manual/quick
    Profile DDR Voltage ................... 1.65V
    profile QPI Voltage ................... 1.2V <<<<<< no where near enough for 12gb,set to atleast 1.38v
    X Channel Interleaving ................ 6 Auto
    X Rank Interleaving ................... 4 Auto


    Channel A + B + C

    Channel A Timing Settings:
    ##Channel A Standard Timing Control##
    CAS Latency Time ........................... 8 Auto type in 8
    tRCD ....................................... 8 Auto 8
    tRP ........................................ 8 Auto 8
    tRAS ....................................... 24 Auto 24


    ##Channel A Advanced Timing Control##
    tRC ........................................ 41 Auto
    tRRD ....................................... 6 Auto
    tWTR ...................................... 6 Auto
    tWR ........................................ 12 Auto
    tWTP ....................................... 24 Auto
    tWL ........................................ 8 Auto
    tRFC ....................................... 88 Auto
    tRTP ....................................... 6 Auto
    tFAW ....................................... 30 Auto
    Command Rate (CMD) ......................... 2 Auto

    ##Channel A Misc Timing Control##
    Round Trip Latency .................... 56 Auto
    B2B CAS Delay .......................... [- Auto]


    Advanced Voltage Control:

    CPU
    Load Line Calibration ................. [Auto]
    CPU Vcore ............................. 1.26875V [Auto]
    QPI/VTT Voltage ....................... 1.175V [Auto] set to above ^ atleast 1.38v
    CPU PLL ............................... 1.800V [Auto]

    MCH/ICH
    PCIE 1.500v .......................... [Auto]
    QPI PLL 1.100v ....................... [Auto]
    IOH Core 1.100v ...................... [Auto]
    ICH I/O 1.500v ....................... [Auto]
    ICH Core 1.100v ...................... [Auto]

    DRAM
    DRAM Voltage 1.500v .............. [Auto] set according to whats printed on your ram,either 1.5v or 1.66v
    DRAM Termination 0.750v .......... [AUTO]
    Ch-A Data VRef. 0.750v ........... [AUTO]
    Ch-B Data VRef. 0.750v ........... [AUTO]
    Ch-C Data VRef. 0.750v ........... [AUTO]
    Ch-A Address VRef. 0.750v ........ [AUTO]
    Ch-B Address VRef. 0.750v ........ [AUTO]
    Ch-C Address VRef. 0.750v ........ [AUTO]
    Gigabyte z77x UP4-TH F11c Modded Bios
    Intel i7 3770k 24/7@4.8ghz 1.38v Turbo llc +0.165v dvid multithreading enabled
    Samsung Green(MV-3V4G3D/US) 8GB @2133mhz 9-10-10-21-1t 1.55v
    Thermalright Silver Arrow Cpu Cooler
    1xSamsung 840 pro 256 Gb SSD windows 8.1 pro 64bit
    1xSamsung f4 HD204UI 2tb hard drive Storage
    Powercolor 7970 3gb V3 @1150mhz core/1700mhz mem,1.150v Accelero aftermarket air cooler 55c max
    Razer Lycosa Keyboard
    Logitech X-530 5.1 Speakers
    Lite-On iHAS124-19 24x Sata DVDRW
    K-World Hybrid DVB-T 210SE Digital T.V Card
    L.G E2260V L.E.D 1920x1080 Monitor
    Xfx Pro 750w silver rated Psu 80+
    Fractal Arc Midi Case

    http://i38.tinypic.com/14myvfa.jpg x58 ud5 <=3.8ghz + 4.2ghz Overclock Template!!
    http://www.youtube.com/user/warren304#p/u Visit Me On Youtube

    Lots Of Gaming Videos With X58 Ud5 System And Gpu On My Youtube Channel!!
    Just Uploaded New Battlefield 4 Video!!!!!!!!!!!!!!!!!!!!!!

  5. #5
    Join Date
    Nov 2011
    Location
    UK
    Posts
    7

    Default Re: GA-X58A-UD3R rev. 2.0 Cold Boot Issues

    Many thanks to you both :D

    Looks like thats fixed it. I upgraded the BIOS to FH5 and also set up the BIOS settings as Wazza stated and we've got a first time boot this morning from the system. Hopefully that should be the problem fixed.

    I'll keep the thread open for a few days and report back each day on the result of the cold boot so we can be certain its all fixed.

    Things have changed a lot BIOS/RAM wise in the 5ish years since my last build obviously - It all used to be plug and play back when I was building a system every couple of months for family or friends the hardest part always used to be crossing your fingers that the system would POST on the first power up! ;)

    Thanks again - I'll make sure I keep updating for a short while.

  6. #6
    Join Date
    Aug 2009
    Location
    Birmingham,Great Britain
    Posts
    9,250

    Default Re: GA-X58A-UD3R rev. 2.0 Cold Boot Issues

    you might be able to lower qpi/vtt voltage further,you would need to test but 1.35-1.38v would be the right area with 12gb of ram,you could also reduce your cpu voltage too if you wanted by using dvid
    Gigabyte z77x UP4-TH F11c Modded Bios
    Intel i7 3770k 24/7@4.8ghz 1.38v Turbo llc +0.165v dvid multithreading enabled
    Samsung Green(MV-3V4G3D/US) 8GB @2133mhz 9-10-10-21-1t 1.55v
    Thermalright Silver Arrow Cpu Cooler
    1xSamsung 840 pro 256 Gb SSD windows 8.1 pro 64bit
    1xSamsung f4 HD204UI 2tb hard drive Storage
    Powercolor 7970 3gb V3 @1150mhz core/1700mhz mem,1.150v Accelero aftermarket air cooler 55c max
    Razer Lycosa Keyboard
    Logitech X-530 5.1 Speakers
    Lite-On iHAS124-19 24x Sata DVDRW
    K-World Hybrid DVB-T 210SE Digital T.V Card
    L.G E2260V L.E.D 1920x1080 Monitor
    Xfx Pro 750w silver rated Psu 80+
    Fractal Arc Midi Case

    http://i38.tinypic.com/14myvfa.jpg x58 ud5 <=3.8ghz + 4.2ghz Overclock Template!!
    http://www.youtube.com/user/warren304#p/u Visit Me On Youtube

    Lots Of Gaming Videos With X58 Ud5 System And Gpu On My Youtube Channel!!
    Just Uploaded New Battlefield 4 Video!!!!!!!!!!!!!!!!!!!!!!

  7. #7
    Join Date
    Nov 2011
    Location
    UK
    Posts
    7

    Default Re: GA-X58A-UD3R rev. 2.0 Cold Boot Issues

    Darn it seems I celebrated a tad too soon - the cold boot issues have resurfaced this morning :(

    Here are my settings:

    CPU Cores Enabled ............................ [All]
    CPU Multi Threading .......................... [Enabled]
    CPU Enhanced Halt (C1E) ................... [Auto]
    C3/C6/C7 State Support .................... [Disabled]
    CPU Thermal Monitor ......................... [Auto]
    CPU EIST Function ............................ [Auto]
    Virtualization Technology ................... [Enabled]
    Bi-Directional PROCHOT ..................... [Auto]


    Uncore & QPI Features:
    QPI Clock Ratio.............................. [Auto]
    QPI Link Speed .............................. 4.8Ghtz
    Uncore CloCk Ratio .......................... [Auto]
    Uncore Frequency ............................ 20x
    Isonchronous Frequency ..................[Enabled]


    Standard Clock Control:
    Base Clock (BCLK) Control ................ [Disabled]
    BCLK Frequency (MHz) ..................... [133]
    Extreme Memory Profile (X.M.P) ........... [Disabled]
    System Memory Multiplier ................. 10x
    Memory Frequency ......................... 1600
    PCI Express Frequency (MHz) ........... [Auto]


    Advanced Clock Control:
    CPU Clock Drive .............................. 800mv
    PCI Express Clock Drive ................... 900mv
    CPU Clock Skew ............................. [0ps]
    IOH Clock Skew ............................. [0ps]


    Advanced DRAM Features:
    Performance Enhance ...................... [Turbo]
    Extreme Memory Profile (X.M.P) ......... [Disabled]
    System Memory Multiplier (SPD) ........ 10x
    DRAM Timing Selectable (SPD) .......... manual/quick
    Profile DDR Voltage ................... 1.65V
    profile QPI Voltage ................... 1.175V <<<<<< This doesn't seem to change despite what I set in the advanced control section...the option is greyed out as well
    X Channel Interleaving ................ Auto
    X Rank Interleaving ................... Auto


    Channel A + B + C

    Channel A Timing Settings:
    ##Channel A Standard Timing Control##
    CAS Latency Time ........................... 8
    tRCD ....................................... 8
    tRP ........................................ 8
    tRAS ....................................... 24


    ##Channel A Advanced Timing Control##
    tRC ........................................ Auto
    tRRD ....................................... Auto
    tWTR ...................................... Auto
    tWR ........................................ Auto
    tWTP ....................................... Auto
    tWL ........................................ Auto
    tRFC ....................................... Auto
    tRTP ....................................... Auto
    tFAW ....................................... Auto
    Command Rate (CMD) ......................... Auto

    ##Channel A Misc Timing Control##
    Round Trip Latency .................... Auto
    B2B CAS Delay .......................... [Auto]


    Advanced Voltage Control:

    CPU
    Load Line Calibration ................. [Auto]
    CPU Vcore ............................. [Auto]
    QPI/VTT Voltage ....................... 1.39V
    CPU PLL ............................... [Auto]

    MCH/ICH
    PCIE 1.500v .......................... [Auto]
    QPI PLL 1.100v ....................... [Auto]
    IOH Core 1.100v ...................... [Auto]
    ICH I/O 1.500v ....................... [Auto]
    ICH Core 1.100v ...................... [Auto]

    DRAM
    DRAM Voltage 1.500v .............. 1.660v
    DRAM Termination 0.750v .......... [AUTO]
    Ch-A Data VRef. 0.750v ........... [AUTO]
    Ch-B Data VRef. 0.750v ........... [AUTO]
    Ch-C Data VRef. 0.750v ........... [AUTO]
    Ch-A Address VRef. 0.750v ........ [AUTO]
    Ch-B Address VRef. 0.750v ........ [AUTO]
    Ch-C Address VRef. 0.750v ........ [AUTO]

  8. #8
    Join Date
    Aug 2009
    Location
    Birmingham,Great Britain
    Posts
    9,250

    Default Re: GA-X58A-UD3R rev. 2.0 Cold Boot Issues

    CPU Cores Enabled ............................ [All]
    CPU Multi Threading .......................... [Enabled]
    CPU Enhanced Halt (C1E) ................... [Auto]
    C3/C6/C7 State Support .................... [Disabled]
    CPU Thermal Monitor ......................... [Auto]
    CPU EIST Function ............................ [Auto]
    Virtualization Technology ................... [Enabled]
    Bi-Directional PROCHOT ..................... [Auto]


    Uncore & QPI Features:
    QPI Clock Ratio.............................. [Auto]
    QPI Link Speed .............................. 4.8Ghtz
    Uncore CloCk Ratio .......................... [Auto]
    Uncore Frequency ............................ 20x
    Isonchronous Frequency ..................[Enabled]


    Standard Clock Control:
    Base Clock (BCLK) Control ................ [Disabled]
    BCLK Frequency (MHz) ..................... [133]
    Extreme Memory Profile (X.M.P) ........... [Disabled]
    System Memory Multiplier ................. 10x
    Memory Frequency ......................... 1600
    PCI Express Frequency (MHz) ........... [Auto]


    Advanced Clock Control:
    CPU Clock Drive .............................. 800mv
    PCI Express Clock Drive ................... 900mv
    CPU Clock Skew ............................. [0ps]
    IOH Clock Skew ............................. [0ps]


    Advanced DRAM Features:
    Performance Enhance ...................... [Turbo] try with standard
    Extreme Memory Profile (X.M.P) ......... [Disabled]
    System Memory Multiplier (SPD) ........ 10x
    DRAM Timing Selectable (SPD) .......... manual/quick
    Profile DDR Voltage ................... 1.65V
    profile QPI Voltage ................... 1.175V
    X Channel Interleaving ................ Auto
    X Rank Interleaving ................... Auto


    Channel A + B + C

    Channel A Timing Settings:
    ##Channel A Standard Timing Control##
    CAS Latency Time ........................... 8
    tRCD ....................................... 8
    tRP ........................................ 8
    tRAS ....................................... 24


    ##Channel A Advanced Timing Control##
    tRC ........................................ Auto
    tRRD ....................................... Auto
    tWTR ...................................... Auto
    tWR ........................................ Auto
    tWTP ....................................... Auto
    tWL ........................................ Auto
    tRFC ....................................... Auto
    tRTP ....................................... Auto
    tFAW ....................................... Auto
    Command Rate (CMD) ......................... Auto

    ##Channel A Misc Timing Control##
    Round Trip Latency .................... Auto
    B2B CAS Delay .......................... [Auto]


    Advanced Voltage Control:

    CPU
    Load Line Calibration ................. [Auto]
    CPU Vcore ............................. [Auto]
    QPI/VTT Voltage ....................... 1.39V
    CPU PLL ............................... [Auto]

    MCH/ICH
    PCIE 1.500v .......................... [Auto]
    QPI PLL 1.100v ....................... [Auto]
    IOH Core 1.100v ...................... [Auto]
    ICH I/O 1.500v ....................... [Auto]
    ICH Core 1.100v ...................... [Auto]

    DRAM
    DRAM Voltage 1.500v .............. 1.660v
    DRAM Termination 0.750v .......... [AUTO]
    Ch-A Data VRef. 0.750v ........... [AUTO]
    Ch-B Data VRef. 0.750v ........... [AUTO]
    Ch-C Data VRef. 0.750v ........... [AUTO]
    Ch-A Address VRef. 0.750v ........ [AUTO]
    Ch-B Address VRef. 0.750v ........ [AUTO]
    Ch-C Address VRef. 0.750v ........ [AUTO]

    as long as xmp profile is disabled and you manually set qpi/vtt voltage then it wont matter about profile qpi being greyed out as its only enabled if xmp is used
    Gigabyte z77x UP4-TH F11c Modded Bios
    Intel i7 3770k 24/7@4.8ghz 1.38v Turbo llc +0.165v dvid multithreading enabled
    Samsung Green(MV-3V4G3D/US) 8GB @2133mhz 9-10-10-21-1t 1.55v
    Thermalright Silver Arrow Cpu Cooler
    1xSamsung 840 pro 256 Gb SSD windows 8.1 pro 64bit
    1xSamsung f4 HD204UI 2tb hard drive Storage
    Powercolor 7970 3gb V3 @1150mhz core/1700mhz mem,1.150v Accelero aftermarket air cooler 55c max
    Razer Lycosa Keyboard
    Logitech X-530 5.1 Speakers
    Lite-On iHAS124-19 24x Sata DVDRW
    K-World Hybrid DVB-T 210SE Digital T.V Card
    L.G E2260V L.E.D 1920x1080 Monitor
    Xfx Pro 750w silver rated Psu 80+
    Fractal Arc Midi Case

    http://i38.tinypic.com/14myvfa.jpg x58 ud5 <=3.8ghz + 4.2ghz Overclock Template!!
    http://www.youtube.com/user/warren304#p/u Visit Me On Youtube

    Lots Of Gaming Videos With X58 Ud5 System And Gpu On My Youtube Channel!!
    Just Uploaded New Battlefield 4 Video!!!!!!!!!!!!!!!!!!!!!!

  9. #9
    Join Date
    Nov 2011
    Location
    UK
    Posts
    7

    Default Re: GA-X58A-UD3R rev. 2.0 Cold Boot Issues

    Thanks for the reply. Sadly changing the Performance Enhance Turbo setting to Standard still hasn't fixed the problem.

    I tried upping the QPI voltage to the next setting and the board reported that the voltage was too high on post and automatically reset it back to 1.375v.

    Do you think theres anything else I could try?

    Thanks for your support.

    Geo.

  10. #10
    Join Date
    Nov 2011
    Location
    UK
    Posts
    7

    Default Re: GA-X58A-UD3R rev. 2.0 Cold Boot Issues

    Hi Again,

    Right full reinstall and still getting the same problems.

    I've discovered that if I switch the computer on, immediately hit delete to get into bios and leave the machine for about 10 minutes (go make a cup of tea and open the days post) and then boot the machine it works first time everytime with no errors or issues.

    Any ideas on what might be causing it? The computer is in my studio which is separate from the hosue and can get a bit colder over night, especially at this time of year.

    Is it likely to be happier booting once the power has circulated for a while? Does Ram or the CPU suffer from the slight chill?

    Is it possible that I've got a motherboard I need to RMA as its got some weird quirk?

    Kind regards,

    Geo.

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •