Ahh ok, well I wasn't sure what he wanted eventually, his post is kind of confusing

@ Maser, do the above mentioned! If you are starting with Fail Safe that is bad, so be sure you load Optimized Defaults, then save/apply/reboot BACK to the BIOS. Once in the BIOS again set your SATA Settings to what you need for windows, and ram voltage or any other important settings to you (But not overclock yet) then save/apply/reboot to windows. Then reboot and get back trying your overclock.

Try these setting changes from your above given ones.

Code:
Advanced CPU Features: CPU Clock Ratio ................................ [21x]
Intel(R) Turbo Boost Tech .................. [Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Disabled]
Bi-Directional PROCHOT ..................... [Disabled]

Uncore & QPI Features:
QPI Link Speed .............................. Slow mode << Set x36 (only 7.3GT/s, this if fine, and anything up towards 8GT/s should be too)
Uncore Frequency .......................... Set x16 or above for x6 memory multiplier, at these speeds using x12-x15 might be too slow, optimial uncore speed is 3.2/3.4 - 3.6+
Isonchronous Frequency ..................[Enabled]

Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... [205]
PCI Express Frequency (MHz) ........... [101]
C.I.A.2 [Disabled]

Advanced Clock Control:
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [900mV] << DO NOT manually change, if you do as instructed above with Optimized it will be set properly
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]

Advanced DRAM Features:
Performance Enhance ...................... [Standard]  << Extreme may be best!  I've ALWAYS used it, even at 2.8Ghz memory speeds
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [6.0]  << x8 may help, if you do that set Uncore above to x16-18
DRAM Timing Selectable (SPD) .......... [Manual]

Channel A + B + C Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ...................... [8]
tRCD ....................................... [8]
tRP ......................................... [8]
tRAS ....................................... [24]

Advanced Voltage Control:

CPU
Load Line Calibration ................. [Disabled]
CPU Vcore ............................... [1.3500] -1.45+ All depends on your CPU
QPI/VTT Voltage 1.150v ............[1.3000] - 1.45+  << Higher Uncore, QPI, Tight Memory, High Memory, all require higher voltages here, and what your CPU likes too, some need a lot others don't.   
CPU PLL 1.800v .......................[1.8800]  << Lower, higher does not help X58 really.   Set 1.4-1.7

MCH/ICH
PCIE 1.500v ...........................[1.5000]
QPI PLL 1.100v .......................[1.1000] << 1.20
IOH Core 1.100v .....................[1.1200] Stock/Auto -1.14 should be plenty, higher can cause errors often, NB Gets HOT
ICH I/O 1.500v .......................[1.5000]
ICH Core 1.1v ........................[1.1000]  << 1.14

DRAM
DRAM Voltage 1.500v .............. [1.6400]-1.68
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]