Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 25 of 74 FirstFirst ... 15232425262735 ... LastLast
Results 241 to 250 of 738

Thread: Socket 771 Mod Xeon X5460 GA-P35-DS3L Overclock




  1. #241
    lukevega is offline Member
    Join Date
    Apr 2014
    Location
    Newcastle upon Tyne, England
    Posts
    307

    Exclamation Re: Socket 771 Mod Xeon X5460 GA-P35-DS3L Overclock

    The system just cold booted twice...

    The BIOS settings were:

    Code:
    Motherboard: Gigabyte GA-P35-DS3L Rev 2.0: BIOS Version: F9C
    CPU: Intel Xeon X5460
    RAM: Kingston Model: 4x2GB HyperX T1 DDR2-1066 CL5 Part#: KHX8500D2T1K2/4G (http://www.kingston.com/datasheets/KHX8500D2T1K2_4G.pdf)
    Power Supply Unit: Corsair HX520W
    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio __________________ [9]
    Fine Clock Ratio __________________[0]
    CPU Host Clock Control____________[Enabled]
    CPU Host Frequency (MHz)_________[401]
    PCI Express Frequency (Mhz)________[101]
    C.I.A. 2__________________________[Disabled]
    Performance Enhance = ____________[Standard]
    System Memory Multiplier (SPD)_____[2.00]
    DRAM Timing Selectable_____ SPD ___[Manual]
     
    CAS Latency Time_______________5_[5]
    Dram RAS# to CAS# Delay________5_[5]
    Dram RAS# Precharge Delay_______5_[5]
    Precharge Delay (tRAS)__________18_[18]
     
    ACT to ACT Delay (tRRD)_________3_[Auto]
    Rank Write to READ Delay________3_[Auto]
    Write to Precharge Delay_________6_[Auto]
    Refresh to ACT Delay____________52_[Auto]
    Read to Precharge Delay__________3_[Auto]
    Static tRead Value_______________7_[7]
    Static tRead Phase Adjust_________0_[Auto]
     
    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [+0.1V]
    PCI-E OverVoltage Control_ [+0.1V]
    FSB OverVoltage Control___ [+0.1V]
    (G)MCH OverVoltage Control [+0.1V]
    CPU Voltage Control_______ [1.29375V]
    Normal CPU Vcore________1.23750V
    
    Hard Disk Boot Priority.....: [Press Enter]
    1.	Kingston SV300S37A240G
    2.	ST3500320AS
    3.	ST3500320AS
    First Boot Device...........: [Hard Disk]
    Second Boot Device......: [CDROM]
    Third Boot Device.........: [Disabled]
    Password Check...........: [Setup]
    HDD S.M.A.R.T. Capability......: [Disabled]
    Limit CPUID Max. to 3.........: [Disabled]
    No-Execute Memory Protect.........: [Enabled]
    CPU Enhanced Halt (C1E)...........: [Disabled]
    CPU Thermal Monitor 2(TM2) ......: [Enabled]
    CPU EIST Function...............: [Disabled]
    Virtualization Technology..........: [Disabled]
    Full Screen LOGO Show.........: [Disabled]
    Init Display First............: [PEG]
    
    SATA AHCI Mode.........: [AHCI]
    SATA Port0-1 Native Mode.........: [Enabled]
    USB Controller...........: [Enabled]
    USB 2.0 Controller............: [Enabled]
    USB Keyboard Support............: [Disabled]
    USB Mouse Support..........: [Disabled]
    Legacy USB Storage Detect…….[Disabled]
    Azalia Codec............: [Auto]
    Onboard H/W LAN............: [Enabled]
    SMART LAN.................: [Press Enter]
    Onboard LAN Boot ROM.......: [Disabled]
    Onboard IDE Controller........: [Enabled]
    Onboard Serial Port 1..........: [3F8/IRQ4]
    Onboard Parallel Serial Port...: [378/IRQ7]
    Parallel Port Mode................: [SPP]
    
    
    ACP1 Suspend Type........: [S3 (STR)]
    Soft-Off by PWR-BTTN....: [Delay 4 Sec.]
    PME Event Wake Up.......: [Disabled]
    Power On by Ring.......: [Disabled]
    Resume by Alarm......: [Disabled]
    HPET Support..........: [Enabled]
    HPET Mode.............: [64-bit mode]
    Power On by Mouse.............: [Double Click]
    Power On by Keyboard.........: [Disabled]
    AC Back Function..................: [Soft-Off]
    
    
    PCI1 IRQ Assignment.............: [Auto]
    PCI2 IRQ Assignment.............: [Auto]
    PCI3 IRQ Assignment............: [Auto]
    
    Reset Case Open Status...........: [Disabled]
    CPU Warning Temperature.......: [80°C/176°F]
    CPU FAN Fail Warning...............: [Disabled]
    SYSTEM FAN2 Fail Warning.......: [Disabled]
    POWER FAN Fail Warning..........: [Disabled]
    SYSTEM FAN1 Fail Warning.......: [Disabled]
    CPU Smart FAN Control.............: [Disabled]
    Do you think I need to increase the DDR2 OverVoltage Control to +0.2V? or perhaps increase Static tRead Value to 8? My final guess would be to increase the vcore... What do you think?
    GA-EP45-UD3P 1.0, Intel Xeon X5470, 4x2GB Kingston HyperX DDR2 1066, NVidia Geforce 8800GTS 512, Kingston V300 240GB, Noctua NH-U12P with 2x Noctua NF-P12 Push-Pull, Corsair HX520W, Antec P182, Windows 7 64-bit

  2. #242
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Socket 771 Mod Xeon X5460 GA-P35-DS3L Overclock

    Not so fast hotshot.

    I suggest that you use 9 x 390MHz = 3.510GHz with your 5-5-5-18 memory settings with dram voltage = 1.90 volts.

    Adjust your cpu vcore up as needed.

    From post #235, it looks like you have already set ACP1 Suspend Type = S3 (STR), double check this setting.

    If you really want to jump to 3.60GHz, that's up to you.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  3. #243
    lukevega is offline Member
    Join Date
    Apr 2014
    Location
    Newcastle upon Tyne, England
    Posts
    307

    Default Re: Socket 771 Mod Xeon X5460 GA-P35-DS3L Overclock

    I was just about to say that I tried all of the methods I listed and the only one that worked was increasing the Static tRead Value to 8.

    I will go back and adjust to the settings you recommend and report back!
    GA-EP45-UD3P 1.0, Intel Xeon X5470, 4x2GB Kingston HyperX DDR2 1066, NVidia Geforce 8800GTS 512, Kingston V300 240GB, Noctua NH-U12P with 2x Noctua NF-P12 Push-Pull, Corsair HX520W, Antec P182, Windows 7 64-bit

  4. #244
    lukevega is offline Member
    Join Date
    Apr 2014
    Location
    Newcastle upon Tyne, England
    Posts
    307

    Exclamation Re: Socket 771 Mod Xeon X5460 GA-P35-DS3L Overclock

    Ok, about to load these BIOS settings:

    Code:
    Motherboard: Gigabyte GA-P35-DS3L Rev 2.0: BIOS Version: F9C
    CPU: Intel Xeon X5460
    RAM: Kingston Model: 4x2GB HyperX T1 DDR2-1066 CL5 Part#: KHX8500D2T1K2/4G (http://www.kingston.com/datasheets/KHX8500D2T1K2_4G.pdf)
    Power Supply Unit: Corsair HX520W
    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio __________________ [9]
    Fine Clock Ratio __________________[0]
    CPU Host Clock Control____________[Enabled]
    CPU Host Frequency (MHz)_________[390]
    PCI Express Frequency (Mhz)________[101]
    C.I.A. 2__________________________[Disabled]
    Performance Enhance = ____________[Standard]
    System Memory Multiplier (SPD)_____[2.00]
    DRAM Timing Selectable_____ SPD ___[Manual]
     
    CAS Latency Time_______________5_[5]
    Dram RAS# to CAS# Delay________5_[5]
    Dram RAS# Precharge Delay_______5_[5]
    Precharge Delay (tRAS)__________18_[18]
     
    ACT to ACT Delay (tRRD)_________3_[Auto]
    Rank Write to READ Delay________3_[Auto]
    Write to Precharge Delay_________6_[Auto]
    Refresh to ACT Delay____________52_[Auto]
    Read to Precharge Delay__________3_[Auto]
    Static tRead Value_______________7_[7]
    Static tRead Phase Adjust_________0_[Auto]
     
    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [+0.1V]
    PCI-E OverVoltage Control_ [+0.1V]
    FSB OverVoltage Control___ [+0.1V]
    (G)MCH OverVoltage Control [+0.1V]
    CPU Voltage Control_______ [1.29375V]
    Normal CPU Vcore________1.23750V
    
    Hard Disk Boot Priority.....: [Press Enter]
    1.	Kingston SV300S37A240G
    2.	ST3500320AS
    3.	ST3500320AS
    First Boot Device...........: [Hard Disk]
    Second Boot Device......: [CDROM]
    Third Boot Device.........: [Disabled]
    Boot Up Floppy Seek.....: [Disabled]
    Password Check...........: [Setup]
    HDD S.M.A.R.T. Capability......: [Disabled]
    Limit CPUID Max. to 3.........: [Disabled]
    No-Execute Memory Protect.........: [Enabled]
    CPU Enhanced Halt (C1E)...........: [Disabled]
    CPU Thermal Monitor 2(TM2) ......: [Enabled]
    CPU EIST Function...............: [Disabled]
    Virtualization Technology..........: [Disabled]
    Full Screen LOGO Show.........: [Disabled]
    Init Display First............: [PEG]
    
    SATA AHCI Mode.........: [AHCI]
    SATA Port0-1 Native Mode.........: [Enabled]
    USB Controller...........: [Enabled]
    USB 2.0 Controller............: [Enabled]
    USB Keyboard Support............: [Disabled]
    USB Mouse Support..........: [Disabled]
    Legacy USB Storage Detect…….[Disabled]
    Azalia Codec............: [Auto]
    Onboard H/W LAN............: [Enabled]
    SMART LAN.................: [Press Enter]
    Onboard LAN Boot ROM.......: [Disabled]
    Onboard IDE Controller........: [Enabled]
    Onboard Serial Port 1..........: [3F8/IRQ4]
    Onboard Parallel Serial Port...: [378/IRQ7]
    Parallel Port Mode................: [SPP]
    
    ACP1 Suspend Type........: [S3(STR)]
    USB Device Wake-Up From S3..: [Disabled]
    Soft-Off by PWR-BTTN....: [Delay 4 Sec.]
    PME Event Wake Up.......: [Disabled]
    Power On by Ring.......: [Disabled]
    Resume by Alarm......: [Disabled]
    HPET Support..........: [Enabled]
    HPET Mode.............: [64-bit mode]
    Power On by Mouse.............: [Double Click]
    Power On by Keyboard.........: [Disabled]
    AC Back Function..................: [Soft-Off]
    
    Resources Controlled By.......[Auto]
    x IRQ Resources           Press Enter
    PCI Latency Timer (CLK)......: [32]
    PCI1 IRQ Assignment.............: [Auto]
    PCI2 IRQ Assignment.............: [Auto]
    PCI3 IRQ Assignment............: [Auto]
    
    Reset Case Open Status...........: [Disabled]
    CPU Warning Temperature.......: [80°C/176°F]
    CPU FAN Fail Warning...............: [Disabled]
    SYSTEM FAN2 Fail Warning.......: [Disabled]
    POWER FAN Fail Warning..........: [Disabled]
    SYSTEM FAN1 Fail Warning.......: [Disabled]
    CPU Smart FAN Control.............: [Disabled]
    I added a few settings which for some reason I had not been previously recording so I would ask if you could kindly scan through the above settings to see if any of the newly added settings are out of place.

    If these settings cold boot then I will slowly increase the vcore and try again.
    GA-EP45-UD3P 1.0, Intel Xeon X5470, 4x2GB Kingston HyperX DDR2 1066, NVidia Geforce 8800GTS 512, Kingston V300 240GB, Noctua NH-U12P with 2x Noctua NF-P12 Push-Pull, Corsair HX520W, Antec P182, Windows 7 64-bit

  5. #245
    lukevega is offline Member
    Join Date
    Apr 2014
    Location
    Newcastle upon Tyne, England
    Posts
    307

    Default Re: Socket 771 Mod Xeon X5460 GA-P35-DS3L Overclock

    I think the system is failing to load - it POSTed but there is now a flickering underscore in the top left of the screen so I will restart and increase the vcore.
    GA-EP45-UD3P 1.0, Intel Xeon X5470, 4x2GB Kingston HyperX DDR2 1066, NVidia Geforce 8800GTS 512, Kingston V300 240GB, Noctua NH-U12P with 2x Noctua NF-P12 Push-Pull, Corsair HX520W, Antec P182, Windows 7 64-bit

  6. #246
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Socket 771 Mod Xeon X5460 GA-P35-DS3L Overclock

    If your system double booted, were the bios settings automatically reset to standard cpu speeds?
    Sometimes a double boot after increasing cpu speed will not reset the bios to default speeds.
    It never hurts after making any bios change to re-enter the bios and to make sure that your most recent changes are still applied.

    At 401MHz your memory is operating at 802MHz so 1.9 volts should be adequate.

    tRD = 7 should be adequate but your system has been finicky, it won't hurt to set tRD = 8 now.

    There's a good chance that cpu vcore needs to be a bit higher, don't forget that you tried to o/c almost 200MHz higher.

    Here we go again, more cross posting.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  7. #247
    lukevega is offline Member
    Join Date
    Apr 2014
    Location
    Newcastle upon Tyne, England
    Posts
    307

    Default Re: Socket 771 Mod Xeon X5460 GA-P35-DS3L Overclock

    Sorry for the cross-posting! I'm about to keep everything the same except to increase vcore to 1.300000V and to set tRD =8 and try again...
    GA-EP45-UD3P 1.0, Intel Xeon X5470, 4x2GB Kingston HyperX DDR2 1066, NVidia Geforce 8800GTS 512, Kingston V300 240GB, Noctua NH-U12P with 2x Noctua NF-P12 Push-Pull, Corsair HX520W, Antec P182, Windows 7 64-bit

  8. #248
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Socket 771 Mod Xeon X5460 GA-P35-DS3L Overclock

    You currently have tRD = 7, not 8.

    When (G)MCH OverVoltage Control is set too high or too low, your system often will not boot properly.

    You might need to set cpu vcore higher.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  9. #249
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: Socket 771 Mod Xeon X5460 GA-P35-DS3L Overclock

    It takes two to cross post.

  10. #250
    lukevega is offline Member
    Join Date
    Apr 2014
    Location
    Newcastle upon Tyne, England
    Posts
    307

    Smile Re: Socket 771 Mod Xeon X5460 GA-P35-DS3L Overclock

    Ok, system running again with current BIOS settings:

    Code:
    Motherboard: Gigabyte GA-P35-DS3L Rev 2.0: BIOS Version: F9C
    CPU: Intel Xeon X5460
    RAM: Kingston Model: 4x2GB HyperX T1 DDR2-1066 CL5 Part#: KHX8500D2T1K2/4G (http://www.kingston.com/datasheets/KHX8500D2T1K2_4G.pdf)
    Power Supply Unit: Corsair HX520W
    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio __________________ [9]
    Fine Clock Ratio __________________[0]
    CPU Host Clock Control____________[Enabled]
    CPU Host Frequency (MHz)_________[390]
    PCI Express Frequency (Mhz)________[101]
    C.I.A. 2__________________________[Disabled]
    Performance Enhance = ____________[Standard]
    System Memory Multiplier (SPD)_____[2.00]
    DRAM Timing Selectable_____ SPD ___[Manual]
     
    CAS Latency Time_______________5_[5]
    Dram RAS# to CAS# Delay________5_[5]
    Dram RAS# Precharge Delay_______5_[5]
    Precharge Delay (tRAS)__________18_[18]
     
    ACT to ACT Delay (tRRD)_________3_[Auto]
    Rank Write to READ Delay________3_[Auto]
    Write to Precharge Delay_________6_[Auto]
    Refresh to ACT Delay____________52_[Auto]
    Read to Precharge Delay__________3_[Auto]
    Static tRead Value_______________8_[8]
    Static tRead Phase Adjust_________0_[Auto]
     
    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [+0.1V]
    PCI-E OverVoltage Control_ [+0.1V]
    FSB OverVoltage Control___ [+0.1V]
    (G)MCH OverVoltage Control [+0.1V]
    CPU Voltage Control_______ [1.30000V]
    Normal CPU Vcore________1.23750V
    
    Hard Disk Boot Priority.....: [Press Enter]
    1.	Kingston SV300S37A240G
    2.	ST3500320AS
    3.	ST3500320AS
    First Boot Device...........: [Hard Disk]
    Second Boot Device......: [CDROM]
    Third Boot Device.........: [Disabled]
    Boot Up Floppy Seek.....: [Disabled]
    Password Check...........: [Setup]
    HDD S.M.A.R.T. Capability......: [Disabled]
    Limit CPUID Max. to 3.........: [Disabled]
    No-Execute Memory Protect.........: [Enabled]
    CPU Enhanced Halt (C1E)...........: [Disabled]
    CPU Thermal Monitor 2(TM2) ......: [Enabled]
    CPU EIST Function...............: [Disabled]
    Virtualization Technology..........: [Disabled]
    Full Screen LOGO Show.........: [Disabled]
    Init Display First............: [PEG]
    
    SATA AHCI Mode.........: [AHCI]
    SATA Port0-1 Native Mode.........: [Enabled]
    USB Controller...........: [Enabled]
    USB 2.0 Controller............: [Enabled]
    USB Keyboard Support............: [Disabled]
    USB Mouse Support..........: [Disabled]
    Legacy USB Storage Detect…….[Disabled]
    Azalia Codec............: [Auto]
    Onboard H/W LAN............: [Enabled]
    SMART LAN.................: [Press Enter]
    Onboard LAN Boot ROM.......: [Disabled]
    Onboard IDE Controller........: [Enabled]
    Onboard Serial Port 1..........: [3F8/IRQ4]
    Onboard Parallel Serial Port...: [378/IRQ7]
    Parallel Port Mode................: [SPP]
    
    ACP1 Suspend Type........: [S3(STR)]
    USB Device Wake-Up From S3..: [Disabled]
    Soft-Off by PWR-BTTN....: [Delay 4 Sec.]
    PME Event Wake Up.......: [Disabled]
    Power On by Ring.......: [Disabled]
    Resume by Alarm......: [Disabled]
    HPET Support..........: [Enabled]
    HPET Mode.............: [64-bit mode]
    Power On by Mouse.............: [Double Click]
    Power On by Keyboard.........: [Disabled]
    AC Back Function..................: [Soft-Off]
    
    Resources Controlled By.......[Auto]
    x IRQ Resources           Press Enter
    PCI Latency Timer (CLK)......: [32]
    PCI1 IRQ Assignment.............: [Auto]
    PCI2 IRQ Assignment.............: [Auto]
    PCI3 IRQ Assignment............: [Auto]
    
    Reset Case Open Status...........: [Disabled]
    CPU Warning Temperature.......: [80°C/176°F]
    CPU FAN Fail Warning...............: [Disabled]
    SYSTEM FAN2 Fail Warning.......: [Disabled]
    POWER FAN Fail Warning..........: [Disabled]
    SYSTEM FAN1 Fail Warning.......: [Disabled]
    CPU Smart FAN Control.............: [Disabled]
    Socket 771 Mod Xeon X5460 GA-P35-DS3L Overclock-post250-jpg

    About to start a 5 loop LinX test using all available memory :)
    Last edited by lukevega; 06-10-2014 at 12:42 AM. Reason: Forgot to upload the screenshot!
    GA-EP45-UD3P 1.0, Intel Xeon X5470, 4x2GB Kingston HyperX DDR2 1066, NVidia Geforce 8800GTS 512, Kingston V300 240GB, Noctua NH-U12P with 2x Noctua NF-P12 Push-Pull, Corsair HX520W, Antec P182, Windows 7 64-bit

Page 25 of 74 FirstFirst ... 15232425262735 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 19 users browsing this thread. (1 members and 18 guests)

  1. iakoboss7

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •