Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Linux installation problem




  1. #1
    Join Date
    Nov 2001
    Posts
    381

    Default

    I'm having a problem with the installation of my Linux machine and am asking for help. I have an computer setup that has a motherboard that is using the i440bx chipset. I've disabled the onboard IDE, and am attempting to use an add-on IDE card from Promise.

    I can boot with the boot disk that I made (bare.i) and am using the color.gz root disk. I'm to the point were I need to format the hard drive. You know setup root , swap, and home partitions. But if i run the command:

    fdisk /dev/hda

    it says it cannot open the device. The IDE card is working, and It recognizes my drive. Could it be that Linux has it classified as something other than /dev/hda? Because it's an add-on IDE card? I've tried /dev/sda and any others that I know about. But I don't know about alot. So any help would be apreciated.

    Also what is the best way to clear off a drive. I mean no linux files or partitions. Also no Windows files or DOS partitions?

    Just remove the partions with fdisk under Linux?

    Thanks

  2. #2
    Join Date
    Nov 2001
    Location
    Brisvegas
    Posts
    832

    Default

    This promise card, is it a raid card?

  3. #3
    Join Date
    Nov 2001
    Posts
    381

    Default

    Nope, it's just an add-on IDE card that does UDMA 66. Rather than the onboard IDE that does UDMA 33.

    Now I was searching on google and found a couple of pieces of information that the hard drive may be named /dev/hde. And that there was an issue with Linux detecting the onboard IDE even though it is disabled. Does that sound right?

    I'm gonna try /dev/hde and see what goes on.

    Tell me if the information located here seems right.

    Any help would be appreciated.

  4. #4
    Join Date
    Nov 2001
    Location
    Brisvegas
    Posts
    832

    Default

    Try hde to hdh, one of them should be the right one.

  5. #5
    Join Date
    Mar 2004
    Posts
    2,910

    Default

    Ok, I got that problem resolved. I had already tried /dev/hde through dev/hdh and it just wouldn't access it.

    So I did some more searching and found that the kernel that I had on the boot disk (2.2.something) didn't support the Ultra66 IDE controller. I either had to patch or use another kernel. So I looked on my Slackware CDs and there was a 4.4.5 kernel. I made that boot disk and now it allows me to access the drive under /dev/hde. I can fdisk it and everything.

    But the next problem is that after I use the Slackware install to format those partitions, and move onto the install. I get CRC errors when copying from the CD. Is it possible that the Promise IDE controller doesn't reliably support ATAPI devices? I'm gonna install with the CD hooked up to the onboard IDE.

    Thx for the help. Plz keep an eye here.

  6. #6
    Join Date
    Nov 2001
    Posts
    381

    Default

    D'oh, that unregistered was me.

    Ok, I got past the CRC errors. By putting the CD-ROM on the onboard IDE channel. It appears as thought the add-on IDE card didn't reliably support the CD-ROM.

    Anyway I got Linux fully installed. I have LILO loaded in the root and have that partition /dev/hde1 set as bootable. and now it boots off of that hard drive. But it hangs when running LILO. it just does "LI". I can't figure out what is going on. I used the kernel off of the boot floppy. Any ideas?

  7. #7
    Join Date
    Nov 2001
    Location
    Brisvegas
    Posts
    832

    Default

    Lilo error messages....
    LI = The first stage boot loader was able to load the second stage boot loader, but has failed to execute it. This can either be caused by a geometry mismatch or by moving /boot/boot.b without running the map installer.
    From http://sdb.suse.de/sdb/en/html/kgw_lilo_errmsg.html

  8. #8
    Join Date
    Nov 2001
    Posts
    381

    Default

    ok, so it seems that I may have installed lilo after the 1024 cylinder boundary? How do I check.

    Also when partitioning the hard drive using fdisk there weren't overlaps in my partitions. And the same partitions worked on the onboard IDE. I don't believe it's a geometry issue.

    I'm going to re-install lilo and see what goes on.

    ...or by moving /boot/boot.b without running the map installer.
    I know that I didn't move that. But, what is it talking about, the "map installer"? Maybe it needs to be run? But how?

  9. #9
    Join Date
    Nov 2001
    Location
    Brisvegas
    Posts
    832

    Default

    You need to run the "map installer" before you reboot following any change to your lilo.conf, and you do that by doing "/sbin/lilo"
    Lilo should be on the MBR, the 1024 thing has to do with old versions of lilo not being able to boot a kernel that resides above cylinder 1024, all new versions of lilo don't have this problem. The latest is 22.2.

  10. #10
    Join Date
    Nov 2001
    Posts
    381

    Default

    Ok, I'm gonna try a newer version of LILO, because the lilo.conf looks good, and I was running /sbin/lilo before rebooting if i made any changes. I didn't know that was the "map installer", lol. It's all a learning experience. At least I know how to access the floppy. I'm just gonna figure out how to expand these files so i can install. I will take care of this problem like this -->

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •