No announcement yet.

Newb Trying to OC Q9550 on a P45-UD3R

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Newb Trying to OC Q9550 on a P45-UD3R

    I was wondering if someone can help me reach 4Ghz with this setup. I have applied optizmized settings and made the proper adjustments. . Below I have my current bios setting along with a screen shot. Thank you in advance.




    Motherboard:Gigabyte Model:P45-UD3R Rev#:1.1 Bios Version:F11
    Cpu: Q9550 EO
    Ram: Patriot, Model/Part#PGS24G8500C7K, http://www.newegg.com/Product/Product.aspx?Item=N82E16820220397
    Power Supply Unit: OCZ, Model#OCZ600MXSP, 600W
    Current Settings
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster -------------- : [FAST]
    CPU Clock Ratio ---------------------- : [8x]
    Fine CPU Clock Ratio ----------------- : [0.5]
    CPU Frequency ---------------------: 2.83GHz
    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control --------------- : [Enabled]
    CPU Host Frequency (Mhz) --------------: [333]
    PCI Express Frequency (Mhz) ---------- : [100]
    C.I.A.2 ------------------------------ : [Disabled]
    Advanced Clock Control ------- [Press Enter]
    CPU Clock Drive ---------------------- : <<< 800
    PCI Express Clock Drive -------------- : <<< 900
    CPU Clock Skew (ps) ------------------ : <<< 0ps
    MCH Clock Skew (ps) ------------------ : <<< 0ps
    DRAM Performance Control
    Performance Enhance ------------------- : [Standard]
    (G)MCH Frequency Latch ---------------- : [Auto]
    System Memory Multiplier -------------- : [3.20B]
    Memory Frequency (Mhz) ---------------- : [1066]
    DRAM Timing Selectable ---------------- : [Manual]
    Standard Timing Control
    CAS Latency Time ------------------ : [7]
    tRCD ----------------------------- : [7]
    tRP ------------------------------- : [7]
    tRAS ----------------------------- : [20]
    Advanced Timing Control
    tRRD ----------------------------- : [Auto]
    tWTR ------------------- ?? ---------- : [Auto]
    tWR --------------------- ?? ---------- : [Auto]
    tRFC ------------------- ?? ---------- : [Auto]
    tRTP ------------------- ?? ---------- : [Auto]
    Command Rate (CMD) -------------------- : [Auto]
    Driving Strength Profiles
    Driving Strength --------- : Press Enter <--- press ENTER to modify memory sub-timings when overclocking
    Channel A
    Static tRead Value --------------------- : [Auto]
    tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
    tRD Phase1 Adjustment ------------------ : [Auto]
    tRD Phase2 Adjustment ------------------ : [Auto]
    tRD Phase3 Adjustment ------------------ : [Auto]
    Trd2rd(Different Rank) ----------------- : [Auto]
    Twr2wr(Different Rank) ----------------- : [Auto]
    Twr2rd(Different Rank) ----------------- : [Auto]
    Trd2wr(Same/Diff Rank) ----------------- : [Auto]
    Dimm1 Clock Skew Control --------------- : [Auto] ps
    Dimm2 Clock Skew Control --------------- : [Auto] ps
    Channel B
    Static tRead Value --------------------- : [Auto]
    tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
    tRD Phase1 Adjustment ------------------ : [Auto]
    tRD Phase2 Adjustment ------------------ : [Auto]
    tRD Phase3 Adjustment ------------------ : [Auto]
    Trd2rd(Different Rank) ----------------- : [Auto]
    Twr2wr(Different Rank) ----------------- : [Auto]
    Twr2rd(Different Rank) ----------------- : [Auto]
    Trd2wr(Same/Diff Rank) ----------------- : [Auto]
    Dimm1 Clock Skew Control --------------- : [Auto] ps
    Dimm2 Clock Skew Control --------------- : [Auto] ps
    Motherboard Voltage Control
    CPU
    Load-Line Calibration ----------------- : [Disabled]
    CPU Vcore --------------- 1.22500V ---- : [Auto]
    CPU Termination --------- 1.200V* ----- : [Auto]
    CPU PLL ----------------- 1.500V* ----- : [Auto]
    CPU Reference ----------- 0.760V* ----- : [Auto]
    MCH/ICH
    MCH Core ---------------- 1.100V ------- : [Auto]
    MCH Reference ----------- 0.760V ------- : [Auto]
    MCH/DRAM Ref ------------ 0.900V ------ : [Auto]
    ICH I/O ----------------- 1.500V ------- : [Auto]
    ICH Core ---------------- 1.100V ------- : [Auto]
    DRAM
    DRAM Voltage ------------ 1.800V ------- : [2.100V]
    DRAM Termination -------- 0.900V ------- : [Auto]
    Channel A Reference ----- 0.900V ------- : [Auto]
    Channel B Reference ----- 0.900V ------- : [Auto]
    Advanced Settings
    Limit CPUID Max. to 3 ------------------ : [Disabled]
    No-Execute Memory Protect -------------- : [Enabled]
    CPU Enhanced Halt (C1E) ---------------- : [Disabled]
    C2/C2E State Support ------------------- : [Disabled]
    x C4/C4E State Support ----------------- : [Disabled]
    CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
    CPU EIST Function --------------------- : [Disabled]
    Virtualization Technology -------------- : [Enabled]
    Integrated Peripherals
    Legacy USB Storage Detect ------------- : [Disabled]
    Attached Files

  • #2
    Re: Newb Trying to OC Q9550 on a P45-UD3R

    Hey guys I finally have stable settings at 4.00ghz. Also I ended up chaning my ram to mushkin. I was wondering if anyone could take a look and see if my settings are at optimal performance. Thanks






    Motherboard:Gigabyte Model:P45-UD3R Rev#:1.1 Bios Version:F11
    Cpu: Q9550 EO
    Ram: Mushkin, Model/Part#Blackline Ascent Heatsink 996619, Newegg.com - Mushkin Enhanced Blackline Ascent Heatsink 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 1066 (PC2 8500) Dual Channel Kit Desktop Memory Model 996619 - Desktop Memory
    Power Supply Unit: OCZ, Model#OCZ600MXSP, 600W
    Current Settings
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster -------------- : [FAST]
    CPU Clock Ratio ---------------------- : [8x]
    Fine CPU Clock Ratio ----------------- : [0.5]
    CPU Frequency ---------------------: 4.00GHz
    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control --------------- : [Enabled]
    CPU Host Frequency (Mhz) --------------: [471]
    PCI Express Frequency (Mhz) ---------- : [100]
    C.I.A.2 ------------------------------ : [Disabled]
    Advanced Clock Control ------- [Press Enter]
    CPU Clock Drive ---------------------- : <<< 800
    PCI Express Clock Drive -------------- : <<< 900
    CPU Clock Skew (ps) ------------------ : <<< 0ps
    MCH Clock Skew (ps) ------------------ : <<< 0ps
    DRAM Performance Control
    Performance Enhance ------------------- : [Standard]
    (G)MCH Frequency Latch ---------------- : [Auto]
    System Memory Multiplier -------------- : [2.00D]
    Memory Frequency (Mhz) ---------------- : [942]
    DRAM Timing Selectable ---------------- : [Manual]
    Standard Timing Control
    CAS Latency Time ------------------ : [5]
    tRCD ----------------------------- : [5]
    tRP ------------------------------- : [5]
    tRAS ----------------------------- : [15]
    Advanced Timing Control
    tRRD ----------------------------- : [Auto]
    tWTR ----------------------------- : [Auto]
    tWR ------------------------------- : [Auto]
    tRFC ----------------------------- : [Auto]
    tRTP ----------------------------- : [Auto]
    Command Rate (CMD) -------------------- : [Auto]
    Driving Strength Profiles
    Driving Strength --------- : [Auto]
    Channel A
    Static tRead Value --------------------- : [Auto]
    tRD Phase0 Adjustment ------------------ : [Auto]
    tRD Phase1 Adjustment ------------------ : [Auto]
    tRD Phase2 Adjustment ------------------ : [Auto]
    tRD Phase3 Adjustment ------------------ : [Auto]
    Trd2rd(Different Rank) ----------------- : [Auto]
    Twr2wr(Different Rank) ----------------- : [Auto]
    Twr2rd(Different Rank) ----------------- : [Auto]
    Trd2wr(Same/Diff Rank) ----------------- : [Auto]
    Dimm1 Clock Skew Control --------------- : [Auto] ps
    Dimm2 Clock Skew Control --------------- : [Auto] ps
    Channel B
    Static tRead Value --------------------- : [Auto]
    tRD Phase0 Adjustment ------------------ : [Auto]
    tRD Phase1 Adjustment ------------------ : [Auto]
    tRD Phase2 Adjustment ------------------ : [Auto]
    tRD Phase3 Adjustment ------------------ : [Auto]
    Trd2rd(Different Rank) ----------------- : [Auto]
    Twr2wr(Different Rank) ----------------- : [Auto]
    Twr2rd(Different Rank) ----------------- : [Auto]
    Trd2wr(Same/Diff Rank) ----------------- : [Auto]
    Dimm1 Clock Skew Control --------------- : [Auto] ps
    Dimm2 Clock Skew Control --------------- : [Auto] ps
    Motherboard Voltage Control
    CPU
    Load-Line Calibration ----------------- : [Disabled]
    CPU Vcore --------------- 1.22500V ---- : [1.35000V]
    CPU Termination --------- 1.200V* ----- : [1.280V]
    CPU PLL ----------------- 1.500V* ----- : [1.570V]
    CPU Reference ----------- 0.760V* ----- : [0.835V]
    MCH/ICH
    MCH Core ---------------- 1.100V ------- : [1.320V]
    MCH Reference ----------- 0.760V ------- : [0.835V]
    MCH/DRAM Ref ------------ 0.900V ------ : [1.000V]
    ICH I/O ----------------- 1.500V ------- : [1.500V]
    ICH Core ---------------- 1.100V ------- : [1.100V]
    DRAM
    DRAM Voltage ------------ 1.800V ------- : [2.000V]
    DRAM Termination -------- 0.900V ------- : [Auto]
    Channel A Reference ----- 0.900V ------- : [Auto]
    Channel B Reference ----- 0.900V ------- : [Auto]
    Advanced Settings
    Limit CPUID Max. to 3 ------------------ : [Disabled]
    No-Execute Memory Protect -------------- : [Enabled]
    CPU Enhanced Halt (C1E) ---------------- : [Disabled]
    C2/C2E State Support ------------------- : [Disabled]
    x C4/C4E State Support ----------------- : [Disabled]
    CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
    CPU EIST Function --------------------- : [Disabled]
    Virtualization Technology -------------- : [Enabled]
    Integrated Peripherals
    Legacy USB Storage Detect ------------- : [Disabled]

    Comment


    • #3
      Re: Newb Trying to OC Q9550 on a P45-UD3R

      Screen capture was taken with patriot memory so not much to say about that.
      Static tRead Value left on auto so probably not set for optimal performance, try setting it as low as possible for both channels.

      Comment


      • #4
        Re: Newb Trying to OC Q9550 on a P45-UD3R

        Originally posted by Chike View Post
        Screen capture was taken with patriot memory so not much to say about that.
        Static tRead Value left on auto so probably not set for optimal performance, try setting it as low as possible for both channels.
        I just got the ram today. Im doing a thorough memory test on it to make sure everything is okay. What do you think about my voltages are they too high for the speed im running ? Also if I wanted to do 500 fsb how much more do you think i would have to bump the current voltages. BTW I will do a new prime test tomorrow and ill post that up asap with the new mushkin ram.

        Comment


        • #5
          Re: Newb Trying to OC Q9550 on a P45-UD3R

          Voltages look within reason to me, maybe you can try to lower MCH Core. It's still ok just make sure there's enough air flow around the NB.

          Comment

          Working...
          X