No announcement yet.

Settings Please

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Settings Please

    Hello. Just built my new system and would like to OC a little.

    EP45-UD3R
    E8400
    Mushkin Redline PC2-8000 2x2GB
    EVGA 8800 gt (from previous system)

    Seems that going from 3 to 3.6 on the E8400 is considered safe. Could I get the best Bios settings for my setup? Thanks.

  • #2
    Re: Settings Please

    Try this, with ram at 960 >>>>

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto or Fast
    CPU Clock Ratio ..........................: 9
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 3.609


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 401Mhz (May need to use 399, or you will have to use 2.66D below and 555-15/18 ram settings for 1066Mhz)

    PCI Express Frequency (Mhz) .........:Set to 100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<<
    MCH Clock Skew (ps)...................: <<<


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 2.40B

    Memory Frequency (Mhz) ..............: 962Mhz
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................5
    tRCD .........................................5
    tRP'...........................................5
    tRAS..........................................12

    Advanced Timing Control
    tRRD...........................................3-4
    tWTR..........................................3-5
    tWR............................................4-6
    tRFC...........................................52-62
    tRTP...........................................3-5
    Command Rate (CMD) ....................:2

    Driving Strength Profiles
    Driving Strength ............................800/1066 (Test both, set 1066 now)

    Channel A
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:1.25-1.36 (All up to your chip)

    CPU Termination…..... 1.200V*.......: <<< 1.2-1.36 (1.2-1.28 likely plenty)
    CPU PLL…………………....1.500V*.......: << 1.5-1.58

    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly

    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly

    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.2-1.3 (1.22-1.26 likely good)
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< 1.5-1.6
    ICH Core…………...……1.100V............: <<< 1.1x-1.2

    DRAM
    DRAM Voltage ……....1.800V............: 2.0-2.1
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

    Comment

    Working...
    X