Hi there, new here and to the GA boards so excuse the nature of the post.
As I said I am new to the GA product and to OC in general, but I would like to OC my E8600 to about 3.8-4.0 GHZ. I would also like to use the G Skill DDR2-9600 ram in the setup. I will be using this for Flight Sim X with Accel.
I have also taken the time to include a template of the settings which allowed me to start windows, which I got from the G Skill site.
Sorry if my 1st post was a long 1!
Doug
Simplified Template For users who may not be sure of anything in the MIT Section
Motherboard: Model:EP 45 UD3R Rev#: 1.1Bios Version: F11
Cpu: Model: E 8600
Ram: Brand, G Skill Model/Part# F2-9600CL5D-4GBPI
Power Supply Unit: Brand Antec, Model# True Power Quatro, Wattage 850
Win 7 Home Premium 64 Bit
note: replace all ?? with the value displayed in your bios.
----> Replace "Auto" with manually set values.
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto]
CPU Clock Ratio ---------------------- : [???]
Fine CPU Clock Ratio ----------------- : [0.0] <-- ignore if not available
CPU Frequency ---------------------: #### <-- this is set by your bios
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [375]
PCI Express Frequency (Mhz) ---------- : [100] <--- Set to 100, never leave this on Auto
C.I.A.2 ------------------------------ : [Disabled]
Advanced Clock Control ------- [Press Enter]
CPU Clock Drive ---------------------- : [???]
PCI Express Clock Drive -------------- : [???]
CPU Clock Skew (ps) ------------------ : [???]
MCH Clock Skew (ps) ------------------ : [???]
DRAM Performance Control
Performance Enhance ------------------- : [Standard] <--- set to STANDARD when overclocking
Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <--- Leave this Disabled
(G)MCH Frequency Latch ---------------- : [Auto]
System Memory Multiplier -------------- : [3.20B] <-- this is the setting that you are using
Memory Frequency (Mhz) ---------------- : [Auto]
DRAM Timing Selectable ---------------- : [Manual] <-- set to MANUAL for overclocking
Standard Timing Control
CAS Latency Time -------- 5 ---------- : [Auto]
tRCD ------------------- 5---------- : [Auto]
tRP --------------------- 5 ---------- : [Auto]
tRAS ------------------- 15 ---------- : [Auto]
Advanced Timing Control
tRRD ------------------- 4 ---------- : [Auto]
tWTR ------------------- 4 ---------- : [Auto]
tWR --------------------- 8 ---------- : [Auto]
tRFC ------------------- 70---------- : [Auto]
tRTP ------------------- 4 ---------- : [Auto]
Command Rate (CMD) -------------------- : [2] <--- Auto or 0 is OK
Driving Strength Profiles
Driving Strength --------- : Press Enter <--- press ENTER to modify memory sub-timings when overclocking
Channel A
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Channel B
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Motherboard Voltage Control
CPU
Voltage Types------------ Normal -------- Current -----
Load-Line Calibration ----------------- : [Disabled]
CPU Vcore --------------- 1.25 ---- : [Auto]
CPU Termination --------- ?.???V* ----- : [Auto]
CPU PLL ----------------- ?.???V* ----- : [Auto]
CPU Reference ----------- ?.???V* ----- : [Auto]
CPU Reference2 ---------- ?.???V* ----- : [Auto]
MCH/ICH
MCH Core ---------------- 1.20V ------- : [Auto]
MCH Reference ----------- ?.???V ------- : [Auto]
MCH/DRAM Ref ------------ 1.0V ------ : [Auto]
ICH I/O ----------------- 1.6V ------- : [Auto]
ICH Core ---------------- 1.20V ------- : [Auto]
DRAM
DRAM Voltage ------------ 1.90V ------- : [Auto]
DRAM Termination -------- ?.???V ------- : [Auto]
Channel A Reference ----- ?.???V ------- : [Auto]
Channel B Reference ----- ?.???V ------- : [Auto]
Advanced Settings
Limit CPUID Max. to 3 ------------------ : [Disabled]
No-Execute Memory Protect -------------- : [Enabled]
CPU Enhanced Halt (C1E) ---------------- : [Disabled]
C2/C2E State Support ------------------- : [Disabled]
x C4/C4E State Support ----------------- : [Disabled]
CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
CPU EIST Function --------------------- : [Disabled]
Virtualization Technology -------------- : [Disabled]
Integrated Peripherals
Legacy USB Storage Detect ------------- : [Disabled]
__________________
As I said I am new to the GA product and to OC in general, but I would like to OC my E8600 to about 3.8-4.0 GHZ. I would also like to use the G Skill DDR2-9600 ram in the setup. I will be using this for Flight Sim X with Accel.
I have also taken the time to include a template of the settings which allowed me to start windows, which I got from the G Skill site.
Sorry if my 1st post was a long 1!
Doug
Simplified Template For users who may not be sure of anything in the MIT Section
Motherboard: Model:EP 45 UD3R Rev#: 1.1Bios Version: F11
Cpu: Model: E 8600
Ram: Brand, G Skill Model/Part# F2-9600CL5D-4GBPI
Power Supply Unit: Brand Antec, Model# True Power Quatro, Wattage 850
Win 7 Home Premium 64 Bit
note: replace all ?? with the value displayed in your bios.
----> Replace "Auto" with manually set values.
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto]
CPU Clock Ratio ---------------------- : [???]
Fine CPU Clock Ratio ----------------- : [0.0] <-- ignore if not available
CPU Frequency ---------------------: #### <-- this is set by your bios
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [375]
PCI Express Frequency (Mhz) ---------- : [100] <--- Set to 100, never leave this on Auto
C.I.A.2 ------------------------------ : [Disabled]
Advanced Clock Control ------- [Press Enter]
CPU Clock Drive ---------------------- : [???]
PCI Express Clock Drive -------------- : [???]
CPU Clock Skew (ps) ------------------ : [???]
MCH Clock Skew (ps) ------------------ : [???]
DRAM Performance Control
Performance Enhance ------------------- : [Standard] <--- set to STANDARD when overclocking
Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <--- Leave this Disabled
(G)MCH Frequency Latch ---------------- : [Auto]
System Memory Multiplier -------------- : [3.20B] <-- this is the setting that you are using
Memory Frequency (Mhz) ---------------- : [Auto]
DRAM Timing Selectable ---------------- : [Manual] <-- set to MANUAL for overclocking
Standard Timing Control
CAS Latency Time -------- 5 ---------- : [Auto]
tRCD ------------------- 5---------- : [Auto]
tRP --------------------- 5 ---------- : [Auto]
tRAS ------------------- 15 ---------- : [Auto]
Advanced Timing Control
tRRD ------------------- 4 ---------- : [Auto]
tWTR ------------------- 4 ---------- : [Auto]
tWR --------------------- 8 ---------- : [Auto]
tRFC ------------------- 70---------- : [Auto]
tRTP ------------------- 4 ---------- : [Auto]
Command Rate (CMD) -------------------- : [2] <--- Auto or 0 is OK
Driving Strength Profiles
Driving Strength --------- : Press Enter <--- press ENTER to modify memory sub-timings when overclocking
Channel A
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Channel B
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Motherboard Voltage Control
CPU
Voltage Types------------ Normal -------- Current -----
Load-Line Calibration ----------------- : [Disabled]
CPU Vcore --------------- 1.25 ---- : [Auto]
CPU Termination --------- ?.???V* ----- : [Auto]
CPU PLL ----------------- ?.???V* ----- : [Auto]
CPU Reference ----------- ?.???V* ----- : [Auto]
CPU Reference2 ---------- ?.???V* ----- : [Auto]
MCH/ICH
MCH Core ---------------- 1.20V ------- : [Auto]
MCH Reference ----------- ?.???V ------- : [Auto]
MCH/DRAM Ref ------------ 1.0V ------ : [Auto]
ICH I/O ----------------- 1.6V ------- : [Auto]
ICH Core ---------------- 1.20V ------- : [Auto]
DRAM
DRAM Voltage ------------ 1.90V ------- : [Auto]
DRAM Termination -------- ?.???V ------- : [Auto]
Channel A Reference ----- ?.???V ------- : [Auto]
Channel B Reference ----- ?.???V ------- : [Auto]
Advanced Settings
Limit CPUID Max. to 3 ------------------ : [Disabled]
No-Execute Memory Protect -------------- : [Enabled]
CPU Enhanced Halt (C1E) ---------------- : [Disabled]
C2/C2E State Support ------------------- : [Disabled]
x C4/C4E State Support ----------------- : [Disabled]
CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
CPU EIST Function --------------------- : [Disabled]
Virtualization Technology -------------- : [Disabled]
Integrated Peripherals
Legacy USB Storage Detect ------------- : [Disabled]
__________________
Comment