No announcement yet.

Oc ram + cpu

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Oc ram + cpu

    Hi there,just need a bit of help.Ive found thread on this forum about my MB,but with different CPU,so im sorry if its same topic,just want to be sure that every1 counts with my setup.So,my setup is:
    MB:Gigabyte EP43T-USB3
    CPU: Intel Core2Quad Q9550 @ 2,83GHz
    RAM: Kingston 2x2GB 1600MHz CL8 (KHX1600C8D3K2/4GX to be correct)
    GPU: ATI Radeon HD5770
    Windows 7 Ultimate,fresh instalation

    Well,my problem is that i cant run RAMs at 1600MHz when my BUS is set at 333MHz.So ive tried to rise it up to 400MHz,CPU freq at 3,4GHz with multiplier at 8,5,didnt change the CPU voltages,just tried once 1,35V Vcore.RAM timing was 8-8-8-24,RAM voltage 1,66V(Unable to set 1,65V-steps are at 0,02V).

    While ive been trying to run it at this setup,PC freezes at Windows loading screen or doesnt get so far,many times restart right after start logo.(Many times means rly many,like 30times reboot after logo and unable to get into BIOS or even to do quick recovery from second BIOS :/ )

    So,does any1 have any info how to solve this prob-to run CPU about 3,4GHz,DDR =>1600 ? TY for all ideas ;)
    BTW: Im sry for my english if there are some/loads of mistakes ;)

    If you need any info about PC,settings, ect,just post it.Ill try to get it all,cant find help elsewhere :ยด(

  • #2
    Re: Oc ram + cpu

    Please grab a template from my signature and give me your current full settings you are trying and I will advise back.

    Please also link us to your memory

    Comment


    • #3
      Re: Oc ram + cpu

      Hi,there are my default specs from bios.
      Im new in OC and wanted to get CPU over 3,4GHz,400FSB for 1600MHz DDR with CL8 or higher freq with CL9,but i dont know what to change to get it,so hope that you can help me to figure it out

      Motherboard:Gigabyte Model:EP43T-USB3 Rev#:A3 Bios Version:F2 01/07/2010
      Cpu:Intel Core2Quad Q9550 @ 2,83GHz
      Ram: Kingston KHX1600C8D3K2/4GX(Kingston HyperX DDR3 4gig Memory Kit 1600Mhz KHX1600C8D3K2/4GX 1.65V Reviewed )
      Power Supply Unit:CORSAIR TX750


      MB Intelligent Tweaker(M.I.T.)
      Robust Graphics Booster -------------- : [Auto]
      CPU Clock Ratio ---------------------- : [8x]
      Fine CPU Clock Ratio ----------------- : [0.5]
      CPU Frequency ---------------------: 2,83GHz(333x8.5)

      Clock Chip Control
      Standard Clock Control
      CPU Host Clock Control --------------- : [Disabled]
      CPU Host Frequency (Mhz) --------------: [333]
      PCI Express Frequency (Mhz) ---------- : [Auto]

      C.I.A.2 ------------------------------ : [Disabled]

      Advanced Clock Control ------- [Press Enter]
      CPU Clock Drive ---------------------- : [800mV]
      PCI Express Clock Drive -------------- : [800mV]
      CPU Clock Skew (ps) ------------------ : [0]
      MCH Clock Skew (ps) ------------------ : [0]

      DRAM Performance Control
      Performance Enhance ------------------- : [Turbo]
      Extreme Memory Profile --- (X.M.P.) --- : [Auto]
      (G)MCH Frequency Latch ---------------- : [Auto]
      System Memory Multiplier -------------- : [Auto]
      Memory Frequency (Mhz) ---------------- : [1333]
      DRAM Timing Selectable ---------------- : [Auto]

      Standard Timing Control
      CAS Latency Time -------- 9 ---------- : [Auto]
      tRCD ------------------- 9 ---------- : [Auto]
      tRP --------------------- 9 ---------- : [Auto]
      tRAS ------------------- 24 ---------- : [Auto]

      Advanced Timing Control
      tRRD ------------------- 4 ---------- : [Auto]
      tWTR ------------------- 5 ---------- : [Auto]
      tWR --------------------- 10 ---------- : [Auto]
      tRFC ------------------- 74 ---------- : [Auto]
      tRTP ------------------- 5 ---------- : [Auto]
      Command Rate (CMD) -------------------- :0

      Channel A
      Static tRead Value --------------------- :7 [Auto]
      tRD Phase0 Adjustment ------------------ :0 [Auto] <-- leave this and below set to AUTO
      tRD Phase1 Adjustment ------------------ :0 [Auto]
      tRD Phase2 Adjustment ------------------ :1 [Auto]
      tRD Phase3 Adjustment ------------------ :1 [Auto]
      Trd2rd(Different Rank) ----------------- :7 [Auto]
      Twr2wr(Different Rank) ----------------- :6 [Auto]
      Twr2rd(Different Rank) ----------------- :6 [Auto]
      Trd2wr(Same/Diff Rank) ----------------- :9 [Auto]
      Dimm1 Clock Skew Control --------------- : [Auto] ps
      Dimm2 Clock Skew Control --------------- : [Auto] ps

      Channel B
      Static tRead Value --------------------- :7 [Auto]
      tRD Phase0 Adjustment ------------------ :0 [Auto] <-- leave this and below set to AUTO
      tRD Phase1 Adjustment ------------------ :0 [Auto]
      tRD Phase2 Adjustment ------------------ :1 [Auto]
      tRD Phase3 Adjustment ------------------ :1 [Auto]
      Trd2rd(Different Rank) ----------------- :7 [Auto]
      Twr2wr(Different Rank) ----------------- :6 [Auto]
      Twr2rd(Different Rank) ----------------- :6 [Auto]
      Trd2wr(Same/Diff Rank) ----------------- :9 [Auto]
      Dimm1 Clock Skew Control --------------- : [Auto] ps
      Dimm2 Clock Skew Control --------------- : [Auto] ps


      Motherboard Voltage Control
      CPU
      Voltage Types------------ Normal -------- Current -----
      Load-Line Calibration ----------------- : [Disabled]
      CPU Vcore --------------- 1,22500V ---- : [Auto]

      CPU Termination --------- 1,2V ----- : [Auto]
      CPU PLL ----------------- 1,550V ----- : [Auto]

      CPU Reference ----------- 0,805V* ----- : [Auto]
      CPU Reference2 ---------- ?.???V* ----- : [Auto]

      MCH/ICH
      MCH Core ---------------- 1,100V ------- : [Auto]
      MCH Reference ----------- 0,760V ------- : [Auto]
      MCH/DRAM Ref ------------ ?????V ------ : [Auto]
      ICH I/O ----------------- 1,550V ------- : [Auto]
      ICH Core ---------------- 1,100V ------- : [Auto]
      DRAM
      DRAM Voltage ------------ 1,500V ------- : [Auto]
      DRAM Termination -------- 0,750V ------- : [Auto]
      Channel A Reference ----- ?.???V ------- : [Auto]
      Channel B Reference ----- ?.???V ------- : [Auto]

      Advanced Settings
      Limit CPUID Max. to 3 ------------------ : [Disabled]
      No-Execute Memory Protect -------------- : [Enabled]
      CPU Enhanced Halt (C1E) ---------------- : [Disabled] Dont have
      C2/C2E State Support ------------------- : [Disabled]
      x C4/C4E State Support ----------------- : [Disabled]
      CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
      CPU EIST Function --------------------- : [Enabled]
      Virtualization Technology -------------- : [Disabled]

      Integrated Peripherals
      Legacy USB Storage Detect ------------- : [Disabled]

      Comment


      • #4
        Re: Oc ram + cpu

        Thanks!

        Try this for 3.4Ghz for now, if you have a good cooler you can likely go higher if you want.

        BIOS F3 is out if you want to try it out:
        http://download.gigabyte.us/FileList...3t-usb3_f3.exe

        If you do, please use Qflash or DOS to update the BIOS, here is a guide:
        http://forums.tweaktown.com/f69/bios...h-guide-27576/

        MB Intelligent Tweaker(M.I.T.)
        Robust Graphics Booster -------------- : [Auto or Fast]
        CPU Clock Ratio ---------------------- : [8x]
        Fine CPU Clock Ratio ----------------- : [0.5]
        CPU Frequency ---------------------: 3.4

        Clock Chip Control
        Standard Clock Control
        CPU Host Clock Control --------------- : [Disabled] << Enabled
        CPU Host Frequency (Mhz) --------------: [333] << 400
        PCI Express Frequency (Mhz) ---------- : [Auto] << Set 100

        C.I.A.2 ------------------------------ : [Disabled]

        Advanced Clock Control ------- [Press Enter]
        CPU Clock Drive ---------------------- : [800mV]
        PCI Express Clock Drive -------------- : [800mV]
        CPU Clock Skew (ps) ------------------ : [0]
        MCH Clock Skew (ps) ------------------ : [0]

        DRAM Performance Control
        Performance Enhance ------------------- : [Turbo] << Standard
        Extreme Memory Profile --- (X.M.P.) --- : [Auto] << Disabled
        (G)MCH Frequency Latch ---------------- : [Auto]
        System Memory Multiplier -------------- : [Auto] << 4.00B or 4.00D if you have
        Memory Frequency (Mhz) ---------------- : [1600]
        DRAM Timing Selectable ---------------- : [Auto] << manual

        Standard Timing Control
        CAS Latency Time -------- 9 ---------- : 8
        tRCD ------------------- 9 ---------- : 8
        tRP --------------------- 9 ---------- : 8
        tRAS ------------------- 24 ---------- : 24

        Advanced Timing Control
        tRRD ------------------- 4 ---------- : 4-5
        tWTR ------------------- 5 ---------- : 4-8
        tWR --------------------- 10 ---------- :6-10
        tRFC ------------------- 74 ---------- : 62-74
        tRTP ------------------- 5 ---------- : 4-5
        Command Rate (CMD) -------------------- :0 << Set 2T for now, try 1T later

        Channel A
        Static tRead Value --------------------- :7 [Auto] << 8-9 (Set 9 for now)
        tRD Phase0 Adjustment ------------------ :0 [Auto] <-- leave this and below set to AUTO
        tRD Phase1 Adjustment ------------------ :0 [Auto]
        tRD Phase2 Adjustment ------------------ :1 [Auto]
        tRD Phase3 Adjustment ------------------ :1 [Auto]
        Trd2rd(Different Rank) ----------------- :7 [Auto]
        Twr2wr(Different Rank) ----------------- :6 [Auto]
        Twr2rd(Different Rank) ----------------- :6 [Auto]
        Trd2wr(Same/Diff Rank) ----------------- :9 [Auto]
        Dimm1 Clock Skew Control --------------- : [Auto] ps
        Dimm2 Clock Skew Control --------------- : [Auto] ps

        Channel B
        Static tRead Value --------------------- :7 [Auto] << 8-9 (Set 9 for now)
        tRD Phase0 Adjustment ------------------ :0 [Auto] <-- leave this and below set to AUTO
        tRD Phase1 Adjustment ------------------ :0 [Auto]
        tRD Phase2 Adjustment ------------------ :1 [Auto]
        tRD Phase3 Adjustment ------------------ :1 [Auto]
        Trd2rd(Different Rank) ----------------- :7 [Auto]
        Twr2wr(Different Rank) ----------------- :6 [Auto]
        Twr2rd(Different Rank) ----------------- :6 [Auto]
        Trd2wr(Same/Diff Rank) ----------------- :9 [Auto]
        Dimm1 Clock Skew Control --------------- : [Auto] ps
        Dimm2 Clock Skew Control --------------- : [Auto] ps


        Motherboard Voltage Control
        CPU
        Voltage Types------------ Normal -------- Current -----
        Load-Line Calibration ----------------- : [Disabled] << Enabled -Level 1
        CPU Vcore --------------- 1,22500V ---- : [Auto] << all up to your CPU, stock value manually set may get you 3.4Ghz, but maybe not. You may need 1.25-1.36 or so.

        CPU Termination --------- 1,2V ----- : [Auto] << set 1.225-1.34
        CPU PLL ----------------- 1,550V ----- : [Auto] << Set 1.5

        CPU Reference ----------- 0,805V* ----- : [Auto]
        CPU Reference2 ---------- ?.???V* ----- : [Auto]

        MCH/ICH
        MCH Core ---------------- 1,100V ------- : [Auto] << Set 1.2-1.28
        MCH Reference ----------- 0,760V ------- : [Auto]
        MCH/DRAM Ref ------------ ?????V ------ : [Auto]
        ICH I/O ----------------- 1,550V ------- : [Auto]
        ICH Core ---------------- 1,100V ------- : [Auto]

        DRAM
        DRAM Voltage ------------ 1,500V ------- : [Auto] << Set 1.66
        DRAM Termination -------- 0,750V ------- : [Auto]
        Channel A Reference ----- ?.???V ------- : [Auto]
        Channel B Reference ----- ?.???V ------- : [Auto]

        Advanced Settings
        Limit CPUID Max. to 3 ------------------ : [Disabled]
        No-Execute Memory Protect -------------- : [Enabled]
        CPU Enhanced Halt (C1E) ---------------- : [Disabled] Dont have << Disable, it should be there for sure, maybe BIOS bug?
        C2/C2E State Support ------------------- : [Disabled]
        x C4/C4E State Support ----------------- : [Disabled]
        CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
        CPU EIST Function --------------------- : [Enabled] << Disable
        Virtualization Technology -------------- : [Disabled]

        Integrated Peripherals
        Legacy USB Storage Detect ------------- : [Disabled]

        Comment


        • #5
          Re: Oc ram + cpu

          Well,got after few seconds in system BSOD 74 and on second try 109.Cant find the database and dont have more time to try different settings.Work sux :(

          Comment


          • #6
            Re: Oc ram + cpu

            I posted ranges for you to try, so since you are having issues please post back for me the exact settings you are trying that fail and I will advise back

            Comment


            • #7
              Re: Oc ram + cpu

              Probably need tRFC 82-90 for DDR-1600.

              Comment


              • #8
                Re: Oc ram + cpu

                Ok,values ive been trying.Just PC resets everytime when loading system logo shows up->xtra fast BSOD.

                MB Intelligent Tweaker(M.I.T.)
                Robust Graphics Booster -------------- : [Auto]
                CPU Clock Ratio ---------------------- : [8x]
                Fine CPU Clock Ratio ----------------- : [0.5]
                CPU Frequency ---------------------: 3.4

                Clock Chip Control
                Standard Clock Control
                CPU Host Clock Control --------------- : [enabled]
                CPU Host Frequency (Mhz) --------------: [400]
                PCI Express Frequency (Mhz) ---------- : [100]

                C.I.A.2 ------------------------------ : [Disabled]

                Advanced Clock Control ------- [Press Enter]
                CPU Clock Drive ---------------------- : [800mV]
                PCI Express Clock Drive -------------- : [800mV]
                CPU Clock Skew (ps) ------------------ : [0]
                MCH Clock Skew (ps) ------------------ : [0]

                DRAM Performance Control
                Performance Enhance ------------------- : [Standard]
                Extreme Memory Profile --- (X.M.P.) --- : [Disabled]
                (G)MCH Frequency Latch ---------------- : [Auto]
                System Memory Multiplier -------------- : [4.00D]
                Memory Frequency (Mhz) ---------------- : [1600]
                DRAM Timing Selectable ---------------- : [Manual]

                Standard Timing Control
                CAS Latency Time -------- 9 ---------- : 8
                tRCD ------------------- 9 ---------- : 8
                tRP --------------------- 9 ---------- : 8
                tRAS ------------------- 24 ---------- : 24

                Advanced Timing Control
                tRRD ------------------- 4 ---------- : 4
                tWTR ------------------- 5 ---------- : 6
                tWR --------------------- 10 ---------- :8
                tRFC ------------------- 74 ---------- : 69
                tRTP ------------------- 5 ---------- : 4
                Command Rate (CMD) -------------------- :2

                Channel A
                Static tRead Value --------------------- :9
                tRD Phase0 Adjustment ------------------ :0 [Auto]
                tRD Phase1 Adjustment ------------------ :0 [Auto]
                tRD Phase2 Adjustment ------------------ :1 [Auto]
                tRD Phase3 Adjustment ------------------ :1 [Auto]
                Trd2rd(Different Rank) ----------------- :7 [Auto]
                Twr2wr(Different Rank) ----------------- :6 [Auto]
                Twr2rd(Different Rank) ----------------- :6 [Auto]
                Trd2wr(Same/Diff Rank) ----------------- :9 [Auto]
                Dimm1 Clock Skew Control --------------- : [Auto] ps
                Dimm2 Clock Skew Control --------------- : [Auto] ps

                Channel B
                Static tRead Value --------------------- :9 [Auto]
                tRD Phase0 Adjustment ------------------ :0 [Auto]
                tRD Phase1 Adjustment ------------------ :0 [Auto]
                tRD Phase2 Adjustment ------------------ :1 [Auto]
                tRD Phase3 Adjustment ------------------ :1 [Auto]
                Trd2rd(Different Rank) ----------------- :7 [Auto]
                Twr2wr(Different Rank) ----------------- :6 [Auto]
                Twr2rd(Different Rank) ----------------- :6 [Auto]
                Trd2wr(Same/Diff Rank) ----------------- :9 [Auto]
                Dimm1 Clock Skew Control --------------- : [Auto] ps
                Dimm2 Clock Skew Control --------------- : [Auto] ps


                Motherboard Voltage Control
                CPU
                Voltage Types------------ Normal -------- Current -----
                Load-Line Calibration ----------------- : [Disabled]
                CPU Vcore --------------- 1,22500V ---- :1,33125V

                CPU Termination --------- 1,2V ----- : 1,3V
                CPU PLL ----------------- 1,550V ----- : 1,550V (steps only 1.55,1.66 ect)

                CPU Reference ----------- 0,805V* ----- : [Auto]
                CPU Reference2 ---------- ?.???V* ----- : [Auto]

                MCH/ICH
                MCH Core ---------------- 1,100V ------- :1,26
                MCH Reference ----------- 0,760V ------- : [Auto]
                MCH/DRAM Ref ------------ ?????V ------ : [Auto]
                ICH I/O ----------------- 1,550V ------- : [Auto]
                ICH Core ---------------- 1,100V ------- : [Auto]

                DRAM
                DRAM Voltage ------------ 1,500V ------- :1,66V
                DRAM Termination -------- 0,750V ------- : [Auto]
                Channel A Reference ----- ?.???V ------- : [Auto]
                Channel B Reference ----- ?.???V ------- : [Auto]

                Advanced Settings
                Limit CPUID Max. to 3 ------------------ : [Disabled]
                No-Execute Memory Protect -------------- : [Enabled]
                CPU Enhanced Halt (C1E) ---------------- : [Disabled]
                C2/C2E State Support ------------------- : [Disabled]
                x C4/C4E State Support ----------------- : [Disabled]
                CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
                CPU EIST Function --------------------- : [Disabled]
                Virtualization Technology -------------- : [Disabled]

                Integrated Peripherals
                Legacy USB Storage Detect ------------- : [Disabled]

                hope thats all... got a free few days,so going to try it in the evening with different setups,if you have any ideas,post it,ill write it on a paper and try everything even it sounds crazy,just want to run it as fast as possible ^^

                Comment


                • #9
                  Re: Oc ram + cpu

                  tRFC is 110ns for this RAM so definately set it to 88. I'd leave all advance timings auto to begin with, then you can play after you get started.
                  There's not much benefit for DDR-1600 at 400MHz FSB so you may try DDR-1333 multiplier 3.33D with 7-7-7-19/20 timings, that would be just as good performance wise.

                  It would help if you add your system specs to your forum signature, including the link to ram data sheet

                  Comment


                  • #10
                    Re: Oc ram + cpu

                    Try this

                    MB Intelligent Tweaker(M.I.T.)
                    Robust Graphics Booster -------------- : [Auto]
                    CPU Clock Ratio ---------------------- : [8x]
                    Fine CPU Clock Ratio ----------------- : [0.5]
                    CPU Frequency ---------------------: 3.4

                    Clock Chip Control
                    Standard Clock Control
                    CPU Host Clock Control --------------- : [enabled]
                    CPU Host Frequency (Mhz) --------------: [400]
                    PCI Express Frequency (Mhz) ---------- : [100]

                    C.I.A.2 ------------------------------ : [Disabled]

                    Advanced Clock Control ------- [Press Enter]
                    CPU Clock Drive ---------------------- : [800mV]
                    PCI Express Clock Drive -------------- : [800mV]
                    CPU Clock Skew (ps) ------------------ : [0]
                    MCH Clock Skew (ps) ------------------ : [0]

                    DRAM Performance Control
                    Performance Enhance ------------------- : [Standard]
                    Extreme Memory Profile --- (X.M.P.) --- : [Disabled]
                    (G)MCH Frequency Latch ---------------- : [Auto]
                    System Memory Multiplier -------------- : [4.00D] << Try 3.33D for now as suggested above
                    Memory Frequency (Mhz) ---------------- : [1600]
                    DRAM Timing Selectable ---------------- : [Manual]

                    Standard Timing Control
                    CAS Latency Time -------- 9 ---------- : 8
                    tRCD ------------------- 9 ---------- : 8
                    tRP --------------------- 9 ---------- : 8
                    tRAS ------------------- 24 ---------- : 24

                    Advanced Timing Control
                    tRRD ------------------- 4 ---------- : 4
                    tWTR ------------------- 5 ---------- : 6
                    tWR --------------------- 10 ---------- :8
                    tRFC ------------------- 74 ---------- : 72-80
                    tRTP ------------------- 5 ---------- : 4
                    Command Rate (CMD) -------------------- :2

                    Channel A
                    Static tRead Value --------------------- :9
                    tRD Phase0 Adjustment ------------------ :0 [Auto]
                    tRD Phase1 Adjustment ------------------ :0 [Auto]
                    tRD Phase2 Adjustment ------------------ :1 [Auto]
                    tRD Phase3 Adjustment ------------------ :1 [Auto]
                    Trd2rd(Different Rank) ----------------- :7 [Auto]
                    Twr2wr(Different Rank) ----------------- :6 [Auto]
                    Twr2rd(Different Rank) ----------------- :6 [Auto]
                    Trd2wr(Same/Diff Rank) ----------------- :9 [Auto]
                    Dimm1 Clock Skew Control --------------- : [Auto] ps
                    Dimm2 Clock Skew Control --------------- : [Auto] ps

                    Channel B
                    Static tRead Value --------------------- :9 [Auto]
                    tRD Phase0 Adjustment ------------------ :0 [Auto]
                    tRD Phase1 Adjustment ------------------ :0 [Auto]
                    tRD Phase2 Adjustment ------------------ :1 [Auto]
                    tRD Phase3 Adjustment ------------------ :1 [Auto]
                    Trd2rd(Different Rank) ----------------- :7 [Auto]
                    Twr2wr(Different Rank) ----------------- :6 [Auto]
                    Twr2rd(Different Rank) ----------------- :6 [Auto]
                    Trd2wr(Same/Diff Rank) ----------------- :9 [Auto]
                    Dimm1 Clock Skew Control --------------- : [Auto] ps
                    Dimm2 Clock Skew Control --------------- : [Auto] ps


                    Motherboard Voltage Control
                    CPU
                    Voltage Types------------ Normal -------- Current -----
                    Load-Line Calibration ----------------- : [Disabled]
                    CPU Vcore --------------- 1,22500V ---- :1,33125V

                    CPU Termination --------- 1,2V ----- : 1,3V << 1.2-1.28 may be ok
                    CPU PLL ----------------- 1,550V ----- : 1,550V (steps only 1.55,1.66 ect)

                    CPU Reference ----------- 0,805V* ----- : [Auto]
                    CPU Reference2 ---------- ?.???V* ----- : [Auto]

                    MCH/ICH
                    MCH Core ---------------- 1,100V ------- :1,26
                    MCH Reference ----------- 0,760V ------- : [Auto]
                    MCH/DRAM Ref ------------ ?????V ------ : [Auto]
                    ICH I/O ----------------- 1,550V ------- : [Auto]
                    ICH Core ---------------- 1,100V ------- : [Auto]

                    DRAM
                    DRAM Voltage ------------ 1,500V ------- :1,66V
                    DRAM Termination -------- 0,750V ------- : [Auto]
                    Channel A Reference ----- ?.???V ------- : [Auto]
                    Channel B Reference ----- ?.???V ------- : [Auto]

                    Advanced Settings
                    Limit CPUID Max. to 3 ------------------ : [Disabled]
                    No-Execute Memory Protect -------------- : [Enabled]
                    CPU Enhanced Halt (C1E) ---------------- : [Disabled]
                    C2/C2E State Support ------------------- : [Disabled]
                    x C4/C4E State Support ----------------- : [Disabled]
                    CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
                    CPU EIST Function --------------------- : [Disabled]
                    Virtualization Technology -------------- : [Disabled]

                    Integrated Peripherals
                    Legacy USB Storage Detect ------------- : [Disabled]

                    Comment


                    • #11
                      Re: Oc ram + cpu

                      wibujo couldn't use the 4.00D multiplier on his EP45T-USB3P baord but managed 450MHz FSB x 3.33D for DDR-1500, this should get the CPU up to 3.85GHz.
                      Both are very new boards maybe BIOS update will allow it but to get above 3.4 you need more than 400MHz FSB anyway.

                      Comment

                      Working...
                      X