New over here, help with little OC

[DimasL]

[wazza300]

Re: New over here, help with little OC

For 3.2ghz try 21x151 bclk,then manually disable xmp and set spd system memory multiplier to 12x to give you 1812mhz speed,set your timing manually then choose quick and type in timings like this but according to your ram
8
8
8
24
Command rate 1t
Set dram voltage to 1.66v,set cpu voltage to normal in cpu voltage list,set qpi/vtt voltage to 1.32v

[DimasL]

Re: New over here, help with little OC

If i set 151x21 it gives me 3.17, is it ok?? i set it to 153x21 to get 3.21, with the rest of the settings u gave me.

I was coping the bios template to a txt, ill post in a moment.

GOT BSOD 0x00000124 : l

Solved, set the qpi/vtt voltage to 1.34v had to pass lynX to check it well

0x00000124 after 4mins with lynx :(

[DimasL]

Re: New over here, help with little OC

Thats how i had the bios before change what u told me. Anything else i should deactivate/activate to get better stability?

[B]>MB Intelligent Tweaker (M.I.T.)[/B]
[I]->Advanced Frequency Settings[/I]
CPU Clock Ratio ............................ [18x]
CPU Frecuency .............................. 2.70 (150x18)
[I]-->Advanced CPU Core Features[/I]
QPI Cloak Ratio ............................ [Auto]
QPI Link Speed ............................. 5.4GHz
Uncore Clock Ratio ......................... [Auto]
Uncore Frequency ........................... 3600MHz
>>>>> Standard Clock Control
Base Clock(BCLK) Control ................... [Enable]
BCLK Frequency(MHz) [150]
Extreme Memory Profile(X.M.P.) ............. [Profile2]
System Memory Multiplier (SPD) ............. [Auto]
Memory Frequency(Mhz) 1800 ................. 1800*
PCI Express Frequency(Mhz) ................. [Auto]
>>>>> Advaced Clock Control
CPU Clock Drive ............................ [800mV]
PCI Express Clock Drive .................... [900mV]
CPU Clock Skew ............................. [0ps]
IOHClock Skew .............................. [0ps]

[I]--> Advanced CPU Core Features[/I]
Intel� Turbo Boost Tech. ................... [Enable]
CPU Cores Enable ........................... [All]
CPU Multi-Threading ........................ [Enable]
CPU Enhanced Halt (C1E) .................... [Enable]
C3/C6/C7 State Support ..................... [Disable]
CPU Thermal Monitor ........................ [Enable]
CPU EIST Function .......................... [Enable]
Bi-Directional PROCHOT ..................... [Enable]

[B]->Advanced Memory Settings[/B]
Extreme Memory Profile(X.M.P.) ............. [Profile2]
System Memory Multiplier (SPD) ............. [Auto]
Memory Frequency(Mhz) 1800 ................. 1800*
Performance Enhance [Turbo]
DRAM Timing Selectable (SPD) ............... [Auto]
Profile DDR Voltage ........................ 1.65V*
Profile QPI Voltage ........................ 1.5V*
x Channel Interleaving 6 ................... Auto*
x Rank Interleaving 4 ...................... Auto*
>>>>> Channel A
x CAS Latency Time 9 ....................... [Auto]
x tRCD 9 ................................... [Auto]
x tRP 9 .................................... [Auto]
x tRAS 27 .................................. [Auto]
>>>>> Channel B
x CAS Latency Time 9 ....................... [Auto]
x tRCD 9 ................................... [Auto]
x tRP 9 .................................... [Auto]
x tRAS 27 .................................. [Auto]
>>>>> Channel C
x CAS Latency Time 9 ....................... [Auto]
x tRCD 9 ................................... [Auto]
x tRP 9 .................................... [Auto]
x tRAS 27 .................................. [Auto]

[B]->Advanced Voltage Settings[/B]
>>> CPU
Load-Line Calibration ...................... [Auto]
CPU Vcore 1.18125V ......................... [Auto]
x Dynamic Vcore(DVID) +0.00000V ............ [Auto]
QPI/Vtt Voltage 1.150V ..................... [Auto]
CPU PLL 1.800V ............................. [Auto]
>>> MCH/ICH
PCIE 1.500V ................................ [Auto]
QPI PLL 1.100V ............................. [Auto]
IOH Core 1.100v ............................ [Auto]
ICH I/O 1.500v ............................. [Auto]
ICH Core 1.100 ............................. [Auto]
>>> DRAM
DRAM Voltage 1.500v ........................ [Auto]
DRAM Termination 0.750v .................... [Auto]
Ch-A Data V.Ref. 0.750v .................... [Auto]
Ch-B Data V.Ref. 0.750v .................... [Auto]
Ch-C Data V.Ref. 0.750v .................... [Auto]
Ch-A Address V.Ref. 0.750v ................. [Auto]
Ch-B Address V.Ref. 0.750v ................. [Auto]
Ch-C Address V.Ref. 0.750v ................. [Auto]

[B]->Miscellaneous Settings[/B]
Isochronous Support ........................ [Enabled]
Virtualization Technology .................. [Enabled]

[Chike]

Re: New over here, help with little OC

QPI/Vtt 1.5v no a very good idea, Intel says max 1.35v.

[Acebmxer]

Re: New over here, help with little OC

You can run higher then 1.5v for qpi/vtt just not preferred to run over 1.4 for 24/7.

@DimasL Please fill in your current bios settings. the ones you posted all voltage settings are set to auto.

If qpi/vtt is higher then it needs to be you can get bsod error 124 if it is to low you can get error 124. Make sure your uncore multi is 2x ram multi or +1 or +2 higher uncore = more qpi/vtt voltage Higher blck = higher qpi/vtt higher memory speed = higher qpi/vtt and ram voltage higher cpu speed = higher vcore.

[Lsdmeasap]

Re: New over here, help with little OC

You shouldn't need 1.5, or more, for only 1800Mhz memory.

You need to lower your QPI and set your memory timings yourself disable XMP. You wont be able to use the 1600Mhz timings at 1800Mhz, so you'll need to loosen those up for sure and that is why I said to disable XMP as it's only going to cause you issues since you are overclocking.

Then also set the uncore manually as mentioned above.

[Chike]

Re: New over here, help with little OC

This ram has 2 XMP profiles, for 1600 and 1800Hz

[Lsdmeasap]

Re: New over here, help with little OC

Ahh ok, well then the timings are probably ok then and he just needs to adjust something else.

[Chike]

Re: New over here, help with little OC

Ahh ok, well then the timings are probably ok

Wouldn't be too sure about that untill i see the profiles. While searching them I saw a set which it's prfiles were messed up in OCZ forums.

@DimasL
Can you post a screen capture of CPU Tweaker for all 3 DIMMs?

[Lsdmeasap]

Re: New over here, help with little OC

I can believe that! This is part of the reason I suggest XMP disabled all the time anyway, especially when someone is not using stock Bclk.

[wazza300]

Re: New over here, help with little OC

I only suggested 151x21 bclk so you didn't oc your ram too much,you could try 1.36v for qpi/vtt, or drop to 10x mem multi and run ram at 1530mhz and set qpi/vtt voltage to 1.315v? It's up to you

[DimasL]

Re: New over here, help with little OC


@Acebmxer The BIOS template y posted before y what i have as settings right now, cuz i couldnt get any stable with the little OC. And yes the ram has 2 XMP Profiles one for 1600 and the otherone for 1800 with diferent timmings i think.

@Chike im not sure if this is what u request



BTW This is the temps and voltages i got with hardware monitor right now, with default bios, the same as i posted before.



Arent the temps a little higher to be idle??
Is the +12v ok? :s

Im was thinking before get the little OC, first get a stable 2.66GHz without the all auto settings on the bios. Or isnt a problem to go for 3.2Ghz?

[wazza300]

Re: New over here, help with little OC

Depends on room temp,Spain is hotter than the UK,you can keep cpu voltage on normal instead of auto,and set dram voltage to 1.66v,those two are fine for upto 3.8ghz,could try around 1.3 to 1.35v for qpi/vtt voltage

[Chike]

Re: New over here, help with little OC

I meant the SPD window, for all 3 DIMMs, or just one if all the same, but it seems to set timings correctly if that is set by XMP.