Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 10 of 10

Thread: amd 1800+ fsb100????????




  1. #1
    Join Date
    Aug 2002
    Posts
    77

    Default

    my sys
    asus a7v333
    2 x 256 pc2700 generic
    1800+amd @1150?
    a250 td ultra leadtek
    volc. 7+
    400w powermax
    enermax case
    5 casefans
    40gb 7200 wd
    40gb 7200 maxtor

    Problem.......... system has been running fine for about 8 mths and all of a sudden the cpu keeps resetting to 1150mhz and 100fsb in bios.
    if i get it to boot at 1533mhz 133fsb it either tells me it has failed due to overclocking or it gets to the win xp logon and freezes.
    it was running at 1533mhz 133fsb before.........wtf?
    tried replacing ram but still does same.
    the one thing thats was done just prior to the prob was i had the hsf replaced from gen. amd to the volc 7+.
    cpu was running at between 58 and 70 deg cels.
    now at 1150 its running at 41 with fan on med.
    could replacing the hsf cracked or disturbed the cpu????
    confused? me too.
    any suggestions appreciated

  2. #2
    Join Date
    Jan 2002
    Posts
    474

    Default

    Hmm, the Volcano 7+ can put a bit of stress on your CPU when putting it down, but if you were careful I doubt there would be any problem.

    Have you made sure you mounted the Volcano 7+ correctly (check to make sure that lip isn't switched), and that you didn't disturb any jumpers, etc.. when you changed your heatsink? Also, have you tried switching back to your stock AMD heatsink and seeing if the problem is still there? Give that a shot.

    After checking those two things, clearing your CMOS might help. If there was a soft-setting changed by accident/bug/default/freak occurance, it may cause your problem. Just make sure you remember your tweaked settings, if there are any.

    I also looked at your motherboard manual. There should be some blue/white DIP switches below your AGP port. Make sure they're set to: -____- (1-on, 2-off, 3-off, 4-off, 5-off, 6-on) for 133MHz operation.

    Hope that helps.



    ----
    Your motherboard manual can be found here.
    Chris "Raven"
    News Crew - TweakTown
    <!--
    <font size=1>
    <font color=green>Main Beast:</font>
    - Athlon XP 1800+@1701MHz | EPoX 8KHA+ | Corsair 512MB XMS3200C2 | GeForce3 Ti200
    - 2x80GB WD 7200RPM | 40x12x48 Sony CDRW | Pioneer 16X DVD
    - Swiftech MCX462+ / Tt Smart Case Fan 2 | Antec 1030SX case w/ 431W Enermax PSU
    </font>
    // -->
    "Look at life like your morning cup of coffee. You might have one every day, yet you still enjoy it."

    How to ask a good question

  3. #3
    Join Date
    Aug 2002
    Posts
    77

    Default

    still havnt found a solution................
    tried new ram....... no
    tried bios update.........no
    tried new h/d and fresh win xp load.......no
    tried dip swiches .......no
    cpu still runs fine but is a dog when printing as it stops responding till printer is finished.
    still set at 1160 mhz temp and volts all fine
    cpu core temp 38'
    cpu volt 1.76
    100 fsb

    any suggestions?????????:cry: :cry: :cry:

  4. #4
    Join Date
    Sep 2002
    Posts
    1,636

    Default

    cpu was running at between 58 and 70 deg cels.
    I think thats way hot!!!
    I would take off the 7+ and look at the chip.

    I dont think you have it on backwards, because your temps now are good.

  5. #5
    Join Date
    Aug 2002
    Location
    Ohio, USA
    Posts
    1,296

    Default

    Do you have your HSF powered off of the mobo? If so, try powering it with a 4 pin Molex connector. Make sure to connect the speed sensor to the mobo.

  6. #6
    Join Date
    Mar 2003
    Posts
    3

    Default

    I have the same system (pretty much) and was also contemplating on changing my generic fan on CPU to something like a Vol 7+. My system runs slow as well when I go to print…but isn’t unstable I can still do other things. Did you try putting the generic fan on it again to see if you get the 1.53 reading? Good luck. :confused:
    2400+ XP | Asus A7V8X | 9600 AIW | 512 DDR 2700 |

  7. #7
    Join Date
    Feb 2003
    Location
    Fincastle, IN, USA
    Posts
    3,776

    Default

    i had the same prob with my rig, and i was using the stock HSF, i went out and bought a Kingwin copper HSF, and its been running the 133fsb ever since, so u may be overheating

  8. #8
    Join Date
    Apr 2003
    Posts
    1

    Default

    Hi this sounds like two things
    1 cpu overheated the vol 7 will do the job thow
    2 CMOS needs to be wiped

    1 susgest you reseat your HSF again but check for any damage first to cpu

    2 wipe the CMOS then change the bios settings [save the settings ]

    if this doesn't work try getting some one to test your cpu in another board & another cpu in your mobo

  9. #9
    Join Date
    Aug 2002
    Location
    Quebec, Canada
    Posts
    1,369

    Default

    Did you use any thermal compound ???
    I have the same CPU and HSF. I've never had a problem. I've always used Arctic Silver 3. (Use a thin coat only.)
    SPAM Special Ops

  10. #10
    Join Date
    Mar 2003
    Posts
    111

    Default

    first i would try the old HSF, maybe the new one is drawing too much power from the mobo.
    second, try clearing the cmos using the jumpers and unplug the battery for an hour.
    third i would reflash the bios.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •