Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 7 of 7

Thread: AT style HD problem.




  1. #1
    Join Date
    Nov 2001
    Posts
    1,599

    Default

    So today I was going though some old computer parts, and I discovered an old 80 meg maxtor HD, that appears to be AT style (is the the correct terminology?) It does not have any jumpers, just IDE and power connection. So I installed it in a old system, Pentium 233, just to see what was on the HD, and apparently the formats are not compatible.

    I had installed it on the primary IDE controller, in the slave position. The Primary IDE controller no longer responds, but after hooking the HD up to the secondary IDE controller, and made the CD-rom slave, the computer works just fine.

    I'm wondering what exactly I did, and if there is any way to ressurect the Primary controller. I know ATA 33/66 controllers are cheap as dirt, but if there is a simple fix to this I'd rather do it.

    Do you think flashing the bios would help me? Any other thoughts/tips ?

    Thanks....

  2. #2
    Beefy Guest

    Default

    OK.. firstly, I don't quite think AT style is appropriate terminology.. AT is usually refering to the type of power supply / connector in a case.

    with the HDD, is there any jumpers on any visible circuit board... usually on the bottom. Many old HDDs didn't have the jumpers on the back, but were cleverly hidden on a visible part of the PCB. Best thing to do would be to check out the Maxtor site for any information you can find on the HDD.

    What do you mean 'formats are incompatible'?

    It's also interesting that a HDD killed your IDE controller.. but if the HDD was faulty to begin with, then there's that slight chance that it may have fried it. Someone else here should be able to give you more info...

  3. #3
    Join Date
    Nov 2001
    Posts
    1,599

    Default

    I know what AT is usually used to describe.. I went on ebay and found a similar HD and they refered to it as an AT hard drive.

    There are no jumpers anywhere. I know what you are getting at though, I have a 250 meg drive with the jumpers around on the PCB.

  4. #4
    Join Date
    Nov 2001
    Posts
    1,599

    Default

    AT is also used to describe motherboard layout, and keybaord connections to AT motherboards.

  5. #5
    Join Date
    Nov 2001
    Location
    New England Highlands, Australia
    Posts
    21,907

    Default

    Well I'll sort ya's out on this. ;)
    <a href="http://www.pcguide.com/ref/hdd/if/ide/index-c.html" target="_blank">The correct term is: Integrated Drive Electronics / AT Attachment (IDE/ATA) Interface</a>
    So check that out. :)
    But ya bit on format compatability is probably this,
    <a href="http://www.pcguide.com/ref/hdd/if/ide/modes-c.html" target="_blank">IDE/ATA Transfer Modes and Protocols</a> :smokin:
    <center>:cheers:</center>

  6. #6
    Join Date
    Nov 2001
    Location
    Texas, USA
    Posts
    4,825

    Default

    It may not boot up as a slave drive, but you can probably just disconnect your normal drive, install this one as the master, and then boot up with an old Win98 boot disk. Then you can scrounge around on the drive and see what is hidden there. :)
    Old age and treachery will overcome youth and skill
    My Toys

  7. #7

    Default

    i doubt it killed your primary IDE controller, probably just tried to be master drive, beside the other master drive you already had there...
    sKuLLsHoT
    www.morb.ath.cx

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •